CHECK COMBINATION METER ASSEMBLY
Measure the voltage and resistance and check for pulses according to the value(s) in the table below.
| *A | for 12 V Battery Type | - | - |
| Terminal No. | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: w/o VSC *2: w/ VSC *3: w/ Front Fog Light *4: w/ Rear Fog Light *5: for 1VD-FTV *6: for 1GR-FE *7: w/o ABS *8: w/ Differential Lock *9: w/ Airbag System *10: w/o Airbag System *11: for 1HZ *12: w/ ABS *13: w/ Seat Belt Warning System *14: w/ Passenger Seat Belt Warning System *15: w/ Oil Pressure Warning Light *16: for Sub Fuel Tank *17: for Main Tank *18: for Double Tank Type *19: w/ Immobiliser System *20: w/ Oil Pressure Gauge *21: w/ Key Reminder Warning System *22: for 12 V Battery Type *23: for 24 V Battery Type *24: w/ Tire Pressure Warning System *25: 1VD-FTV (w/o DPF) *26: for LHD *27: for RHD *28: w/ Pre-Collision System |
||||
| L25-1 (FOG) - Body ground*3 | B - Body ground | FRONT FOG indicator light signal | Ignition switch ON, front fog indicator light on | 11 to 14 V |
| Ignition switch ON, front fog indicator light off | Below 1 V | |||
| L25-2 (SW) - Body ground | L - Body ground | 4WD indicator light signal | Ignition switch ON, 4WD indicator light on | Below 1 V |
| Ignition switch ON, 4WD indicator light off | 11 to 14 V*22 20 to 28 V*23 |
|||
| L25-3 (+) - Body ground*4 | GR - Body ground | REAR FOG indicator light signal | Ignition switch ON, rear fog indicator light on | 11 to 14 V |
| Ignition switch ON, rear fog indicator light off | Below 1 V | |||
| L25-4 (ILL+) - Body ground | G - Body ground | Illumination light signal | Light control switch off | Below 1 V |
| Light control switch TAIL or HEAD | 11 to 14 V*22 20 to 28 V*23 |
|||
| L25-6 (DOOR) - Body ground | GR - Body ground | Driver side door opening signal | Driver side door is open | Below 1 V |
| Driver side door is closed | 11 to 14 V*22 20 to 28 V*23 |
|||
| L25-7 (SW) - Body ground | B - Body ground | DOOR warning light signal | A door is open | Below 1 V |
| All door are closed | 11 to 14 V*22 20 to 28 V*23 |
|||
| L25-8 (+S) - Body ground | G - Body ground | Speed signal (output) | Driving at approximately 20 km/h (12 mph) | Pulse generation (See waveform 1) |
| L25-9 (SI) - Body ground | R - Body ground | Speed signal (input) | Driving at approximately 20 km/h (12 mph) | Pulse generation (See waveform 2) |
| L25-10 (S) - Body ground*1 | B - Body ground | Tachometer signal | Engine idling | Pulse generation |
| L25-11 (OIL) - Body ground*5 | V - Body ground | Engine oil level signal | Ignition switch ON, engine oil level low | 11 to 14 V |
| Ignition switch ON, engine oil level not low | Below 1 V | |||
| L25-12 (CHK) - Body ground*1*5,*1*6 | W - Body ground*26 P - Body ground*27 |
MIL indicator light signal | Ignition switch ON, MIL indicator light signal on | Below 1 V |
| Ignition switch ON, MIL indicator light signal off | 11 to 14 V | |||
| L25-13 (IG+) - Body ground*7 | L - Body ground | Speed sensor power supply | Ignition switch ON | 11 to 14 V*22 20 to 28 V*23 |
| Ignition switch off | Below 1 V | |||
| L25-13 (TX1+) - L25-12 (TX1-)*28 | L - W | Ambient temperature sensor signal | Ignition switch ON | 4.4 to 5.6 V |
| L25-14 (+) - Body ground | P - Body ground | HI BEAM indicator light signal | High beam indicator light on | 11 to 14 V*22 20 to 28 V*23 |
| High beam indicator light off | Below 1 V | |||
| L25-15 (ES) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
| L25-16 (FRSW) - Body ground*8 | Y - Body ground | Front differential lock indicator light signal | Ignition switch ON, front differential lock indicator light on | Below 1 V |
| Ignition switch ON, front differential lock indicator light off | 11 to 14 V*22 20 to 28 V*23 |
|||
| L25-17 (RRSW) - Body ground*8 | SB - Body ground | Rear differential lock indicator light signal | Ignition switch ON, rear differential lock indicator light on | Below 1 V |
| Ignition switch ON, rear differential lock indicator light off | 11 to 14 V*22 20 to 28 V*23 |
|||
| L25-18 (A/B) - Body ground*1 | R - Body ground | SRS warning light signal*9 | Ignition switch ON, SRS warning light off | 11 to 14 V |
| Ignition switch ON, SRS warning light on | Below 1 V | |||
| Battery*10 | Always | 11 to 14 V | ||
| L25-19 (LP) - Body ground*1 | V - Body ground | Ground*7 | Always | Below 1 Ω |
| ABS warning light signal*12 | Ignition switch ON, ABS warning light on | 11 to 14 V | ||
| Ignition switch ON, ABS warning light off | Below 1 V | |||
| L25-20 (GLW-) - Body ground*1*5,*11 | R-W - Body ground*1*5 G - Body ground*11 |
GLOW warning light signal | Glow indicator warning light on | Below 1 V |
| Glow indicator warning light off | 11 to 14 V*22 20 to 28 V*23 |
|||
| L25-21 (SW) - Body ground*13 | P - Body ground | Seat belt warning light signal | Ignition switch ON, driver side seat buckle switch is fastened | 11 to 14 V |
| Ignition switch ON, driver side seat buckle switch is unfastened | Below 1 V | |||
| L25-22 (P/SB) -Body ground*14 | G - Body ground | Front passenger seat belt buckle switch signal | Ignition switch ON, front passenger seat occupied and front passenger side seat belt unfastened | 11 to 14 V |
| Ignition switch ON, front passenger seat occupied and front passenger side seat belt fastened | Below 1 V | |||
| L25-23 (S) - Body ground*5,*11 | GR - Body ground | Fuel sediment switch signal | Ignition switch ON, fuel sediment switch on | Below 1 V |
| Ignition switch ON, fuel sediment switch off | 11 to 14 V*22 20 to 28 V*23 |
|||
| L25-24 (FFTR) - Body ground*25 | W - Body ground | Fuel filter clogging switch signal | Ignition switch ON, fuel filter clogging switch on | 11 to 14 V |
| Ignition switch ON, fuel filter clogging switch off | Below 1 V | |||
| L25-25 (S) - Body ground*1,*6 | G - Body ground | Engine coolant temperature sensor signal | Engine running, engine coolant temperature 80°C (176°F) | Pulse generation (See waveform 3) |
| L25-26 (B) - Body ground | R - Body ground | Battery | Always | 11 to 14 V*22 20 to 28 V*23 |
| L25-27 (BRL) - Body ground*5,*11 | G - Body ground | Vacuum warning switch signal | Ignition switch ON, vacuum warning switch on | Below 1 V |
| Ignition switch ON, vacuum warning switch off | 11 to 14 V*22 20 to 28 V*23 |
|||
| L25-28 (B) - Body ground | V - Body ground | Ignition switch signal | Ignition switch ON | 11 to 14 V*22 20 to 28 V*23 |
| Ignition switch off | Below 1 V | |||
| L26-1 (CHG-) - Body ground | P - Body ground | CHARGE warning light signal | Ignition switch ON, CHARGE warning light on | Below 1 V |
| Ignition switch ON, CHARGE warning light off | 11 to 14 V*22 20 to 28 V*23 |
|||
| L26-2 (SW) - Body ground | V - Body ground | Fluid level warning switch signal | Ignition switch ON, brake fluid level low | Below 1 V |
| Ignition switch ON, brake fluid level not low | 11 to 14 V | |||
| L26-3 (OIL1) - Body ground*15 | SB - Body ground | Engine oil pressure switch signal | Ignition switch ON, oil pressure warning light on | Below 1 V |
| Ignition switch ON, oil pressure warning light off | 11 to 14 V*22 20 to 28 V*23 |
|||
| L26-4 (FE) - Body ground*16 | G - Body ground | Sub fuel sender gauge ground | Always | Below 1 Ω |
| L26-5 (FE) - Body ground*17 | BR - Body ground | Main fuel sender gauge ground | Always | Below 1 Ω |
| L26-6 (FV) - Body ground*16 | BR - Body ground | Sub fuel sender gauge power source | Ignition switch ON | 4.75 to 5.25 V |
| Ignition switch off | Below 1 V | |||
| L26-7 (FV) - Body ground*17 | B - Body ground | Main fuel sender gauge power source | Ignition switch ON | 4.75 to 5.25 V |
| Ignition switch off | Below 1 V | |||
| L26-8 (IND) - Body ground*18 | R - Body ground | SUB indicator light signal | Ignition switch ON, SUB indicator light on | Below 1 V |
| Ignition switch ON, SUB indicator light off | 11 to 14 V | |||
| L26-9 (FR) - Body ground*16 | P - Body ground | Sub fuel receiver gauge assembly signal | Ignition switch ON, fuel F (full tank) | 4.25 to 4.61 V |
| Ignition switch ON, E (empty) | 0.34 to 0.70 V | |||
| L26-10 (FR) - Body ground*17 | R - Body ground | Main fuel receiver gauge assembly signal | Ignition switch ON, fuel F (full tank) | 4.25 to 4.61 V |
| Ignition switch ON, E (empty) | 0.34 to 0.70 V | |||
| L26-11 (LP) - Body ground*19 | L - Body ground | SECURITY warning light signal | Immobiliser unset | Below 1 V |
| Immobiliser set | 11 to 14 V ←→ Below 1 V | |||
| L26-13 (CANH) - Body ground*2 | G - Body ground | CAN communication line | - | - |
| L26-14 (CANL) - Body ground*2 | W - Body ground | CAN communication line | - | - |
| L26-15 (BLP) -Body ground*13 | L - Body ground | Back-up light switch signal | Ignition switch ON, back-up light switch on | 11 to 14 V |
| Ignition switch ON, back-up light switch off | Below 1 V | |||
| L26-16 (IG+) - Body ground*6,*20 | B - Body ground | Oil pressure sensor power source | Ignition switch ON | 4.75 to 5.25 V |
| L26-17 (S) -Body ground*6,*20 | L - Body ground | Oil pressure sensor gauge signal | Ignition switch off | Below 1 V |
| Ignition switch ON | 0 to 5 V | |||
| L26-18 (SW) - Body ground*21 | R - Body ground | Unlock warning switch signal | No key in ignition key cylinder | Below 1 V |
| Ignition switch off, key in ignition key cylinder | 11 to 14 V | |||
| L26-19 (FR) - Body ground*1,*5,*11 | P - Body ground | Engine coolant temperature sensor signal | Engine is warmed up: Idling, engine coolant temperature at 60 to 120°C (140 to 248°F)*5 | 3 to 1 V |
| Engine is warmed up: Idling, engine coolant temperature at 80°C (176°F)*11 | Approximately 2.4 V | |||
| L26-20 (PKBI) - Body ground | W - Body ground | Parking brake switch assembly signal | Ignition switch ON, parking brake switch on | Below 1 V |
| Ignition switch ON, parking brake switch off | 11 to 14 V*22 20 to 28 V*23 |
|||
| L26-21 (S) - Body ground*20 | SB - Body ground | Oil pressure sender gauge signal | Ignition switch off | Below 1 V |
| Ignition switch ON | 4.3 to 15.2 V | |||
| L26-22 (B) - Body ground | V - body ground*23 W - body ground*22 |
Turn signal indicator LH signal (input) | Ignition switch ON, turn signal light switch position is left | Below 1 V ←→ 20 to 28 V*23 Below 1 V*22 |
| Ignition switch ON, turn signal light switch position is not left | Below 1 V*23 11 to 14 V*22 |
|||
| L26-23 (B) - Body ground | G - Body ground | Turn signal indicator RH signal (input) | Ignition switch ON, turn signal light switch position is right | Below 1 V ←→ 20 to 28 V*23 Below 1 V*22 |
| Ignition switch ON, turn signal light switch position is not right | Below 1 V*23 11 to 14 V*22 |
|||
| L26-24 (E) - Body ground*6,*20 | W-B - Body Ground | Oil pressure sensor gauge ground | Always | Below 1 Ω |
| L50-1 (HZSW) - Body ground*22 | R - Body ground | Hazard warning switch signal | Hazard warning signal switch off | 11 to 14 V |
| Hazard warning signal switch on | Below 1 V | |||
| L50-2 (B) - Body ground*22 | G - Body ground | Battery | Always | 11 to 14 V |
| L50-4 (LR) - Body ground*22 | Y - Body ground | Turn signal indicator RH signal (output) | Ignition switch ON, RH turn indicator light off | Below 1 V |
| Ignition switch ON, RH turn indicator light blinking | 11 to 14 V ←→ Below 1 V | |||
| L50-6 (LL) - Body ground*22 | GR - Body ground | Turn signal indicator LH signal (output) | Ignition switch ON, LH turn indicator light off | Below 1 V |
| Ignition switch ON, LH turn indicator light blinking | 11 to 14 V ←→ Below 1 V | |||
| L25-5 (TIRE) - Body ground*24 | P - Body ground | Tire pressure warning light signal | Ignition switch ON, tire pressure warning light off | 3.2 V or higher |
| Ignition switch ON, tire pressure warning light blinks | Below 3.2 V | |||
Using an oscilloscope, check waveform 1.
| Item | Condition |
|---|---|
| Tester Connection | L25-8 (+S) - Body ground |
| Tool Setting | 2 V/DIV., 20 msec./DIV. |
| Condition | Driving at approximately 20 km/h (12 mph) |
As the vehicle speed increases, the wavelength shortens.
Using an oscilloscope, check waveform 2.
| Item | Condition |
|---|---|
| Tester Connection | L25-9 (SI) - Body ground |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Driving at approximately 20 km/h (12 mph) |
As the vehicle speed increases, the wavelength shortens.
Using an oscilloscope, check waveform 3.
| Item | Condition |
|---|---|
| Tester Connection | L25-25 (S) - Body ground |
| Tool Setting | 5 V/DIV., 10 msec./DIV. |
| Condition | Engine running, engine coolant temperature 80°C (176°F) |
As the coolant temperature rises, the period "A" shown in the illumination becomes longer.