Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › MASS AIR FLOW METER(w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0290248 MASS AIR FLOW METER(w/ DPF) G

1VD-FTV ENGINE CONTROL  MASS AIR FLOW METER(w/ DPF)  INSPECTION  


PROCEDURE

Hide 22204 1.INSPECT MASS AIR FLOW METER

a.

Check the output voltage.

i.
A475069C01
2.781,1.667 2.833,1.25 2.833,1.25 2.917,1.25 true 2.135,2.375 2.135,2.208 2.135,2.208 2.646,1.698 true 1.813,1.292 1.979,1.292 1.979,1.292 2.5,1.677 true 2.958,1.156 3.406,1.385 0.448,0.229 10 false 1 (VG) 1.938,2.396 2.51,2.656 0.573,0.26 10 false 2 (E2G) 1.385,1.208 1.927,1.427 0.542,0.219 10 false 3 (+B) 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a
*a Component without harness connected
(Mass Air Flow Meter)
V100135

Air


Connect a battery positive (+) lead to terminal 3 (+B) and negative (-) lead to terminal 2 (E2G).

NOTICE:

While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.



ii.

Connect the positive (+) tester probe to terminal 1 (VG) and negative (-) tester probe to terminal 2 (E2G).


iii.

Blow air into the mass air flow meter and check that the voltage fluctuates.

OK:

The voltage changes.


If the result is not as specified, replace the mass air flow meter.



b.
A167890C07
0.802,0.958 1.063,0.958 1.063,0.958 1.333,1.458 true 1.594,1.469 1.823,0.958 1.823,0.958 2.146,0.958 true 1.344,1.448 1.448,1.594 0.104,0.146 10 false 5 1.5,1.448 1.604,1.594 0.104,0.146 10 false 4 1.656,1.448 1.76,1.594 0.104,0.146 10 false 3 1.958,1.448 2.063,1.594 0.104,0.146 10 false 1 1.802,1.448 1.906,1.594 0.104,0.146 10 false 2 2.188,0.875 2.604,1.073 0.417,0.198 10 false THA 0.594,0.875 0.854,1.052 0.26,0.177 10 false E2 0.063,0.052 0.24,0.219 0.177,0.167 10 false *a
*a Component without harness connected
(Mass Air Flow Meter)


Check the intake air temperature sensor (thermistor) resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (THA) - 5 (E2) Always 0.48 to 17.7 kΩ


If the result is not as specified, replace the mass air flow meter.