Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0556385 CAN COMMUNICATION SYSTEM(w/ Pre-collision System) D

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Pre-collision System)  DIAGNOSIS SYSTEM  


CAN BUS CHECK


HINT:

The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the GTS.


a.

Using the GTS, select the CAN Bus Check screen.

NOTICE:
·

It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)

·

In the bus selection pull down menu, all buses applicable to the model are displayed (e.g. LIN communication buses are also displayed). Therefore, refer to the wiring diagrams to check the names of sub buses for CAN communication.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>SYSTEM DIAGRAM



HINT:

Different connection statuses are indicated by the background color of ECUs and sensors that are displayed.

Explanation of CAN Bus Check Screen
Bus Type Background Color Connection Status
Bus White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*4

·

No ECUs or sensors are connected to the bus.*5


Sub bus with a gateway function equipped ECU that does not memorize connected ECUs or sensors*2 White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus with a gateway function equipped ECU that memorizes connected ECUs and sensors*3 White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The gateway function equipped ECU cannot communicate with the central gateway ECU.*6

·

No ECUs or sensors are connected to the sub bus.*7



·

Gateway function equipped ECUs relay signals between ECUs and sensors connected to different buses.

·

*1: An ECU or sensor is installed to the vehicle but is not displayed on the "Communication Bus Check" screen.

·

*2: The gateway function equipped ECU does not memorize ECUs and sensors connected to its respective sub bus.

·

*3: The gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus.

·

*4: When the central gateway ECU has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.

·

*5: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.

·

*6: When a gateway function equipped ECU cannot communicate with the central gateway ECU, the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.

·

*7: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.

·

If there is no communication between the GTS and the vehicle, or no ECUs or sensors are displayed as connected, check the central gateway ECU and V bus (the bus that connects the DLC3 to the central gateway ECU) for malfunctions.




b.

Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.

HINT:
·

If an open occurs in one of the lines of a CAN branch (except DLC3), output from the other branch line (the line that is not open) will be unstable and it may interfere with the response (display) of other ECUs and sensors.

·

If the connection status changes during the inspection, repair the open in the branch line of the ECU or sensor that does not respond (is not detected) and then perform the CAN bus check again.





HOW TO INTERPRET CAN BUS CHECK SCREEN


a.

When a communication stop is currently occurring, the probable malfunctioning part can be determined from the CAN bus check and by using the following methods.

NOTICE:

The following CAN bus wiring diagram is provided only as an example. This wiring diagram is different from the actual wiring diagram for this vehicle.


HINT:
·

When a communication stop is currently occurring, it is easier to determine the probable malfunctioning part from the CAN bus check rather than from communication DTCs.

·

Wait for approximately 2 minutes after turning the ignition switch to ON (or simulate the driving conditions that enable the malfunction to be reproduced) and select "CAN Bus Check". Then observe the communication status of each ECU on the screen.




b.

If a communication error of only 1 ECU or sensor is indicated on the CAN Bus Check screen, a communication stop of the ECU or sensor is suspected.

Open in both CAN branch lines of HV on the bus 4

C360877C01
6.292,6.135 6.604,6.333 0.313,0.198 10 false *f 1,1.115 1.313,1.313 0.313,0.198 10 false *a 1.01,2.292 1.323,2.49 0.313,0.198 10 false *b 1.708,3.542 2.021,3.74 0.313,0.198 10 false *c 5.479,0.625 5.792,0.823 0.313,0.198 10 false : *e 1.021,4.438 1.333,4.635 0.313,0.198 10 false *d 0.448,2.542 1.292,2.781 0.844,0.24 10 false CGW 2.063,0.719 2.906,0.958 0.844,0.24 10 false F-MGC 3.75,0.719 4.594,0.958 0.844,0.24 10 false HVB 4.302,0.719 5.146,0.958 0.844,0.24 10 false R-MGC 1.948,1.302 2.792,1.542 0.844,0.24 10 false CAN J/C 1 3.865,1.302 4.708,1.542 0.844,0.24 10 false CAN J/C 2 6.406,1.302 6.906,1.542 0.5,0.24 10 false ENG 1.865,1.885 2.708,2.125 0.844,0.24 10 false HV 2.438,1.875 3.281,2.115 0.844,0.24 10 false BRK 1.958,2.469 2.802,2.708 0.844,0.24 10 false CAN J/C 3 3.896,2.469 4.74,2.708 0.844,0.24 10 false CAN J/C 4 5.719,2.469 6.219,2.698 0.5,0.229 10 false SRS 1.844,3.125 2.344,3.354 0.5,0.229 10 false MB 3.76,3.073 4.26,3.302 0.5,0.229 10 false EPS 4.385,3.073 4.885,3.302 0.5,0.229 10 false STR 2.917,3.906 3.76,4.146 0.844,0.24 10 false CAN J/C 5 4.813,3.906 5.656,4.146 0.844,0.24 10 false CAN J/C 6 6.458,3.906 6.771,4.146 0.313,0.24 10 false ST 1.531,4.573 2.031,4.802 0.5,0.229 10 false DLC3 3.052,4.51 3.552,4.74 0.5,0.229 10 false MIR-R 4.979,4.51 5.479,4.74 0.5,0.229 10 false MIR-L
*a Bus 2 *b Bus 4
*c Sub Bus *d V Bus
*e Location of Malfunction *f Background color is red


HINT:

When there are communication stops, ECUs that are present in the vehicle may not be displayed on the CAN Bus Check screen.



c.

If communication errors for multiple ECUs or sensors are indicated on the CAN Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or sensor whose background color is red) is suspected.

Example: Open in a CAN branch line for HV on the bus 4

C360878C01
6.365,1.135 6.677,1.333 0.313,0.198 10 false *a 6.354,1.625 6.667,1.823 0.313,0.198 10 false *c 0.708,1.771 1.021,1.969 0.313,0.198 10 false *c 0.708,1.198 1.021,1.396 0.313,0.198 10 false *b
*a Background color is red *b Background color intermittently becomes yellow or red
*c Not displayed or background color is yellow or red - -


Explanation of CAN Bus Check Screen
Bus Type Background Color Connection Status
Bus White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*4

·

No ECUs or sensors are connected to the bus.*5


Sub bus with a gateway function equipped ECU that does not memorize connected ECUs or sensors*2 White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus with a gateway function equipped ECU that memorizes connected ECUs and sensors*3 White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The gateway function equipped ECU cannot communicate with the central gateway ECU.*6

·

No ECUs or sensors are connected to the sub bus.*7



·

Gateway function equipped ECUs relay signals between ECUs and sensors connected to different buses.

·

*1: An ECU or sensor is installed to the vehicle but is not displayed on the "Communication Bus Check" screen.

·

*2: The gateway function equipped ECU does not memorize ECUs and sensors connected to its respective sub bus.

·

*3: The gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus.

·

*4: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.

·

*5: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.

·

*6: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.

·

*7: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.

·

The example of the CAN Bus Check screen in the illustration shows the result of electrical noise on the CAN bus which is caused by an open in a CAN branch line of HV is also unstable. In addition, in this example, MB is equipped with a gateway function. Therefore, communication is also unstable between the Sub bus ECUs of MB and the bus 4.

·

The example in the illustration shows that HV has a red background color on the CAN Bus Check screen. This indicates a more significant communication stop. In this case, a communication stop of HV is suspected.



d.

If a communication error is indicated on both the bus 4 and Sub bus on the CAN Bus Check screen, suspect any communication stop displayed for the bus 4 first.

Example: Open in both CAN branch lines of MB on the bus 4

C360879C01
0.708,1.292 1.021,1.448 0.313,0.156 10 false *a 0.708,1.781 1.021,1.938 0.313,0.156 10 false *b 6.344,1.635 6.656,1.792 0.313,0.156 10 false *b
*a Background color is red *b Not displayed


HINT:
·

In the CAN bus check, it is possible to confirm the communication status of ECUs connected to the bus after connecting the GTS to the DLC3. As for sub bus, it is possible to confirm which sub bus connected ECUs can communicate with a gateway function equipped ECU on the bus.

·

If a gateway function equipped ECU has a communication error, ECUs connected to the gateway function equipped ECU are also affected, and communication stops will be indicated.

·

The CAN Bus Check screen in the illustration shows that MB has a gateway function and a communication stop in MB is suspected.




e.

If the CAN Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.

Example: Open in both CAN branch lines of MIR-R on the sub bus

C360880C01
6.354,1.615 6.667,1.771 0.313,0.156 10 false *a
*a Background color is red - -


HINT:
·

A communication error in a sub bus does not affect the other buses.

·

When a gateway function equipped ECU has memorized the ECUs that are connected to the sub bus, if any of the ECUs connected to the gateway function equipped ECU has a communication error, the background color changes to yellow or red. (The displayed name will not disappear.)




f.

If both of the bus 2 main bus lines are open, ECUs or sensors that are located farther away from the central gateway ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.

(In this case, HVB, R-MGC and ENG background color changes to red.)

C360881C01
6.344,5.896 6.656,6.094 0.313,0.198 10 false *f 0.75,5.969 1.063,6.167 0.313,0.198 10 false *f 0.417,2.667 0.875,2.865 0.458,0.198 10 false CGW 1.031,1.125 1.281,1.292 0.25,0.167 10 false *a 1.021,2.302 1.271,2.469 0.25,0.167 10 false *b 1.021,4.469 1.271,4.635 0.25,0.167 10 false *d 1.698,3.521 1.948,3.688 0.25,0.167 10 false *c 2.073,0.719 2.656,0.917 0.583,0.198 10 false F-MGC 1.927,1.292 2.76,1.49 0.833,0.198 10 false CAN J/C 1 1.854,1.885 2.188,2.083 0.333,0.198 10 false HV 2.458,1.865 2.875,2.031 0.417,0.167 10 false BRK 1.854,3.135 2.271,3.302 0.417,0.167 10 false MB 1.958,2.458 2.792,2.656 0.833,0.198 10 false CAN J/C 3 2.917,3.896 3.75,4.094 0.833,0.198 10 false CAN J/C 5 4.833,3.906 5.667,4.104 0.833,0.198 10 false CAN J/C 6 3.875,2.448 4.708,2.646 0.833,0.198 10 false CAN J/C 4 3.76,0.719 4.344,0.917 0.583,0.198 10 false HVB 4.313,0.719 4.896,0.917 0.583,0.198 10 false R-MGC 6.427,1.302 6.833,1.5 0.406,0.198 10 false ENG 3.875,1.281 4.708,1.479 0.833,0.198 10 false CAN J/C 2 3.74,3.073 4.167,3.25 0.427,0.177 10 false EPS 4.406,3.073 4.74,3.24 0.333,0.167 10 false STR 5.74,2.458 6.083,2.667 0.344,0.208 10 false SRS 6.469,3.896 6.75,4.083 0.281,0.188 10 false ST 5,4.531 5.5,4.781 0.5,0.25 10 false MIR-L 3.052,4.531 3.552,4.781 0.5,0.25 10 false MIR-R 1.521,4.573 2.021,4.823 0.5,0.25 10 false DLC3 5.479,0.635 6.094,0.833 0.615,0.198 10 false : *e
*a Bus 2 *b Bus 4
*c Sub Bus *d V Bus
*e Location of Malfunction *f Background color is red


HINT:

If a communication error occurs in an ECU, it is not displayed on the CAN Bus Check screen even though the ECU is present.



g.

If both of the sub bus main bus lines are open, ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.

(In this case, MIR-L background color changes to red.)

C360882C01
1.031,1.146 1.344,1.302 0.313,0.156 10 false *a 1.031,2.313 1.344,2.469 0.313,0.156 10 false *b 1.708,3.552 2.021,3.708 0.313,0.156 10 false *c 1.021,4.458 1.333,4.615 0.313,0.156 10 false *d 5.5,0.625 5.896,0.792 0.396,0.167 10 false : *e 0.75,6.771 1.063,6.927 0.313,0.156 10 false *f 0.438,2.698 0.896,2.896 0.458,0.198 10 false CGW 2.063,0.74 2.646,0.99 0.583,0.25 10 false F-MGC 1.948,1.281 2.948,1.448 1,0.167 10 false CAN J/C 1 3.875,1.281 4.875,1.448 1,0.167 10 false CAN J/C 2 4.802,3.896 5.802,4.063 1,0.167 10 false CAN J/C 6 2.885,3.896 3.885,4.063 1,0.167 10 false CAN J/C 5 3.75,0.729 4.333,0.979 0.583,0.25 10 false HVB 4.323,0.74 4.906,0.99 0.583,0.25 10 false R-MGC 6.406,1.292 6.823,1.542 0.417,0.25 10 false ENG 5.74,2.458 6.156,2.708 0.417,0.25 10 false SRS 1.865,1.885 2.281,2.135 0.417,0.25 10 false HV 2.469,1.885 2.885,2.135 0.417,0.25 10 false BRK 1.958,2.458 2.958,2.625 1,0.167 10 false CAN J/C 3 3.875,2.448 4.875,2.615 1,0.167 10 false CAN J/C 4 1.854,3.146 2.188,3.396 0.333,0.25 10 false MB 3.75,3.073 4.167,3.323 0.417,0.25 10 false EPS 4.396,3.073 4.813,3.323 0.417,0.25 10 false STR 1.521,4.573 1.938,4.823 0.417,0.25 10 false DLC3 3.063,4.51 3.563,4.76 0.5,0.25 10 false MIR-R 4.969,4.51 5.469,4.76 0.5,0.25 10 false MIR-L 6.469,3.917 6.802,4.167 0.333,0.25 10 false ST
*a Bus 2 *b Bus 4
*c Sub Bus *d V Bus
*e Location of Malfunction *f Background color is red



h.

When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the CAN Bus Check screen.

Details of Malfunction
Short between CAN lines (CANH and CANL)
Short between a CAN line (CANH or CANL) and +B
Short between a CAN line (CANH or CANL) and ground
Open in a CAN main bus line

C360883C01
0.604,0.198 0.917,0.354 0.313,0.156 10 false *a 0.625,1.938 0.938,2.094 0.313,0.156 10 false *b 0.719,1.031 1.031,1.188 0.313,0.156 10 false *c 0.719,1.448 1.031,1.604 0.313,0.156 10 false *d 6.354,1.281 6.667,1.438 0.313,0.156 10 false *d 6.344,0.948 6.656,1.104 0.313,0.156 10 false *c 6.354,2.99 6.667,3.146 0.313,0.156 10 false *d 0.698,3.146 1.01,3.302 0.313,0.156 10 false *d
*a When any of the following malfunctions occur on the bus 4 *b When any of the following malfunctions occur on a sub bus
*c Background color is red *d Not displayed


HINT:
·

When a malfunction occurs in the bus, almost all ECUs and sensors on the bus and sub bus indicate a communication error (almost all ECUs are not displayed). As communication with the gateway function equipped ECU that is connected to the bus stops, communication from the ECUs connected to the sub bus that is monitored by the gateway function equipped ECU also stops (these ECUs are not displayed).

·

When a malfunction occurs in a sub bus, almost all ECUs connected to the sub bus indicate a communication error.

·

A communication error in a sub bus does not affect the other buses.

·

The malfunctioning part can be determined by checking for a short circuit between CAN bus lines or between a CAN bus line and ground or +B short using an electrical tester.




i.

If a communication error of all ECUs and sensors is indicated on the CAN Bus Check screen, a communication stop of the V bus (DLC3 - central gateway ECU) is suspected.

Open in both CAN branch lines in the V bus

C360884C01
1.031,1.146 1.344,1.302 0.313,0.156 10 false *a 1.031,2.313 1.344,2.469 0.313,0.156 10 false *b 1.698,3.531 2.01,3.688 0.313,0.156 10 false *c 1.021,4.385 1.333,4.542 0.313,0.156 10 false *d 5.5,0.635 6,0.875 0.5,0.24 10 false : *e 0.719,6.219 0.969,6.385 0.25,0.167 10 false *f 6.385,6.135 6.635,6.302 0.25,0.167 10 false *f 0.448,2.667 0.948,2.833 0.5,0.167 10 false CGW 2.063,0.719 2.646,0.885 0.583,0.167 10 false F-MGC 1.948,1.302 2.865,1.469 0.917,0.167 10 false CAN J/C 1 3.844,1.292 4.76,1.458 0.917,0.167 10 false CAN J/C 2 1.927,2.469 2.844,2.635 0.917,0.167 10 false CAN J/C 3 3.833,2.479 4.75,2.646 0.917,0.167 10 false CAN J/C 4 2.917,3.906 3.833,4.073 0.917,0.167 10 false CAN J/C 5 4.813,3.906 5.729,4.073 0.917,0.167 10 false CAN J/C 6 3.75,0.719 4.167,0.885 0.417,0.167 10 false HVB 4.313,0.729 4.979,0.896 0.667,0.167 10 false R-MGC 6.417,1.313 6.917,1.563 0.5,0.25 10 false ENG 5.729,2.479 6.229,2.729 0.5,0.25 10 false SRS 6.469,3.917 6.969,4.167 0.5,0.25 10 false ST 4.99,4.51 5.49,4.76 0.5,0.25 10 false MIR-L 3.063,4.531 3.563,4.781 0.5,0.25 10 false MIR-R 1.521,4.573 2.021,4.823 0.5,0.25 10 false DLC3 1.854,3.146 2.354,3.396 0.5,0.25 10 false MB 3.75,3.094 4.083,3.344 0.333,0.25 10 false EPS 4.385,3.094 4.719,3.344 0.333,0.25 10 false STR 1.865,1.906 2.198,2.156 0.333,0.25 10 false HV 2.469,1.896 2.885,2.146 0.417,0.25 10 false BRK
*a Bus 2 *b Bus 4
*c Sub Bus *d V Bus
*e Location of Malfunction *f Not displayed


HINT:

When there is no communication between the GTS and the vehicle, no ECUs or sensors will be displayed.




DTC TABLE BY ECU


HINT:
·

In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.

·

If CAN communication system DTCs are output, the trouble cannot be determined solely from the DTCs. Perform troubleshooting according to "How to Proceed with Troubleshooting".

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If system function temporarily returns to normal, DTCs may not be output again even though the following DTC check procedures are used.



a.

BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) / GTS Display "Brake"

HINT:

DTC communication uses the CAN communication system.


Chassis > Brake > Trouble Codes
50001 435
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U007488 Control Module Communication Bus "B" Off Bus Off Either condition is met:
·

The response sent to the brake actuator assembly (skid control ECU) and steering sensor from the airbag sensor assembly is invalid for 1 second or more.

·

The following condition occurs 10 times consecutively within 60 seconds: The response sent to the brake actuator assembly (skid control ECU) from the airbag sensor assembly is invalid at least once within 5 seconds.

·

The brake actuator assembly (skid control ECU) cannot send or receive data (the bus is off) 10 times consecutively.


All conditions are met:
·

1 second or more elapses after the ignition switch is ON.

·

The brake actuator assembly (skid control ECU) power supply voltage is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least 60 seconds.
·

ABS indicator light illuminates.

·

SLIP indicator light illuminates.


The DTC remains stored until it is cleared using the GTS.
U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the brake actuator assembly (skid control ECU) and ECM continuously for 2 seconds or more. All conditions are met:
·

1 second or more elapses after the ignition switch is ON.

·

The vehicle speed is 15 km/h (9 mph) or more.

·

The brake actuator assembly (skid control ECU) power supply voltage is between 10 and 17.4 V.


Drive the vehicle for 3 seconds at a speed of 15 km/h (9 mph) or more. SLIP indicator light illuminates. The DTC remains stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Either condition is met:
·

Communication stop occurs between the brake actuator assembly (skid control ECU) and airbag sensor assembly continuously for 1 second or more.

·

The following condition occurs 10 times or more consecutively within 60 seconds: The brake actuator assembly (skid control ECU) is unable to receive certain data from the airbag sensor assembly at least once within 5 seconds.


All conditions are met:
·

1 second or more elapses after the ignition switch is ON.

·

The brake actuator assembly (skid control ECU) power supply voltage is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least 60 seconds.
·

ABS indicator light illuminates.

·

SLIP indicator light illuminates.


The DTC remains stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Either condition is met:
·

Communication stop occurs between the brake actuator assembly (skid control ECU) and steering sensor for continuously 1 second or more.

·

The following condition occurs 10 times or more consecutively within 60 seconds: The brake actuator assembly (skid control ECU) is unable to receive certain data from the steering sensor at least once within 5 seconds.


All conditions are met:
·

1 second or more elapses after the ignition switch is ON.

·

The brake actuator assembly (skid control ECU) power supply voltage is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least 60 seconds. SLIP indicator light illuminates. The DTC remains stored until it is cleared using the GTS.


b.

COMBINATION METER ASSEMBLY / GTS Display "Combination Meter"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Combination Meter > Trouble Codes
50001 122
DTC No. Detection Item DTC Detection Condition DTC Check Procedure DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM/PCM "A" The combination meter assembly is unable to receive certain data from the ECM for 2 seconds or more. Both conditions are met:
·

Turning the ignition switch to ON.

·

The voltage at the IG power supply terminal of the combination meter assembly is 11.5 V or higher.


Turn the ignition switch to ON and wait at least 2 seconds. MIL illuminates. The DTC remains stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Either condition is met:
·

The combination meter assembly is unable to receive certain data from the brake actuator assembly (skid control ECU) for 2 seconds or more.

·

The combination meter assembly is unable to receive certain data from the brake actuator assembly (skid control ECU) for 3 seconds or more.


Both conditions are met:
·

Turning the ignition switch to ON.

·

The voltage at the IG power supply terminal of the combination meter assembly is 11.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds.
·

ABS indicator light illuminates.

·

SLIP indicator light illuminates.

·

Brake warning light illuminates.


The DTC remains stored until it is cleared using the GTS.
U0151 Lost Communication with Restraints Control Module The combination meter assembly is unable to receive certain data from the airbag sensor assembly for 10 seconds or more. Both conditions are met:
·

Turning the ignition switch to ON.

·

The voltage at the IG power supply terminal of the combination meter assembly is 11.5 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. SRS warning light illuminates. The DTC remains stored until it is cleared using the GTS.
U023A Lost Communication with Front Camera Module The combination meter assembly is unable to receive certain data from the forward recognition camera for 10 seconds or more. Both conditions are met:
·

Turning the ignition switch to ON.

·

The voltage at the IG power supply terminal of the combination meter assembly is 11.5 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. The PCS warning light illuminates. The DTC remains stored until it is cleared using the GTS.


c.

FORWARD RECOGNITION CAMERA (w/ Pre-collision System) / GTS Display "Pre-Collision System"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Pre-Collision System > Trouble Codes
50001 432
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method

*: Refer to Pre-collision System

Click here(Click here)

U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the forward recognition camera and ECM continuously for approximately 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 5 km/h (3 mph) or more.


Drive the vehicle for approximately 6 seconds or more at a speed of 5 km/h (3 mph) or more. The PCS warning light illuminates. DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag sensor assembly continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 5 km/h (3 mph) or more.


Drive the vehicle for 4 seconds or more at a speed of 5 km/h (3 mph) or more. The PCS warning light illuminates. DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the forward recognition camera and spiral with sensor cable sub-assembly (steering angle sensor) continuously for approximately 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. The PCS warning light illuminates. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for approximately 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. The PCS warning light illuminates. DTC is stored until it is cleared using the GTS.
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the forward recognition camera and combination meter assembly continuously for approximately 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. The PCS warning light illuminates. DTC is stored until it is cleared using the GTS.
U023587* Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message Communication stop occurs between the forward recognition camera and millimeter wave radar sensor assembly continuously for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. The PCS warning light illuminates. DTC is stored until it is cleared using the GTS.
U023A87* Lost Communication with Image Processing Module "A" Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for approximately 2 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. The PCS warning light illuminates. DTC is stored until it is cleared using the GTS.
U030051* Internal Control Module Software Incompatibility Not Programmed The control system information sent from the ECM remains undefined by the forward recognition camera for approximately 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 6 seconds. The PCS warning light illuminates. DTC is stored until it is cleared using the GTS.


d.

FORWARD RECOGNITION CAMERA (w/ Pre-collision System) / GTS Display "Front Recognition Camera"

HINT:

DTC communication uses the CAN communication system.


Chassis > Front Recognition Camera > Trouble Codes
50001 430
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the forward recognition camera and ECM continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. - DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag sensor assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the forward recognition camera and steering sensor continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - DTC is stored until it is cleared using the GTS.
U015587 Lost Communication with Body Control Module Missing Message Communication stop occurs between the forward recognition camera and combination meter assembly continuously for 50 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - DTC is stored until it is cleared using the GTS.


e.

MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-collision System) / GTS Display "Front Radar Sensor"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Front Radar Sensor > Trouble Codes
50001 429
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method

*: Refer to Front Radar Sensor System

Click here(Click here)

U010487* Lost Communication with Driving Support ECU Missing Message Either condition is met:
·

The millimeter wave radar sensor assembly does not receive data from the forward recognition camera for approximately 1 second or more.

·

A checksum error is continuously detected for approximately 1 second or more.


All conditions are met:
·

Approximately 1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the millimeter wave radar sensor assembly is 8 V or higher.


Turn the ignition switch to ON and wait for at least approximately 2 seconds. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


f.

AIRBAG SENSOR ASSEMBLY

HINT:

The airbag sensor assembly is connected to the CAN communication system but CAN communication DTCs are not stored.



g.

SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

HINT:

The spiral with sensor cable sub-assembly (steering angle sensor) is connected to the CAN communication system but CAN communication DTCs are not stored.



h.

Central Gateway ECU (Network Gateway ECU)

HINT:

The central gateway ECU (network gateway ECU) is connected to the CAN communication system, but the central gateway ECU (network gateway ECU) does not store or output CAN communication DTCs.



i.

Regarding the past communication error of ECUs and sensors connected to the V bus (in this case, normal was displayed when performing the CAN bus check, but communication DTCs are output), the probable CAN branch that had a malfunction can be determined based on the following DTC combination table.



CAN BUS WAVEFORMS


C353604E03
1.521,0.677 1.854,0.281 1.854,0.281 1.99,0.281 false 4.427,1 4.427,0.271 4.427,0.271 4.563,0.271 true 4.438,3.948 4.438,2.521 4.438,2.521 5.219,2.521 true 6.354,3.948 6.354,2.521 6.354,2.521 5.646,2.521 true 5.375,3.688 5.375,4.781 5.375,4.781 5.51,4.781 false 2.063,0.208 3.208,0.448 1.146,0.24 10 false CAN Main Bus 4.656,0.198 7.052,0.479 2.396,0.281 10 false Open in CAN Main Bus Line (CANH) 5.313,3.167 6.385,3.365 1.073,0.198 10 false ECU 3.417,3.167 4.49,3.365 1.073,0.198 10 false ECU 1.594,3.167 2.667,3.365 1.073,0.198 10 false ECU 3.885,4.01 5.208,4.531 1.323,0.521 10 false Open in CAN Branch Line (CANL) 5.76,4 7.073,4.49 1.313,0.49 10 false Open in CAN Branch Line (CANH) 5.604,4.708 6.708,5.177 1.104,0.469 10 false CAN Branch 1.469,4.781 3.802,5.031 2.333,0.25 10 false : CAN Main Bus Line (CANH) 1.479,5.219 3.677,5.521 2.198,0.302 10 false : CAN Main Bus Line (CANL) 1.479,5.813 3.51,6.094 2.031,0.281 10 false : CAN Branch Line (CANH) 1.469,6.25 3.625,6.521 2.156,0.271 10 false : CAN Branch Line (CANL)

HINT:
·

This waveform is measured between terminals CANH and GND, and terminals CANL and GND of the DLC3. (Use this as a reference for diagnosis of CAN communication lines.)

·

When malfunctions in multiple ECUs are suspected based on the CAN bus check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first. If no problems are found, check the following waveforms.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main wire, an open in a CAN branch wire, or a short between a CAN wire (CANH or CANL) and ground is suspected (Group 2).

·

Wiggle the connector and wire harness to check if the waveform changes.



a.

CAN bus waveforms (Group 1)

i.
C265973N04
0.5,1.5 0.667,1.5 0.667,1.5 0.917,1.167 true 0.5,0.5 0.667,0.5 0.667,0.5 0.906,0.781 true 0.083,0.417 0.698,0.615 0.615,0.198 10 CANH 0.135,1.417 0.75,1.615 0.615,0.198 10 CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 50 μs/DIV. 2.708,0.25 3.427,0.448 0.719,0.198 10 1 V/DIV. 2.958,1.385 3.417,1.583 0.458,0.198 10 GND

Normal waveform


ii.
C265974N03
1.5,1.417 1.667,1.417 1.667,1.417 1.969,1.104 true 1.5,0.5 1.667,0.5 1.667,0.5 1.969,0.792 true 1.052,0.417 1.667,0.615 0.615,0.198 10 CANH 1.135,1.333 1.75,1.531 0.615,0.198 10 CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 50 μs/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 GND 2.667,0.24 3.354,0.417 0.688,0.177 10 1 V/DIV.

Open in both of the lines (CANH and CANL) of a CAN branch

HINT:
·

Waveforms (waveforms shown using dotted lines) are not output from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)

·

Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.




iii.
C265975N03
0.5,1.333 0.75,1.333 0.75,1.333 1.063,0.969 true 1.292,0.917 0.729,0.583 0.729,0.583 0.5,0.583 true 0.083,0.5 0.698,0.698 0.615,0.198 10 CANH 0.135,1.25 0.75,1.448 0.615,0.198 10 CANL 1.344,1.917 2.875,2.115 1.531,0.198 10 50 μs/DIV. 2.729,0.271 3.354,0.479 0.625,0.208 10 1 V/DIV. 2.938,1.385 3.396,1.583 0.458,0.198 10 GND

Short between the CAN bus lines (CANH and CANL)

HINT:
·

Waveforms disappear.

·

If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.





b.

CAN bus waveforms (reference) (Group 2)

NOTICE:

The following CAN bus waveforms can be used only as reference. The actual measured waveform may differ significantly depending on the location of the open or short circuit.


i.
C265976N03
0.938,0.76 0.667,0.5 0.667,0.5 0.5,0.5 true 0.5,1.5 0.667,1.5 0.667,1.5 0.844,1.167 true 0.083,0.417 0.698,0.615 0.615,0.198 10 CANH 0.135,1.417 0.75,1.615 0.615,0.198 10 CANL 1.313,1.927 2.844,2.125 1.531,0.198 10 50 μs/DIV. 2.708,0.281 3.344,0.5 0.635,0.219 10 1 V/DIV. 2.969,1.385 3.427,1.583 0.458,0.198 10 GND

Open in a CAN branch wire (CANH)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch wires. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch wire is disconnected.




ii.
C265977N03
0.5,1.417 0.667,1.417 0.667,1.417 0.906,1.146 true 0.5,0.5 0.667,0.5 0.667,0.5 0.833,0.74 true 0.083,0.417 0.698,0.615 0.615,0.198 10 CANH 0.135,1.344 0.75,1.542 0.615,0.198 10 CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 50 μs/DIV. 2.698,0.281 3.417,0.51 0.719,0.229 10 1 V/DIV. 2.958,1.385 3.417,1.583 0.458,0.198 10 GND

Open in a CAN branch wire (CANL)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch wires. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch wire is disconnected.




iii.
C265978N03
0.5,0.5 0.667,0.5 0.667,0.5 0.938,0.708 true 0.5,1.417 0.75,1.417 0.75,1.417 0.938,1.156 true 0.083,0.417 0.698,0.615 0.615,0.198 10 CANH 0.135,1.333 0.75,1.531 0.615,0.198 10 CANL 1.323,1.927 2.854,2.125 1.531,0.198 10 50 μs/DIV. 2.698,0.281 3.281,0.521 0.583,0.24 10 1 V/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 GND

Open in a CAN main wire (CANH)

HINT:
·

Waveforms of ECUs or sensors that are closer to the DLC3 than the open part are almost normal.

·

Waveforms of ECUs or sensors that are on the opposite side of the DLC3 from the open part are abnormal.

·

An open in a CAN main wire can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.




iv.
C265979N03
0.5,1.75 0.75,1.75 0.75,1.75 1.083,1.531 true 1.063,1.333 0.75,0.917 0.75,0.917 0.5,0.917 true 0.083,0.833 0.698,1.031 0.615,0.198 10 CANH 0.083,1.667 0.698,1.865 0.615,0.198 10 CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 50 μs/DIV. 2.719,0.302 3.375,0.552 0.656,0.25 10 1 V/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 GND

Short between a CAN bus line (CANH) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connector(s) from the CAN junction connector(s) or when disconnecting ECUs or sensors.

·

A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.




v.
C265980N03
0.5,1.583 0.667,1.583 0.667,1.583 0.833,1.385 true 0.5,0.5 0.667,0.5 0.667,0.5 1.021,0.708 true 0.083,0.417 0.698,0.615 0.615,0.198 10 CANH 0.135,1.5 0.75,1.698 0.615,0.198 10 CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 50 μs/DIV. 2.698,0.271 3.292,0.531 0.594,0.26 10 1 V/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 GND

Short between a CAN bus line (CANL) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connector(s) from the CAN junction connector(s) or when disconnecting ECUs or sensors.

·

A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.






DATA SENDING/RECEIVING TABLE


a.

Data sending/receiving table

HINT:

If Data List items related to sent/received data are not displayed properly, the part for which communication is interrupted can be determined using the table below.


Data content Data Detected and Sent by Data Received from
(Can be Checked in Data List)
Data Received
(Cannot be Checked in Data List)
Selected System*2 Relevant Data List Item
[Selected System]
Engine speed ECM
·

Brake actuator assembly (skid control ECU)

·

Combination meter assembly


·

Air conditioning amplifier assembly

·

4 wheel drive control ECU

·

Certification ECU (smart key ECU assembly)

·

Airbag sensor assembly

·

Headlight leveling ECU assembly

·

Radio and display receiver assembly


Engine and ECT Engine Speed
Engine and Transmission Engine Speed
ABS/VSC/TRC Engine Revolutions
Brake Engine Revolutions
Combination Meter Engine Rpm
Stop and Start Engine Spd (ECM)
PPS Engine Revolution (PPS)
Engine coolant temperature ECM
·

Air conditioning amplifier assembly

·

Combination meter assembly

·

Engine stop and start ECU


·

Brake actuator assembly (skid control ECU)

·

Certification ECU (smart key ECU assembly)


Engine and ECT Coolant Temp
Engine and Transmission Coolant Temperature
Combination Meter Engine/FC Coolant Temperature
Air Conditioner Engine Coolant Temp
Stop and Start Coolant Temperature
Stop light switch ECM - Airbag sensor assembly - -
ABS/VSC/TRC Stop Light SW
Power Source Control Stop Light Switch1
Stop and Start Stop Light SW (ABS/VSC)
Wheel speed signal Brake actuator assembly (skid control ECU) 4 wheel drive control ECU
·

ECM

·

Headlight leveling ECU assembly

·

Engine stop and start ECU

·

Forward recognition camera


Brake
·

FR Wheel Speed

·

FL Wheel Speed

·

RR Wheel Speed

·

RL Wheel Speed


ABS/VSC/TRC
·

FR Wheel Speed

·

FL Wheel Speed

·

RR Wheel Speed

·

RL Wheel Speed


Four Wheel Drive
·

FR Wheel Speed

·

FL Wheel Speed

·

RR Wheel Speed

·

RL Wheel Speed


Steering angle signal Steering sensor
·

Brake actuator assembly (skid control ECU)

·

Engine stop and start ECU

·

Power steering ECU assembly


·

Airbag sensor assembly

·

Forward recognition camera

·

ECM

·

Radio and display receiver assembly

·

Parking assist ECU


Brake Steering Angle Value
ABS/VSC/TRC Steering Angle Sensor
Stop and Start Steering Angle
PPS Steering Angle (PPS)
Vehicle speed Brake actuator assembly (skid control ECU)
·

ECM

·

Combination meter assembly

·

4 wheel drive control ECU

·

Power steering ECU assembly

·

Radio and display receiver assembly

·

Engine stop and start ECU


·

Airbag sensor assembly

·

Forward recognition camera


Brake Vehicle Speed
Engine and ECT Vehicle Speed
Engine and Transmission Vehicle Speed
Combination Meter Vehicle Speed Meter
Four Wheel Drive Vehicle Speed
Navigation System Vehicle Speed
Stop and Start Vehicle Spd1 (ABS/VSC)
PPS Vehicle Speed (PPS)
Combination meter assembly*1 -
·

Air conditioning amplifier assembly

·

Certification ECU (smart key ECU assembly)

·

Airbag sensor assembly


Combination Meter Vehicle Speed Meter

*1: The combination meter assembly receives a vehicle speed signal from the brake actuator assembly (skid control ECU) and sends the signal to other ECUs.

*2: According to the display on the GTS, read the Data List.

-

Enter the following menus: Powertrain / Engine and Transmission / Data List

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>DATA LIST / ACTIVE TEST

-

Enter the following menus: Body Electrical / Combination Meter / Data List

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST