Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT LEVELING SWITCH › from 2021.07
RM25T0E _59 Vehicle Exterior _029940 LIGHTING (EXT) _0138179 HEADLIGHT LEVELING SWITCH G

LIGHTING (EXT)  HEADLIGHT LEVELING SWITCH  INSPECTION  


PROCEDURE

Hide 84152 1.INSPECT HEADLIGHT LEVELING SWITCH

a.

Disconnect the headlight leveling switch connector.


b.
E362538C01
1.427,0.219 1.802,0.448 0.375,0.229 0.99,1.698 1.229,1.333 true 2.125,1.698 1.885,1.344 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 1.51,0.271 1.906,0.521 0.396,0.25 10 false L63 0.885,1.698 1.281,1.948 0.396,0.25 10 false B 2.156,1.75 2.552,2 0.396,0.25 10 false E
*a Front view of wire harness connector
(to Headlight Leveling Switch)


Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Measurement Condition Condition Specified Condition
L63-4(E) - Body ground Always Below 1 Ω


Standard Voltage:
Measurement Condition Condition Specified Condition
L63-1(B) - L63-4(E) Light control switch on 11 to 14 V


If the result is not as specified, repair or replace the wire harness or connector.


c.

Reconnect the headlight leveling switch connector.


d.

Turn the ignition switch to ON.


e.

Turn the light control switch head.


f.
E362549C01
1.531,0.198 1.885,0.406 0.354,0.208 0.927,1.021 1.344,1.021 true 1.833,1.01 1.833,0.542 1.833,0.542 2.396,0.542 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.604,0.24 1.969,0.5 0.365,0.26 10 false L63 0.802,0.958 1.167,1.219 0.365,0.26 10 false E 2.469,0.479 2.833,0.74 0.365,0.26 10 false RH 0
*a Component harness connected
(Headlight Leveling Switch)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Measurement Condition Condition
(Switch Position)
Specified Condition
L63-2(RH 0) - L63-4(E) 0 0.84 to 1.56 V
1 2.12 to 2.84 V
2 3.40 to 4.12 V
3 4.68 to 5.40 V
4 5.96 to 6.68 V
5 7.24 to 7.96 V


If the result is not as specified, replace the headlight leveling switch.


g.

Disconnect the automatic light control sensor connector.


h.

Check the illumination.

i.
E157014C03
0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Component without harness connected
(Headlight Leveling Switch)


Apply battery voltage to the connector and check the illumination conditions.

OK:
Measurement Condition Specified Condition
Battery positive (+) - 3
Battery negative (-) - 4
Illuminates


If the result is not as specified, replace the headlight leveling switch.