Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2022.09
RM25T0E _58 Vehicle Interior _128087 PRE-COLLISION _0548646 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U023587  Lost Communication with Cruise Control Front Distance Range Sensor Signal Sensor or Center Missing Message  


DESCRIPTION

The forward recognition camera communicates with the millimeter wave radar sensor assembly via CAN communication. If a communication malfunction between the forward recognition camera and millimeter wave radar sensor assembly is detected, DTC U023587 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
U023587 Lost Communication with Cruise Control Front Distance Range Sensor Signal Sensor or Center Missing Message Once 3 seconds elapse after turning the ignition switch to ON, a communication malfunction between the millimeter wave radar sensor assembly continues for approximately 2 seconds or more.
·

Harness or connector

·

Forward recognition camera

·

Millimeter wave radar sensor assembly



HINT:

If the DTCs are output simultaneously, the inspection area can be narrowed down.


Pattern DTC Output Part Name
(Display on GTS)
Suspected Area (Malfunction Status)
Forward Recognition Camera Millimeter Wave Radar Sensor Assembly
Pre-Collision System Front Radar Sensor
U023587 U010487

○: DTC is output

-: DTC is not output

Pattern 1 ○ ○ Harness or connector (Open or short)
Millimeter wave radar sensor assembly (Internal malfunction)
Forward recognition camera (Internal malfunction)
Pattern 2 ○ - Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)

WIRING DIAGRAM

C494250E01
0.75,1.906 3.042,2.385 2.292,0.479 10 false Forward Recognition Camera 4.823,1.896 6.219,2.656 1.396,0.76 10 false Millimeter Wave Radar Sensor Assembly 0.75,1.719 1.719,2.229 0.969,0.51 10 false S34*1, Y8*2 4.823,1.719 5.24,1.948 0.417,0.229 10 false I131 1.604,0.792 2.219,0.99 0.615,0.198 10 false CANH 1.615,1.469 2.229,1.667 0.615,0.198 10 false CANL 5.115,0.771 5.729,0.969 0.615,0.198 10 false CA1P 5.125,1.479 5.74,1.677 0.615,0.198 10 false CA1N 2.083,0.781 2.24,0.979 0.156,0.198 10 false 6 2.073,1.25 2.271,1.448 0.198,0.198 10 false 12 4.948,0.771 5.104,0.969 0.156,0.198 10 false 5 4.948,1.24 5.104,1.438 0.156,0.198 10 false 6 0.219,2.438 2.448,2.771 2.229,0.333 10 false *1: for Pickup 1.25,2.448 3.479,2.781 2.229,0.333 10 false *2: except Pickup

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history (RoB). Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.

HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target: Click hereVehicle Interior>PRE-COLLISION>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target: Click hereVehicle Interior>PRE-COLLISION>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment: Click hereVehicle Interior>PRE-COLLISION>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT


·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history (RoB) for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereVehicle Interior>PRE-COLLISION>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereVehicle Interior>PRE-COLLISION>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereVehicle Interior>PRE-COLLISION>FRONT CAMERA>DRIVING ADJUSTMENT


·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

·

When disconnecting and reconnecting the battery

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK FOR DTCs
a.

Read each DTC and check the diagnosis pattern using the table below.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432
Body Electrical > Front Radar Sensor > Trouble Codes
50001 429
Pattern DTC Output Part Name
(Display on GTS)
Pre-Collision System Front Radar Sensor
Pattern 1 U023587 U010487
Pattern 2 U023587 -


Result:
Result Proceed to
Pattern 1 A
Pattern 2 B



A

2.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)

B

4.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
2.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the S34*1 or Y8*2 forward recognition camera connector.

*1: for Pickup

*2: except Pickup



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Pickup
Tester Connection Condition Specified Condition
S34-6 (CANH) - S34-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
S34-6 (CANH) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
S34-12 (CANL) - Body ground
S34-6 (CANH) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
S34-12 (CANL) - +B

except Pickup
Tester Connection Condition Specified Condition
Y8-6 (CANH) - Y8-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
Y8-6 (CANH) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
Y8-12 (CANL) - Body ground
Y8-6 (CANH) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Y8-12 (CANL) - +B


Result:
Proceed to
OK
NG




OK

REPLACE FORWARD RECOGNITION CAMERA

NG

3.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
3.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Connect the S34*1 or Y8*2 forward recognition camera connector.

*1: for Pickup

*2: except Pickup



b.

Disconnect the I131 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I131-5 (CA1P) - I131-6 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
I131-5 (CA1P) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I131-6 (CA1N) - Body ground
I131-5 (CA1P) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I131-6 (CA1N) - +B


Result:
Proceed to
OK
NG




OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Disconnect the S34*1 or Y8*2 forward recognition camera connector.

*1: for Pickup

*2: except Pickup



b.

Using an oscilloscope, check the waveform.

OK:
for Pickup
Tester Connection Condition Tool Setting Specified Condition
S34-6 (CANH) - S34-12 (CANL) Ignition switch ON 1V/DIV., 100μs/DIV. Pulse generation

except Pickup
Tester Connection Condition Tool Setting Specified Condition
Y8-6 (CANH) - Y8-12 (CANL) Ignition switch ON 1V/DIV., 100μs/DIV. Pulse generation


Result:
Proceed to
OK
NG




OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY