Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › from 2019.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) U

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS's Data List allows switch, sensor, actuator, and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.

HINT:

To display the entire Data List, press the pull down menu button next to Primary. Then select All Data.




Engine Control


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h, Max.: 255 km/h Actual vehicle speed Speed indicated on speedometer
Target Idle Engine Speed Target engine speed Min.: 0 rpm, Max.: 10000 rpm - -
Engine Speed Engine speed Min.: 0 rpm, Max.: 16383.75 rpm Idling: 500 to 600 rpm -
Calculate Load Calculated load by ECM Min.: 0%, Max.: 100%
·

Idling: 15.4 to 20.4%

·

Running without load (2500 rpm): 20.1 to 25.9%


-
MAF Air flow rate from MAF meter status Min.: 0 gm/sec., Max.: 655.35 gm/sec.
·

Idling: 6.1 to 26.5 gm/sec.

·

Running without load (3000 rpm): 68 to 170 gm/sec.


If value approximately 0 gm/sec.:
·

Mass air flow meter power source circuit open

·

VG circuit open or shorted


If value 240 gm/sec. or more:
EVG circuit open
Atmosphere Pressure Atmospheric pressure value Min.: 0 kPa, Max.: 255 kPa Actual atmospheric pressure -
MAP Absolute pressure inside intake manifold Min.: 0 kPa, Max.: 255 kPa
·

Idling: 90 to 102 kPa

·

Engine running at 3000 rpm: 100 to 150 kPa


-
Coolant Temp Engine coolant temperature Min.: -40°C, Max.: 140°C After warming up engine: 75 to 90°C (167 to 194°F) If value is -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
Intake Air Intake air temperature Min.: -40°C, Max.: 140°C Equivalent to temperature at intake manifold If value is -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
Intake Air Temp (Turbo) Intake air temperature Min.: -40°C, Max.: 190°C 70°C (158°F) or less -
Engine Run Time Engine run time Min.: 0 s., Max.: 65535 s. Time after engine started Service data
Initial Engine Coolant Temp Initial engine coolant temperature Min.: -40°C, Max.: 120°C Engine coolant temperature when engine started -
Initial Intake Air Temp Initial intake air temperature Min.: -40°C, Max.: 120°C Intake air temperature when engine started -
Battery Voltage Battery voltage Min.: 0 V, Max.: 65.535 V 11 to 14 V -
Alternate Duty Ratio Alternator generation duty ratio Min.: 0%, Max.: 100%
·

No electrical load at idling:

20 to 60%

·

High electrical load at idling:

100%


·

This is outputs the alternator generation duty and is used to determine the electrical load.

·

Can be used to determine whether a higher-than-normal injection volume at idle, etc. is due to electrical loading or from some other source. For example, when the duty is not high but the idling injection volume is high, there is injector volume degradation or high engine friction.

·

Can be used for judging whether or not a malfunctioning component in the electrical system is generating continual generation requests (e.g., battery deterioration is causing an unending full recharge request, etc.). Regardless of whether or not an auxiliary device like the A/C or heater is active, if the alternator duty is always at the maximum value, there is an electrical system abnormality, like battery deterioration.


Pre Glow Pre-glow operation ON or OFF - This is the ECM command.
After Glow After-glow operation ON or OFF - This is the ECM command.
Accel Position Accelerator position status Min.: 0%, Max.: 100%
·

Accelerator pedal released:

0%

·

Accelerator pedal depressed:

100%


Read value with ignition switch ON (do not start engine)
Accel Sens. No.1 Volt % Accelerator position No. 1 Min.: 0%, Max.: 100%
·

Accelerator pedal released:

10 to 22%

·

Accelerator pedal fully depressed:

52 to 90%


Read value with ignition switch ON (do not start engine)
Accel Sens. No.2 Volt % Accelerator position No. 2 Min.: 0%, Max.: 100%
·

Accelerator pedal released:

24 to 40%

·

Accelerator pedal fully depressed:

68 to 99%


Read value with ignition switch ON (do not start engine)
Accel Sensor Out No.1 Accel sensor No. 1 output voltage Min.: 0 V, Max.: 4.98 V - Read value with ignition switch ON (do not start engine)
Accel Sensor Out No.2 Accel sensor No. 2 output voltage Min.: 0 V, Max.: 4.98 V - Read value with ignition switch ON (do not start engine)
Starter Signal Starter signal ON or OFF ON: Cranking -
Low Gear Switch Low gear switch signal ON or OFF - -
Clutch Switch First position switch ON or OFF ON: First position -
Stop Light Switch Stop light switch signal ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
A/C Signal A/C signal ON or OFF ON: A/C ON -
Immobiliser Communication Immobiliser communication ON or OFF ON: Normal -
Check Mode Check mode ON or OFF ON: Check mode on The mode in which certain DTCs can be detected more easily and with higher sensitivity.
SPD Test Result Check mode result for vehicle speed sensor Compl or Incompl - Check mode result for the vehicle speed sensor.
# Codes(Include History) Number of codes Min.: 0, Max.: 255 - Number of DTCs appearing at least once during the last 40 times the vehicle was warmed up.
MIL MIL status ON or OFF OFF: MIL off -
MIL ON Run Distance Distance traveled with MIL on Min.: 0 km
Max.: 65535 km
Distance traveled after DTC stored
·

Distance traveled after a DTC is stored.

·

Cleared when the cable is disconnected from the negative (-) battery terminal, or when the DTC is cleared using the intelligent tester.


Running Time from MIL ON Running time after MIL turns on Min.: 0 km
Max.: 65535 km
Running time after MIL turns on
·

Engine run time since the MIL illumination.

·

Cleared when the cable is disconnected from the negative (-) battery terminal, or when the DTC is cleared using the intelligent tester.


Time after DTC Cleared Time after DTC cleared Min.: 0 min., Max.: 65535 min. Equivalent to time after DTCs were erased -
Distance from DTC Cleared Distance after DTC cleared Min.: 0 km, Max.: 65535 km Equivalent to drive distance after DTCs were erased -
Warmup Cycle Cleared DTC Warmup cycle after DTC cleared Min.: 0, Max.: 255 - Number of warmup cycles after DTC cleared
Number of Emission DTC Number of emissions-related DTCs - - -
TC and TE1 Connect the TC and TE1 status for Active Test ON or OFF - Active Test support date
Engine Start Time Engine start time Min.: 0 ms, Max.: 267000 ms - Service data
ACT VSV A/C cut status for Active Test ON or OFF - Active Test support date

Compression


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed of Cyl #1 Engine speed for No. 1 cylinder Min.: 0 rpm, Max.: 25600 rpm Engine speeds of all cylinders almost same
·

Output only when the "Check the Cylinder Compression" Active Test is performed.

·

Indicates the speed of each cylinder when cranking.

Example - Normal: Engine speeds of all cylinders are approximately equal.

When No. 1 cylinder compression is low, "Engine Speed of Cyl #1" is approximately 300 rpm, and "Engine Speed of Cyl #2 to #8" is approximately 200 rpm.


Symptoms when out of range:
When the engine speeds of all cylinders are not equal, idling will be rough.
Cause of Out of Range:
Cyl #1 compression goes down
Engine Speed of Cyl #2 Engine speed for No. 2 cylinder Min.: 0 rpm, Max.: 25600 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #3 Engine speed for No. 3 cylinder Min.: 0 rpm, Max.: 25600 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #4 Engine speed for No. 4 cylinder Min.: 0 rpm, Max.: 25600 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #5 Engine speed for No. 5 cylinder Min.: 0 rpm, Max.: 25600 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #6 Engine speed for No. 6 cylinder Min.: 0 rpm, Max.: 25600 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #7 Engine speed for No. 7 cylinder Min.: 0 rpm, Max.: 25600 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #8 Engine speed for No. 8 cylinder Min.: 0 rpm, Max.: 25600 rpm Engine speeds of all cylinders almost same -
Av Engine Speed of All Cyl Engine speed for all cylinders Min.: 0 rpm, Max.: 25600 rpm -
·

Output only when the Active Test "Check the Cylinder Compression" is performed.

·

Indicates the average engine speed of all cylinders during cranking.



Vehicle Information


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Model Code Model code - - -
Engine Type Engine type - - Identifying engine type: 1VD-FTV
Cylinder Number Cylinder number Min.: 0, Max.: 255 - Identifying cylinder number: 6
Transmission Type Transmission type MT or ECT - MT (Manual transmission)
Destination Destination - - -
Model Year Model year Min.: 1900, Max.: 2155 - Identifying model year: 20##
System Identification System identification - - Identifying engine type: Diesel

Diesel Injection


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Injection Volume Injection volume Min.: 0 mm3/st, Max.: 1279.98 mm3/st Idling: 3.0 to 10 mm3/st -
Inj. FB Vol. for Idle Idle stability status integral control volume Min.: -80 mm3/st, Max.: 79.9975 mm3/st -10 to 10 mm3/st
·

When the actual engine speed does not match the target idling speed, this corrects the injection volume.

If this item displays 10 mm3/st or more or -10 mm3/st or less even with the engine completely warmed up and the air conditioning and other electrical loads off, the internal parts of the engine may be damaged, or the fuel injection system or other auxiliary components may be malfunctioning.

·

Only calculated and reflected at idle.


Inj Vol Feedback Learning Injection volume feedback learning value Min.: -10 mm3/st, Max.: 9.92 mm3/st - -
Injection Feedback Val #1 Injection volume correction for No. 1 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Injection Feedback Val #2 Injection volume correction for No. 2 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Injection Feedback Val #3 Injection volume correction for No. 3 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Injection Feedback Val #4 Injection volume correction for No. 4 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Injection Feedback Val #5 Injection volume correction for No. 5 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Injection Feedback Val #6 Injection volume correction for No. 6 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Injection Feedback Val #7 Injection volume correction for No. 7 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Injection Feedback Val #8 Injection volume correction for No. 8 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Pilot 1 Injection Period Pilot 1 injection period Min.: 0 μs, Max.: 65535 μs Idling: 135 to 279 μs Check to see if "Pilot 1 Injection Period" is not zero when symptoms occur.
Pilot 2 Injection Period Pilot 2 injection period Min.: 0 μs, Max.: 65535 μs Idling: 113 to 312 μs Check to see if "Pilot 2 Injection Period" is not zero when symptoms occur.
Main Injection Period Main injection period Min.: 0 μs, Max.: 65535 μs -
·

When the fuel pressure becomes 15000 kPa or less, "Main Injection Period" is set to 0.

·

When the engine will not start, confirm that injection is performed.

·

When P0093, P0627 or P0200 is stored, there is an engine stall request. At that time, "Main Injection Period" equals 0.

HINT:

As the engine stalls 1 minute after the MIL illuminates, freeze frame data cannot be checked.



After Injection Period After injection period Min.: 0 μs, Max.: 65535 μs - Check to see if "After Injection Period" is not zero when the following symptoms occur: Black smoke, poor driveability.
Pilot 1 Injection Timing Pilot 1 injection timing Min.: -70 deg(CA), Max.: 20 deg(CA) Idling after engine warmed up and vehicle is under normal atmospheric pressure: 0 deg(CA) -
Pilot 2 Injection Timing Pilot 2 injection timing Min.: -50 deg(CA), Max.: 20 deg(CA) Idling after engine warmed up and vehicle is under normal atmospheric pressure: -1.4 to -5.4 deg(CA) -
Main Injection Timing Main injection timing Min.: -90 deg(CA), Max.: 90 deg(CA) Idling after engine warmed up and vehicle is under normal atmospheric pressure: -0.5 to 2.5 deg(CA) Use "Main Injection Timing" to check poor drivability when the following symptoms are present: Bad injection timing, black smoke, and white smoke.
After Injection Timing After injection timing Min.: -10 deg(CA), Max.: 50 deg(CA) - -
Injector Memory Error Injector memory error No Error or Error No Error If the injector compensation codes are not input into the new ECM, or if a injector compensation code of a different injector model or a compensation coderepresenting a value which exceeds the compensation setting range is input into the new ECM, DTC P1601 is stored and "Injector Memory Error" displays "Error".
Injection Pressure Correction Injection pressure feedback compensation volume Min.: -500 mm3/st, Max.: 799.9 mm3/st -20 to 20 mm3/st at standard temperature
·

When the (actual) common rail pressure is equal to the target common rail pressure, this value becomes 0.

·

This indicator can be used for diagnosing fuel supply pump assembly related malfunctions.

·

When this value (absolute value) is large, it indicates that the difference between the actual and target common rail pressure is also large.

·

A positive value indicates that the pressure feed is being increased due to insufficient pressure. A negative value indicates that pressure is being reduced due to excessive rail pressure.

·

When the suction control valve is malfunctioning, it causes rail overpressure, and this value slips to the negative volume side.

·

Injection Pressure Correction displays the value calculated by the ECM.


Target Common Rail Pressure Target common rail pressure Min.: 0 kPa, Max.: 655350 kPa 25000 to 160000 kPa -
Fuel Press Fuel pressure Min.: 0 kPa, Max.: 655350 kPa Idling: 27000 to 37000 kPa -
Fuel Temperature Fuel temperature Min.: -40°C, Max.: 215°C Actual fuel temperature After fully cold soaking the engine, the fuel temperature is the same as the outside air temperature.
Fuel Return Temp Fuel return temperature Min.: -40°C, Max.: 215°C Idling after engine warmed-up: 35 to 85°C If the "Fuel Return Temp" value is not between 55°C (131°F) and 130°C (266°F), "Pilot Quantity Learning" is prohibited.
Target Pump SCV Current Final pump current target value Min.: 0 mA, Max.: 8191.875 mA Idling: 923 to 1123 mA
·

ECU-calculated value for the suction control valve actuation target current.

·

Value is large when a high fuel pressure is desired.

·

Normally, the value is between 800 and 2500 mA.

·

If the value is stuck at 3000 mA or higher, it indicates that the operation is poor (poor movement due to deposits, etc.).

·

When this deviates from the standard value, it indicates that for some reason, even though the pump is running hard, the actual fuel pressure is inconsistent with the target fuel pressure.


Idle Injection Volume (Min) Minimum fuel injection volume Min.: 0 mm3/st, Max.: 39.8 mm3/st 3 to 10 mm3/st Service data

Diesel Throttle System


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Target Throttle Position Target throttle position Min.: -128%, Max.: 127%
·

Throttle valve fully opened:

0%

·

Throttle valve fully closed:

100%


If there is a malfunction of the throttle actuator, compare the target and actual throttle position values for troubleshooting.
Target Throttle Position #2 Target throttle position Min.: -128%, Max.: 127%
·

Throttle valve fully opened:

0%

·

Throttle valve fully closed:

100%


If there is a malfunction of the throttle actuator, compare the target and actual throttle position values for troubleshooting.
Actual Throttle Position Actual diesel throttle position Min.: -128%, Max.: 127% Idling after engine warmed-up:
5 to 100%
-
Actual Throttle Position #2 Actual diesel throttle position Min.: -128%, Max.: 127% Idling after engine warmed-up:
5 to 100%
-
Throttle Motor DUTY #1 Diesel throttle motor duty Min.: 0%, Max.: 100% - -
Throttle Motor DUTY #2 Diesel throttle motor duty Min.: 0%, Max.: 100% - -
Throttle Close Learning Val. Throttle fully closed position learned value (bank 1) Min.: 0 deg, Max.: 84 deg 14 to 22 deg
·

When the ignition switch is turned from ON to off and 5 seconds elapse, learning of "Throttle Close Learning Val." will be complete.

·

When "Throttle Close Learning Val." is outside of the normal range, a foreign object may lodged in the throttle valve.

·

If the value is stuck at the upper limit of 21.25 deg, there is a chance that a malfunction is present.

However, as the initial value for the learned value is 21.25 deg, it is necessary to check the value after learning is completed.


Throttle Close Learning Val.#2 Throttle fully closed position learned value (bank 2) Min.: 0 deg, Max.: 249.99 deg 14 to 22 deg
·

When the ignition switch is turned from ON to off and 5 seconds elapse, learning of "Throttle Close Learning Val.#2" will be complete.

·

When "Throttle Close Learning Val.#2" is outside of the normal range, a foreign object may lodged in the throttle valve.

·

If the value is stuck at the upper limit of 21.25 deg, there is a chance that a malfunction is present.

However, as the initial value for the learned value is 21.25 deg, it is necessary to check the value after learning is completed.


Diesel Throttle Learn Status Diesel throttle learning history OK or NG OK
·

If the system is functioning properly, learning will be performed when the ignition switch is turned from on to off.

·

NG indicates that a foreign object may be lodged in the throttle valve or actuator components, or a disconnection/short exists in the signal wires.


Diesel Throttle Learn Status #2 Diesel throttle learning history OK or NG OK
·

If the system is functioning properly, learning will be performed when the ignition switch is turned from on to off.

·

NG indicates that a foreign object may be lodged in the throttle valve or actuator components, or a disconnection/short exists in the signal wires.


Throttle Sensor Volt % Absolute throttle position sensor (bank 1) Min.: 0%, Max.: 100% Ignition switch ON: 60 to 80%
Warmed-up and idling: 10 to 80%
-

VN Turbo System


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Target Booster Pressure Target booster pressure Min.: 0 kPa, Max.: 639.98 kPa Driving vehicle on level surface at 3000 rpm with full load:
100 to 200 kPa
·

Inspect while comparing with "MAP".

·

With the accelerator fully open, if the actual manifold absolute pressure (MAP) is low compared to the target booster pressure by at least 20 kPa for 5 sec. or more, a feeling of a lack of power will occur.

·

When the vehicle is driven with the engine speed at 3000 rpm or more and the accelerator pedal fully depressed, "MAP" is approximately equal to "Target Booster Pressure".


Boost Pressure Deviation Boost pressure deviation Min.: -320 kPa, Max.: 320 kPa - -
VN Turbo Command VN turbo command Min.: -128%, Max.: 127% 0 to 100% ECD freeze frame data
VN Turbo Type VN turbo type Not Avl, Commo, Vacuum, CAN Com or DC Vacuum Indicates the VN turbo vane actuation method.
·

DC motor system.

·

Negative-pressure diaphragm system.

·

Step motor system.


VN Turbo Max Angle VN turbo maximum opening amount Min.: 0%, Max.: 99.6% 100%
HINT:

As this value displays the ideal constant upper limit, no matter what happens, this value should not change.


·

The maximum vane opening amount is displayed in %.

·

The VN turbo is operated between VN Turbo Max Angle and VN Turbo Min Angle when the Test the Turbo Charger Step Motor Active Test is performed.


VN Turbo Min Angle VN turbo minimum opening amount Min.: 0%, Max.: 99.6% 0%
HINT:

As this value displays the ideal constant lower limit, no matter what happens, this value should not change.


·

The maximum vane opening amount is displayed in %.

·

The VN turbo is operated between VN Turbo Max Angle and VN Turbo Min Angle when the Test the Turbo Charger Step Motor Active Test is performed.


VN Turbo Operation Prohibit VN turbo operation prohibit OK or NG OK -

Test Result (Monitor Status)


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Complete Parts Monitor Comprehensive component monitor Not Avl or Avail - *
Fuel System Monitor Fuel system monitor Not Avl or Avail - *
Misfire Monitor Misfire monitor Not Avl or Avail - *
EGR/VVT Monitor EGR/VVT monitor Not Avl or Avail - *
EGR/VVT Monitor EGR/VVT monitor Compl or Incmpl - *
O2S(A/FS) Heater Monitor O2S(A/FS) heater monitor Not Avl or Avail - *
O2S(A/FS) Heater Monitor O2S(A/FS) heater monitor Compl or Incmpl - *
O2S(A/FS) Monitor O2S(A/FS) monitor Not Avl or Avail - *
O2S(A/FS) Monitor O2S(A/FS) monitor Compl or Incmpl - *
A/C Monitor A/C monitor Not Avl or Avail - *
A/C Monitor A/C monitor Compl or Incmpl - *
2nd Air Monitor 2nd air monitor Not Avl or Avail - *
2nd Air Monitor 2nd air monitor Compl or Incmpl - *
EVAP Monitor EVAP monitor Not Avl or Avail - *
EVAP Monitor EVAP monitor Compl or Incmpl - *
Heated Catalyst Monitor Heated catalyst monitor Not Avl or Avail - *
Heated Catalyst Monitor Heated catalyst monitor Compl or Incmpl - *
Catalyst Monitor Catalyst monitor Not Avl or Avail - *
Catalyst Monitor Catalyst monitor Compl or Incmpl - *

*:

Avail: The monitor is available on the vehicle.

Not Avl: The monitor is not available on the vehicle.

Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once some time in the past. This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.


Diesel Starting


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed (Starter Off) Engine speed when starter off Min.: 0 rpm, Max.: 1593 rpm - Service data
Starter Count Starter ON count Min.: 0, Max.: 255 - Service data
Run Dist of Previous Trip Distance driven during previous trip Min.: 0 km, Max.: 326.4 km - Service data

Diesel Rough


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Electric Duty Feedback Value Electric load feedback value Min.: 0 mm3/st, Max.: 39.8 mm3/st 0 to 2 mm3/st Service data
A/C Duty Feedback Value A/C load feedback value Min.: 0 mm3/st, Max.: 39.8 mm3/st 0 to 2 mm3/st Service data
PS Duty Feedback Value Power steering load feedback value Min.: 0 mm3/st, Max.: 39.8 mm3/st - This item is displayed on the GTS but is not used.

ACTIVE TEST


HINT:

Performing the GTS's Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.

The Data List can be displayed during the Active Test.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


e.

Perform the Active Test.

Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the A/C Cut Signal Control the A/C signal ON/OFF -
Connect the TC and TE1 Turn on TC and TE1 connection ON/OFF -
Diesel Throttle Target Angle Control the diesel throttle valve (bank 1) 0 to 90% Test possible when following conditions met:
·

Ignition switch ON

·

Engine is stopped


Diesel Throttle Target Angle #2 Control the diesel throttle valve (bank 2) 0 to 90% Test possible when following conditions met:
·

Ignition switch ON

·

Engine is stopped


Test the Turbo Charger Step Motor Control the VRV for turbocharger 0 to 100%
·

Active Test available only while engine idling

·

Active Test only operates when value is 0%


Test the Fuel Leak Pressurizes common rail internal fuel pressure, and checks for fuel leaks Stop/Start
·

Fuel inside common rail pressurized to specified value and engine speed increased to 2000 rpm when Start is selected

·

Above conditions preserved while test is Start


Activate the VN Turbo Open Activate the turbocharger ON/OFF Confirm that the engine is running.
Control the Select Cylinder Fuel Cut Selected cylinder (cylinder #1 to #8) injector fuel cut
·

#1/#2/#3/#4/#5/#6/#7/#8

·

ON/OFF


Perform this test when the following conditions are met:
·

Confirm that the vehicle is stopped and the engine is idling.

·

If the running condition of the engine does not worsen even though injection of the designated cylinder is stopped, the cylinder can be determined to be malfunctioning.


Check the Cylinder Compression Check the cylinder compression pressure ON/OFF Fuel injection stops in all cylinders.*

*: In this Active Test, the fuel of all cylinders is cut, and cranking occurs for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is higher than the other cylinders, the compression pressure of that cylinder is determined to be lower than the other cylinders.

1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON and turn the GTS on.

5.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

HINT:

If the results are not displayed normally, select the display items from the Data List before performing the Active Test. Enter the following menus: Powertrain / Engine and ECT / Data List / Compression / Engine Speed of Cyl #1, Engine Speed of Cyl #2, Engine Speed of Cyl #3, Engine Speed of Cyl #4, Engine Speed of Cyl #5, Engine Speed of Cyl #6, Engine Speed of Cyl #7, Engine Speed of Cyl #8 and Av Engine Speed of All Cyl.


6.

While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

HINT:

After performing the above procedure, the Active Test's Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited, and each cylinder's engine rpm measurement will enter standby mode.


7.

Crank the engine for about 10 seconds.

8.

Monitor the engine speed (Engine Speed of Cyl #1 to #8, Av Engine Speed of All Cyl) displayed on the GTS.

HINT:

At first, the GTS's display will show each cylinder's engine rpm measurement to be extremely high. After approximately 10 seconds of engine cranking, each cylinder's engine rpm measurement will change to the actual engine rpm.


NOTICE:
·

After the Active Test's Check the Cylinder Compression is turned ON, it will automatically turn OFF after 255 seconds.

·

When the Check the Cylinder Compression test is OFF and the engine is cranked, the engine will start.

·

If the Check the Cylinder Compression test needs to be performed after it is turned ON and performed once, press EXIT to return to the Active Test menu screen. Then perform the Check the Cylinder Compression test again.

·

Use a fully-charged battery.