FAIL-SAFE FUNCTION
When a malfunction occurs in the pre-collision system, the PCS warning light illuminates and the pre-collision system will be disabled depending on the malfunction.
| PCS Warning Light | Cause | DTC/RoB | Conditions to Return to Normal |
|---|---|---|---|
| Illuminate | Pre-collision system malfunction | C142571 | The system stops receiving stop light drive relay malfunction signals from the skid control ECU (brake actuator assembly) after turning the ignition switch from off to ON |
| Illuminate | Pre-collision system malfunction | U010087 | Communication with the ECM is restored to normal |
| Illuminate | Pre-collision system malfunction | U012587 | Communication with the yaw rate sensor returns to normal |
| Illuminate | Pre-collision system malfunction | U012687 | Communication with steering sensor is restored to normal |
| Illuminate | Pre-collision system malfunction | U012987 | Communication with the skid control ECU (brake actuator assembly) is restored to normal |
| Illuminate | Pre-collision system malfunction | U015587 | Communication with combination meter assembly returns to normal |
| Illuminate | Pre-collision system malfunction | U023587 | Communication with the millimeter wave radar sensor assembly is restored to normal |
| Illuminate | Pre-collision system malfunction | U023A87 | Communication with the skid control ECU (brake actuator assembly) is restored to normal |
| Illuminate | Pre-collision system malfunction | U030051 | Approximately 3 seconds or more elapse after the forward recognition camera judges the vehicle information sent from the ECM |
| Illuminate | Pre-collision system malfunction | U030057 | The vehicle information from the ECM and the information stored by the forward recognition camera match |
| Illuminate | Pre-collision system malfunction | U041881 | The system stops receiving brake control system malfunction signals from the skid control ECU (brake actuator assembly) after turning the ignition switch from off to ON |
| Illuminate | Pre-collision system malfunction | X2000 | The system stops receiving airbag ECU assembly malfunction signals from the skid control ECU (brake actuator assembly) or airbag ECU assembly after turning the ignition switch from off to ON |
| Illuminate | Pre-collision system malfunction | X2001 | The system stops receiving steering angle sensor malfunction signals from the steering sensor after the ignition switch is turned from off to ON |
| Illuminate | Pre-collision system malfunction | X2002 | The system stops receiving malfunction of the accelerator pedal position sensor signals from the ECM |
| Illuminate | Pre-collision system malfunction | X2003 | The system stops receiving electronically controlled brake system malfunction signals from the skid control ECU (brake actuator assembly) |
| Illuminate | Pre-collision system malfunction | X2011 | The forward recognition camera is no longer able to detect destination unconfirmed malfunctions |
| Illuminate | Pre-collision system malfunction | X2012 | The system is no longer able to detect forward recognition camera malfunctions after turning the ignition switch from off to ON |
| Illuminate | Pre-collision system malfunction | X2013 | The forward recognition camera is no longer able to detect camera axis misaligned malfunctions after turning the ignition switch from off to ON |
| Illuminate | Pre-collision system malfunction | X2014 | The forward recognition camera is no longer able to detect axis not adjusted malfunctions |
| Illuminate | Pre-collision system malfunction | X2018 | The forward recognition camera is no longer able to detect hot-wire heater malfunctions after turning the ignition switch from off to ON |
| Illuminate | Pre-collision system malfunction | X201D | The forward recognition camera is no longer able to detect destination malfunction signals |
| Illuminate | Pre-collision system malfunction | X2020 | The system stops receiving destination malfunction signals from the millimeter wave radar sensor assembly |
| Illuminate | Pre-collision system malfunction | X2021 | The system stops receiving malfunction signals from the millimeter wave radar sensor after turning the ignition switch from off to ON |
| Illuminate | Pre-collision system malfunction | X2022 | The system stops receiving axis misalignment signals from the millimeter wave radar sensor after turning the ignition switch from off to ON |
| Illuminate | Pre-collision system malfunction | X2023 | The system stops receiving beam axis not adjusted signals from the millimeter wave radar sensor assembly |
| Illuminate | Pre-collision system malfunction | X2070 | The system stops receiving forward recognition camera communication malfunction signals output from the millimeter wave radar sensor assembly |
| Illuminate | Millimeter wave radar sensor assembly axis is misaligned | X2025 | Millimeter wave radar sensor beam axis adjustment is completed and beam axis learning is completed |
| Illuminate | Foreign matter attached to millimeter wave radar sensor assembly | X2026 | Millimeter wave radar sensor assembly is cleaned |
| Illuminate | Millimeter wave radar sensor assembly temperature malfunction | X2027 | Millimeter wave radar sensor temperature returns to normal |
| Illuminate | Millimeter wave radar sensor assembly low voltage malfunction | X2028 | Millimeter wave radar sensor voltage returns to normal |
| Illuminate |
·
Windshield glass is dirty or fogged up
·
Forward recognition camera is dirty or fogged up |
X2015 | Forward recognition camera or area of windshield glass in front of forward recognition camera is cleaned |
| Illuminate | Outside of forward recognition camera guaranteed operating voltage | X2017 | Forward recognition camera voltage returns to normal |
| Illuminate | Forward recognition camera is temporarily unavailable (forward recognition camera recognition stopped) | X201F | After forward recognition camera returns to normal |
| Illuminate | Forward recognition camera temperature outside of operational range | X2016 | Forward recognition camera temperature returns to normal |