Home › Engine / Hybrid System › 1VD-FTV (EMISSION CONTROL) › EXHAUST FUEL ADDITION INJECTOR (for DPF) › from 2022.09
RM25T0E _51 Engine / Hybrid System _029525 1VD-FTV EMISSION CONTROL _0290816 EXHAUST FUEL ADDITION INJECTOR(for DPF) A

1VD-FTV EMISSION CONTROL  EXHAUST FUEL ADDITION INJECTOR(for DPF)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 23710B 3.REMOVE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

a.

Disconnect the exhaust fuel addition injector connector.


b.
A391349C01
0.792,1.656 0.896,1.344 0.896,1.344 1.01,1.344 false 0.885,2.427 0.99,2.115 0.99,2.115 1.104,2.115 false 1.073,1.26 1.438,1.479 0.365,0.219 10 false *1 1.156,2.042 1.49,2.25 0.333,0.208 10 false *2
*1 Washer
*2 Nozzle Holder Clamp


Remove the bolt, washer and nozzle holder clamp.


c.

Remove the exhaust fuel addition injector and gasket.


Hide 23901H 4.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A391350

Turn the retainer shown in the illustration.

NOTICE:
·

Check for foreign matter on the fuel tube around the fuel tube connector. Clean it if necessary. Foreign matter can affect the ability of the O-ring to seal the fuel tube connector and fuel pipe.

·

Do not use any tools to separate the fuel tube connector and fuel pipe.

·

Do not forcefully bend, kink or twist the nylon tube.

·

Keep the fuel tube connector and fuel pipe free from foreign matter.

·

Put the fuel tube connector and fuel pipe in plastic bags to prevent damage and contamination.




b.
A271333C01
0.948,0.344 1.104,0.344 1.104,0.344 1.604,0.771 false 2.615,0.615 2.458,0.615 2.458,0.615 2.281,0.854 false 2.521,1.833 2.333,1.833 2.333,1.833 2.042,1.406 false 1.698,1.208 1.698,1.708 true 2.656,0.531 3,0.74 0.344,0.208 10 false *1 0.74,0.26 1.052,0.448 0.313,0.188 10 false *a 2.583,1.75 2.958,1.969 0.375,0.219 10 false *b 1.625,1.76 1.938,1.948 0.313,0.188 10 false *c
*1 Exhaust Fuel Addition Injector
*a Fuel Tube Connector
*b Retainer
*c O-Ring


Disconnect the fuel tube connector from the exhaust fuel addition injector.


Hide 23255B 5.REMOVE FUEL INJECTOR SEAL

a.
A201784C03
1.969,0.854 2.115,0.552 2.115,0.552 2.292,0.552 false 2.385,0.479 2.698,0.635 0.313,0.156 10 false *1
*1 Fuel Injector Seal


Remove the fuel injector seal from the exhaust fuel addition injector assembly.