Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2022.09
RM25T0E _58 Vehicle Interior _128087 PRE-COLLISION _0548646 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U023A87  Lost Communication with Image Processing Module "A" Missing Message  


DESCRIPTION

The forward recognition camera communicates with the skid control ECU (brake actuator assembly) via CAN communication.

If a communication error is detected between the skid control ECU (brake actuator assembly) and forward recognition camera, the forward recognition camera stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
U023A87 Lost Communication with Image Processing Module "A" Missing Message When the ignition switch is ON for 2 seconds or more, a communication malfunction between the skid control ECU (brake actuator assembly) and the forward recognition camera is detected for approximately 3 seconds or more.
·

Vehicle stability control system

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the forward recognition camera is replaced with a new one, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereVehicle Interior>PRE-COLLISION>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereVehicle Interior>PRE-COLLISION>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereVehicle Interior>PRE-COLLISION>FRONT CAMERA>DRIVING ADJUSTMENT




PROCEDURE

1.CHECK FOR DTCs (Brake)
a.

Using the GTS, check for vehicle stability control system DTCs.

Chassis > Brake > Trouble Codes
50001 435
HINT:

If DTC U023A87 and vehicle stability control system DTCs are output, perform troubleshooting for the vehicle stability control system first.



Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.PERFORM DEALER MODE (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

B

2.PERFORM DEALER MODE (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
HINT:

When entering Dealer Mode (Signal Check), the skid control ECU (brake actuator assembly) communicates with the forward recognition camera to judge whether the vehicle is equipped with the pre-collision system. Therefore, do not exit Dealer Mode (Signal Check) within 5 seconds of entering Dealer Mode (Signal Check).


a.

Procedure to Enter Dealer Mode (Signal Check)

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is centered.


iii.

Check that park (P) is selected.


iv.

Connect the GTS to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the GTS on.


vii.

Switch the skid control ECU to Dealer Mode (Signal Check) using the GTS.

Chassis > Brake > Utility
Tester Display
Signal Check
50005 435 4558
HINT:

After entering Dealer Mode (Calibration), maintain Dealer Mode (Calibration) condition for 5 seconds. If Dealer Mode (Calibration) is ended before 5 seconds elapse, enter Dealer Mode (Calibration) again, wait 5 seconds, and then check for DTCs again.




b.

Confirm the system has entered Dealer Mode (Signal Check)

i.

Confirm that the ABS warning light, brake system warning light (yellow indicator) and slip indicator light indicate the Dealer Mode pattern (blinking at 0.25 second intervals).

HINT:

When entering Dealer Mode (Signal Check), if the parking brake is engaged, the parking brake indicator light (red) will illuminate, and if the parking brake is not engaged, the parking brake indicator light (red) will blink in the Dealer Mode pattern (blinking at 0.25 second intervals).


Result:
Proceed to
NEXT




c.

End of Dealer Mode (Signal Check)

i.

Turn the ignition switch off.


ii.

Disconnect the GTS.




NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Pre-Collision System > Clear DTCs
50002 432
Result:
Proceed to
NEXT




NEXT

4.CHECK FOR DTCs
4.CHECK FOR DTCs
a.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



b.

Check for DTCs.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432
Result:
Result Proceed to
U023A87 is not output A
U023A87 is output B




A

END

B

REPLACE FORWARD RECOGNITION CAMERA