Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2021.12
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM U

1GR-FE ENGINE CONTROL  SFI SYSTEM  FAIL-SAFE CHART  


If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily.

DTCs Component Fail-Safe Operation Fail-Safe Deactivation Condition
P0011, P0021 VVT system
·

Idle up (control of combustion worsening).

·

Fuel-cut control is stopped.


Pass condition detected
P0031, P0032, P0051, P0052, P101D and P103D Air fuel ratio sensor heater The ECM turns off the A/F sensor heater. Ignition switch off
P0037, P0038, P0057, P0058, P102D and P105D Heated oxygen sensor heater The ECM turns off the heated oxygen sensor heater. Ignition switch off
P0102, P0103 Mass air flow meter The ECM calculates the ignition timing according to the engine speed and throttle valve position. Pass condition detected
P0112, P0113 Intake air temperature sensor The ECM estimates the intake air temperature to be 20°C (68°F). Pass condition detected
P0115, P0117 and P0118 Engine coolant temperature sensor The ECM estimates the engine coolant temperature to be 80°C (176°F). Pass condition detected
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060D, P060E, P0657, P2102, P2103, P2111, P2112, P2118, P2119 and P2135 Electronic Throttle Control System (ETCS) The ECM cuts off the throttle actuator current and the throttle valve returns to 6° throttle position by the return spring.
The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at minimal speed.*1
Pass condition detected and then ignition switch turned off
P0300, P0301, P0302, P0303, P0304, P0305 and P0306
*2
·

Fuel injector assembly

·

Electronic throttle control system


When a catalyst-damaging misfire occurs (MIL blinking), the following fail-safe operation is performed for catalyst overheat malfunction prevention.
1.

Under a low load and at a low engine speed:

- Fuel-cut is performed on the malfunctioning cylinder.

2.

Under a high load and at a high engine speed:

- Throttle valve opening angle control is performed.

- Fuel-cut is performed on all cylinders or the malfunctioning cylinder.


Pass condition detected and then ignition switch turned off
P0327, P0328, P0332 and P0333 Knock Sensor The ECM sets the ignition timing to maximum retard. Ignition switch off
P0351 to P0356 Ignition coil assembly The ECM cuts the fuel. Pass condition detected
P0504 Stop light switch assembly The accelerator pedal opening angleis fixed when there is a acceleratorpedal malfunction or history of a malfunction Pass condition detected
P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138 Accelerator pedal position sensor The accelerator pedal position sensor has 2 sensor circuits: Main and Sub.
If either circuit malfunctions, the ECM limits the engine output.
If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.
Pass condition detected and then ignition switch turned off
P2237, P2238, P2239, P2240, P2241, P2242, P2243, P2252, P2253, P2255 and P2256 Air fuel ratio sensor
·

Air fuel ratio feedback controlis stopped.

·

Current to the air fuel ratio sensor heater is cut.


Pass condition detected and then ignition switch turned off

HINT:

*1: The vehicle can be driven slowly if the accelerator pedal is depressed firmly and slowly. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.

*2: Misfire-related fail-safe operations occur when catalyst overheat malfunctions occur.