Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › from 2019.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  P1605  Rough Idling  


DESCRIPTION

This DTC is stored when the speed of a specific cylinder becomes low and the idle speed becomes unstable. This DTC is also stored if the vehicle runs out of fuel. Be sure to check whether there is enough fuel in the fuel tank before inspection.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1605 Rough Idling When the accelerator pedal is fully closed and the engine is idling, the speed of a specific cylinder is low for 2 to 10 seconds (1 trip detection logic).
·

Fuel injector

·

Injector compensation code

·

Fuel leak

·

Glow system

·

Intake air system leakage

·

Intake air system blockage

·

Throttle valve system

·

Suction control valve (fuel supply pump assembly)

·

Low quality fuel

·

Fuel filter element sub-assembly air bleed problem

·

Accessory problem (A/C, generator, etc.)

·

Engine assembly

·

ECM


- DTC stored

Related Data List
DTC No. Data List
P1605
·

Target Idle Engine Speed

·

Engine Speed

·

MAP

·

MAF

·

Coolant Temp

·

Battery Voltage

·

Engine Speed of Cyl #1 (to #8)

(Output only when the "Check the Cylinder Compression" Active Test is performed)

·

Intake Air

·

Target Common Rail Pressure

·

Fuel Press

·

Injection Feedback Val #1 (to #8)

·

Injection Volume

·

Actual Throttle Position

·

Actual Throttle Position #2

·

Rough Idle #1 (to #8)

·

Glow Relay Request

·

Glow Relay Request #2



CAUTION / NOTICE / HINT

In order for idling to be stable, glow system operation, fuel system operation and compression sufficient to maintain the target idling speed are necessary.



Glow system


a.

The following malfunctions may be present in the glow system.

i.

Engine coolant temperature sensor malfunction.


ii.

Glow plug malfunction.


iii.

Glow relay malfunction.




Fuel system


a.

The following malfunctions may be present in the fuel system.

i.

Fuel leakage.


ii.

Problem with injector assemblies.


iii.

Problem with fuel supply pump assembly.


iv.

Air in fuel pipe.




Engine assembly


a.

The following malfunctions may be present in the engine assembly.

i.

Insufficient compression.




HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 and P1605 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.

As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data.



PROCEDURE

1.DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 1))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

d.

Record the stored DTC and freeze frame data.

HINT:

This freeze frame data shows the actual engine conditions when the trouble occurred.



Result:
Proceed to
NEXT



NEXT

2.FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1605)
2.FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1605)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

d.

Read the DTCs.


Result:
Result Proceed to
P1605 is output A
P1605 and other DTCs are output B



A

3.DETERMINE CAUSE OF PROBLEM (CHECK FREEZE FRAME DATA)

B

3.DETERMINE CAUSE OF PROBLEM (CHECK FREEZE FRAME DATA)
a.

Determine the cause of the problem based on the freeze frame data recorded in Procedure 1.


Injection Feedback Val #1 (to #8):
Judgment of Data List Values Problem Cause Diagnosis Note
Any of Injection Feedback Val #1 to #8 in the freeze frame data is more than 3.0 mm3/st Fuel injector If the cylinder that displays Rough Idle ON also has a value of more than 3.0 mm3/st for Injection Feedback Val, there may be improper combustion in that cylinder.


Result:
Proceed to
NEXT



NEXT