Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  TERMINALS OF ECU  


CHECK BRAKE ACTUATOR ASSEMBLY


a.

Disconnect the A45 connector and measure the voltage or resistance on the wire harness side.

C425606C41
1.219,0.677 1.656,0.969 0.438,0.292 0.25,0.208 0.563,0.406 0.313,0.198 10 false *a 1.281,0.75 1.74,0.958 0.458,0.208 10 false A45
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])
- -


HINT:

Voltage cannot be measured with the connector connected to the skid control (brake actuator assembly) as the connector is watertight.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
A45-1 (GND1) - Body ground No. 2 skid control ECU (brake actuator assembly) ground 1 minute or more after disconnecting the cable from the negative (-) battery terminal Below 1 Ω
A45-2 - - -
A45-3 - - -
A45-4 (RL-) Rear speed sensor LH (-) signal input - -
A45-5 (RL+) Rear speed sensor LH (+) power supply output - -
A45-6 (FR-) Front speed sensor RH (-) signal input - -
A45-7 (FR+) Front speed sensor RH (+) power supply output - -
A45-8 - - -
A45-9 (CSW) - Body ground VSC OFF switch input VSC OFF switch is pushed → released Below 1 Ω → 10 kΩ or higher
A45-10 - - -
A45-11 (STP) - Body ground Stop light switch assembly input Stop light switch assembly on → off (Brake pedal depressed → released) 11 to 14 V → Below 1.5 V
A45-12 - - -
A45-13 - - -
A45-14 (+BS) - Body ground Solenoid relay power supply Always 11 to 14 V
A45-15 (HDCS) Pull up terminal for L4 position switch (No. 1 transfer indicator switch) - -
A45-16 - - -
A45-17 - - -
A45-18 (SP1) Speed sensor signal output - -
A45-19 (RR-) Rear speed sensor RH (-) signal input - -
A45-20 (RR+) Rear speed sensor RH (+) power supply output - -
A45-21 (FL-) Front speed sensor LH (-) signal input - -
A45-22 (FL+) Front speed sensor LH (+) power supply output - -
A45-23 (EXI4) L4 position switch (No. 1 transfer indicator switch) input - -
A45-24 - - -
A45-25 - - -
A45-26 - - -
A45-27 (CANH) CAN communication line (H) - -
A45-28 (FSW+) Pull up terminal for rear differential lock position switch (No. 4 transfer indicator switch) - -
A45-29 - - -
A45-30 (GND2) - Body ground Pump motor ground 1 minute or more after disconnecting the cable from the negative (-) battery terminal Below 1 Ω
A45-31 - - -
A45-32 (STPO) - Body ground Stop light control relay (STP LP relay) output Always 11 to 14 V
A45-33 (EXI3) Rear differential lock position switch (No. 4 transfer indicator switch) signal input - -
A45-34 - - -
A45-35 (EXI) Center differential lock position switch (No. 1 transfer indicator switch) input - -
A45-36 - - -
A45-37 (STP2) - Body ground Stop light control relay (STP LP relay) input Stop light switch assembly on → off (Brake pedal depressed → released) 11 to 14 V → Below 1.5 V
A45-38 - - -
A45-39 - - -
A45-40 - - -
A45-41 - - -
A45-42 - - -
A45-43 (CANL) CAN communication line (L) - -
A45-44 - - -
A45-45 (IG1) - Body ground ECU power supply input Ignition switch ON 11 to 14 V
A45-46 (BM) - Body ground Motor relay power supply Always 11 to 14 V