1. REGISTRATION
AFTER REPLACING INJECTOR(S) WITH NEW ONE(S), INPUT COMPENSATION CODE(S) OF INJECTOR(S) INTO ECM AS FOLLOWS
When an injector is replaced, the new injector's compensation code must be input into the ECM. When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.
Injector compensation codes are unique, 30 digit, alphanumeric values printed on the head portion of each injector. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Do not start the engine.
The injector compensation code is printed on the head portion of each injector.
Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Injector Compensation.
| Tester Display |
|---|
| Injector Compensation |
Press Next.
Press Next again to proceed.
Select "Set Compensation Code".
Press Next.
Select the number of the cylinder corresponding to the injector compensation code that you want to read.
Press Next.
Register compensation code.
Press Input.
Manually input the cylinder's compensation code using the GTS keyboard. The code is a 30 digit, alphanumeric value printed on the injector's head portion.
Each injector compensation code is unique. The compensation code for each selected cylinder must be input into the GTS correctly.
Confirm that the compensation code for the selected cylinder is correct, and then press OK.
Check that the compensation code displayed on the screen is correct by comparing it with the 30 digit alphanumeric value on the head portion of the injector.
If an incorrect injector compensation code was input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.
If a wrong compensation code was input or read, return to the Input Value screen by pressing Input.
The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.
Press Next to set the compensation code to the ECM.
If the setting process fails, the compensation code may be incorrect. Check the compensation code again.
If the input compensation code fails to set even though it is input correctly, there may be a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.
If you want to continue with other compensation code registrations, press Next. To finish the registration, press Cancel.
Turn the ignition switch off and then turn the GTS off.
Wait for at least 30 seconds.
Turn the ignition switch to ON and then turn the GTS on.
Clear DTC P1601 stored in the ECM using the GTS.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>DTC CHECK / CLEAR
WHEN REPLACING ECM WITH NEW ONE, INPUT ALL INJECTOR'S COMPENSATION CODES INTO NEW ECM AS FOLLOWS:
When an injector is replaced, the injector's compensation code must be input into the ECM.
When the ECM is changed, all of the existing injector compensation codes must be input into the new ECM.
Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector. If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.
The following operation is available with ECMs that can transmit the registered injector compensation codes to the GTS.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Do not start the engine.
The injector compensation code is imprinted on the head portion of each injector.
Enter the menu options in this order: Power train / Engine and ECT / Utility / Injector Compensation.
| Tester Display |
|---|
| Injector Compensation |
Press Next.
Press Next again to proceed.
Select Read Compensation Code.
Press Next.
Select the number of the cylinder corresponding to the injector compensation code that you want to read.
Press Next.
The reading process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and restart this operation.
Check the injector compensation code (30-digit alphanumeric value) is displayed on the GTS screen.
Press Save.
Check that the compensation code displayed on the GTS screen is correct.
| *a | When no injection compensation code for the cylinder exists in the GTS: | *b | When another injector compensation code for the cylinder exists in the GTS: |
Press Save or Replace, save the injector compensation code.
The existing compensation code is overwritten with the new compensation code and is deleted from the GTS.
The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.
If you want to read and save other injector compensation codes for other cylinders, press Next to continue. To finish this operation, press Cancel.
Turn the ignition switch off.
Turn the GTS off.
Replace the ECM.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Do not start the engine.
The injector compensation code is imprinted on the head portion of each injector.
Enter the menu options in this order: Power train / Engine and ECT / Utility / Injector Compensation.
| Tester Display |
|---|
| Injector Compensation |
Press Next.
Press Next again to proceed.
Select Set Compensation Code.
Press Next.
Select the number of the cylinder corresponding to the injector compensation code that you want to read.
Press Next.
Check that the compensation code displayed on the screen is correct, by comparing it with the 30-digitalphanumeric value on the head portion of the injector.
If an incorrect injector compensation code was input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.
If a wrong compensation code was input or read, return to the input Value screen by pressing input.
The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.
Press Next to set the compensation code to the ECM.
If the setting fails, the compensation code may be incorrect. Check the compensation code again.
If a wrong compensation code was input or read, return to the input Value screen by pressing input.
If the attempted compensation code is correct, a problem with the wire harness or a bad connection with the DLC3 may cause the failure.
Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.
If you want to continue with other compensation code registrations, press Next. To finish the registration, press Cancel.
Turn the GTS off and then turn the ignition switch off.
Wait for at least 30 seconds.
Turn the ignition switch to ON and then turn the GTS on.
Clear DTC P1601 stored in the ECM using the GTS.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>DTC CHECK / CLEAR
2. DESCRIPTION OF VIN
The Vehicle Identification Number (VIN) or frame number must be input into a replacement ECM.
The VIN is a 17-digit alphanumeric vehicle identification number. The GTS is required to register the VIN.
This registration section consists of two parts, Read VIN or Frame Number and Write VIN or Frame Number.
Read VIN or Frame Number: This procedure allows the VIN or frame number stored in the ECM to be read in order to confirm that the VINs or frame numbers, provided on the vehicle body and stored in the vehicle ECM, are the same.
Write VIN or Frame Number: This procedure allows the VIN or frame number to be written into the ECM. If the ECM is replaced, or the ECM VIN or frame number and vehicle VIN or frame number do not match, the VIN or frame number can be registered, or overwritten in the ECM by following this procedure.
3. READ VIN OR FRAME NUMBER
Confirm the vehicle VIN or frame number.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / VIN / VIN Read.
| Tester Display |
|---|
| VIN |
According to the display on the GTS, read the VIN or frame number stored in the ECM.
4. WRITE VIN OR FRAME NUMBER
Confirm the vehicle VIN or frame number.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / VIN / VIN Write.
| Tester Display |
|---|
| VIN |
According to the display on the GTS, write the VIN or frame number to the ECM.