DESCRIPTION
When a pre-collision system DTC is stored, the forward recognition camera stores the current vehicle (ECU or sensor) state as Freeze Frame Data.
CHECK FREEZE FRAME DATA
Select a DTC to display the freeze frame data.
Check the freeze frame data for the output DTC.
FREEZE FRAME DATA CHART
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | - | - | - | Cannot be used |
| Total Distance Traveled - Unit | - | - | - | Cannot be used |
| PCS Function ON/OFF State | Pre-collision system on/off status | ON or OFF | ON: Pre-collision system on OFF: Pre-collision system off |
- |
| PBA Request | Pre-collision brake assist operation status | Not PBA Request, PBA Standby Request, PBA Request Level 1, PBA Request Level 2 | Not PBA Request: Pre-collision brake assist operation is not requested. PBA Standby Request: Pre-collision brake assist weak assist is requested. PBA Request Level 1: Pre-collision brake assist mild assist is requested. PBA Request Level 2: Pre-collision brake assist strong assist is requested. |
The value varies according to the possibility of a collision. The pre-collision brake assist request only indicates the status that the assist preparation is necessary. Whether or not the assist control is actually performed is dependent upon how the driver depresses the brake pedal. |
| VGRS Activation Request | - | - | - | Cannot be used |
| Warning Brake Request | - | - | - | Cannot be used |
| FPB Request | PCS brake request to skid control ECU (pre-collision braking) | ON or OFF | ON: Operating OFF: Not operating |
- |
| PB Request | Pre-collision brake operation status | ON or OFF | ON: Operating OFF: Not operating |
- |
| AVS Control Request | - | - | - | Cannot be used |
| Prefill | PCS brake operation preparation to skid control ECU | ON or OFF | ON: Operating OFF: Not operating |
- |
| PBR Request | PBR operation status | ON or OFF | ON: Operating OFF: Not operating |
- |
| PBH Request | PBH operation status | ON or OFF | ON: Operating OFF: Not operating |
PBH: Pre-collision brake hold |
| PCS PBA Invalid | Pre-collision brake assist function status | ON or OFF | ON: Pre-collision brake assist function invalid OFF: Pre-collision brake assist function valid |
- |
| PCS Warning Buzzer Invalid | PCS warning buzzer function status | ON or OFF | ON: PCS warning buzzer function invalid OFF: PCS warning buzzer function valid |
- |
| PCS PB Invalid | PCS brake function status | ON or OFF | ON: PCS brake function invalid OFF: PCS brake function valid |
- |
| Acceleration Suppression at Low Speed (A Control) Invalid | - | - | - | Cannot be used |
| Emergency Steering Assist Invalid 1 | - | - | - | Cannot be used |
| PCS Warning Display Request | PCS warning message status | Not Request, PCS Warning Display 1 Request, PCS Warning Display 2 Request, PCS Warning Display 3 Request | Not Request: Not displayed PCS Warning Display 1 Request: Displayed PCS Warning Display 2 Request: Not used PCS Warning Display 3 Request: Not used |
- |
| PCS Warning Buzzer Request | PCS meter buzzer operation status | ON or OFF | ON: PCS warning buzzer sounding OFF: PCS warning buzzer not sounding |
- |
| PCS Function ON/OFF State Stored | Storage condition of PCS ON/OFF condition when the PCS function is off and the ignition switch is turned from off to ON | Stored or Not Stored | Stored: Pre-collision system maintains off Not Stored: Pre-collision system always turns on |
"PCS Function ON/OFF State Stored" is a customizable item which can be set using the GTS. |
| PCS Warning Timing State Stored 2 | Storage condition of warning sensitivity setting when the PCS function is on and the ignition switch is turned from off to ON | Stored or Not Stored | Stored: Sensitivity settings are maintained as previous value Not Stored: Sensitivity is reset to default setting |
"PCS Function ON/OFF State Stored 2" is a customizable item which can be set using the GTS. |
| PCS Warning Timing State Stored 3 | Storage condition of warning sensitivity setting when the PCS function is off and the ignition switch is turned from off to ON | Stored or Not Stored | Stored: Sensitivity settings are maintained as previous value Not Stored: Sensitivity is reset to default setting |
"PCS Function ON/OFF State Stored 3" is a customizable item which can be set using the GTS. |
| PCS Warning Timing State Stored 1 | Storage condition of warning sensitivity setting when the PCS function is turned from off to on while the ignition switch is ON | Stored or Not Stored | Stored: Sensitivity settings are maintained as previous value Not Stored: Sensitivity is reset to default setting |
"PCS Function ON/OFF State Stored 1" is a customizable item which can be set using the GTS. |