TROUBLESHOOTING PRECAUTIONS
When there are malfunctions with terminal contact points or part installation problems, removal and installation of the suspected problem parts may return the system to the normal condition either completely or temporarily.
In order to determine the malfunctioning area, check the conditions at the time the malfunction occurred, such as DTC output and the Freeze Frame Data, and record them before disconnecting each connector or removing and installing parts.
Since the system may be influenced by malfunctions in systems other than the VSC system, be sure to check for DTCs in other systems.
HANDLING PRECAUTION
Do not remove or install VSC parts such as the steering sensor or yaw rate and acceleration sensor (airbag ECU assembly) except when required, as they need to be adjusted correctly after removal and installation.
Be sure to perform preparation before work and confirmation after work is completed by following the directions in the repair manual when working on the vehicle stability control system.
Be sure to remove and install the ECU, brake actuator assembly, sensors, etc. with the ignition switch off unless otherwise specified in the inspection procedure.
If the ECU, brake actuator assembly or a sensor has been removed and installed, it is necessary to check the system for problems after the parts have been reassembled. Check for DTCs using the GTS. Also check that the system functions and signals received by the ECU are normal using "Signal Check".
If replacing the skid control ECU (brake actuator assembly), always replace it with a new one (if the skid control ECU (brake actuator assembly) is not replaced with a new one, DTCs may be stored).
Do not use a skid control ECU (brake actuator assembly) from another vehicle (a vehicle display model, etc.).
DTC PRECAUTION
Some DTCs cannot be cleared only by repairing the malfunctioning parts.
To turn off the warning (light illuminated), clear the DTC or perform the operation below.
| DTC No. | Procedure |
|---|---|
| C05001F C050023 C05061F C050623 C050C1F C050C23 C05121F C051223 C05201C C052096 |
1.
Repair or replace with new part
2.
Turn ignition switch to ON
3.
Drive (30 km/h or higher for 30 seconds) → Warning light turns off |
| P057111 |
1.
Repair or replace with new part
2.
Turn the ignition switch to ON and stop the vehicle for 5 seconds or more, and then lightly depress the brake pedal 2 or 3 times → Warning light turns off |
| C052696 C14FE14 |
1.
Repair or replace with new part
2.
Turn ignition switch to ON after idling for 3 seconds → Warning light turns off |
| C006396 |
1.
Repair or replace with new part
2.
Turn ignition switch to ON after idling for 10 seconds → Warning light turns off |
When a warning is output (light illuminated), the fail-safe function prevents system operation. Take due care when driving or braking.
Even after the DTC is cleared, the DTC will be stored again if the malfunction continues.
When 2 or more DTCs are detected, perform diagnosis for each DTC, one by one until the problem is identified.
CHASSIS DYNAMOMETER PRECAUTION
When testing with a 2-wheel drum tester such as a speedometer tester, combination tester for the speedometer and brakes, or chassis dynamometer, or when jacking up the front wheels and turning the wheels, perform the following procedure to enter Inspection Mode and disable the TRC and VSC systems.
Do not use the drum tester with any of the lock chains disconnected.
Using the drum tester with a lock chain disconnected could cause the vehicle to begin moving unexpectedly.
Do not use the drum tester while the TRC or VSC is able to operate.
TRC or VSC operation could cause the vehicle to begin moving unexpectedly.
Secure the vehicle with lock chains for safety.
If Inspection Mode is not used, the vehicle may unexpectedly move off the dynamometer because of TRC and VSC operation.
The VSC OFF switch must not be used to disable TRC and VSC operation when the vehicle is to be operated on a dynamometer. Pressing the VSC OFF switch does not disable TRC and VSC operation completely.
Activating Inspection Mode (When Using the GTS)
Ensure that the ignition switch is off and the engine is stopped.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Brake / Utility / Inspection Mode.
| Tester Display |
|---|
| Inspection Mode |
Check that the TRC OFF and VSC OFF indicator lights come on.
If the TRC OFF and VSC OFF indicator lights in the combination meter do not come on, repeat the steps above.
Using the GTS to cancel Inspection Mode causes the system to enter normal mode.
Activating Inspection Mode (When not Using the GTS)
Perform steps "D" to "H" within 30 seconds.
Turn the ignition switch to ON (Step "A").
Release the parking brake (Step "B").
Turn the ignition switch off (Step "C").
With the brake pedal depressed, start the engine (Step "D").
While holding the brake pedal down, apply the parking brake (Step "E").
With the parking brake applied, release and depress the brake pedal twice: release→depress→release→depress (Step "F").
While holding the brake pedal down, release and apply the parking brake twice: release→apply→release→apply (Step "G").
With the parking brake applied, release and depress the brake pedal twice: release→depress→release→depress (Step "H").
except Multi-information Display Type:
Check that the TRC OFF and VSC OFF indicator lights come on (Step "I").
Turn the ignition switch off when 60 seconds or more have elapsed since inspection mode was entered. If the ignition switch is turned off before 60 seconds or more elapse, inspection mode continues when the ignition switch is turned to ON.
If the TRC OFF and VSC OFF indicator lights do not come on in step "I", repeat steps "A" to "I".
Turning the ignition switch off ends Inspection Mode.
CAN COMMUNICATION SYSTEM PRECAUTIONS
The CAN communication system is used for data communication among the skid control ECU (brake actuator assembly), the steering sensor, the yaw rate and acceleration sensor (airbag ECU assembly) and other ECUs. If there is trouble in the CAN communication line, corresponding communication line DTCs are output.
If any CAN communication line DTC is output, repair the malfunction in the communication line and troubleshoot the VSC system after data communication becomes normal.
In order to enable CAN communication, a specific type of wiring is used for the CAN communication lines. The wiring used for each communication line is a twisted pair of wires of equal length. A bypass wire should not be used because the data being transmitted will be corrupted.