Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2022.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) U

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  TERMINALS OF ECM  


for RHD
A163584E04
2.396,0.188 2.906,0.5 0.51,0.313 2.396,0.188 2.906,0.5 0.51,0.313 5.531,0.188 6.042,0.5 0.51,0.313 2.521,0.26 2.823,0.438 0.302,0.177 10 false C39 5.667,0.271 5.938,0.479 0.271,0.208 10 false A29

for LHD
A163584E07
2.396,0.188 2.906,0.5 0.51,0.313 2.396,0.188 2.906,0.5 0.51,0.313 5.531,0.188 6.042,0.5 0.51,0.313 2.521,0.26 2.823,0.438 0.302,0.177 10 false C39 5.667,0.271 5.938,0.479 0.271,0.208 10 false I84

Measure the voltage according to the value(s) in the table below.

HINT:

The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated.

The result of the checks should be compared with the standard normal voltage for that pair of terminals, which is displayed in the Specified Condition column.

The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A29-20 (BATT) - C39-81 (E1)*1
I84-20 (BATT) - C39-81 (E1)*2
R-B - BR Battery (for measuring the battery voltage and for the ECM memory) Always 11 to 14 V
A29-28 (IGSW) - C39-81 (E1)*1
I81-28 (IGSW) - C39-81 (E1)*2
B - BR Ignition switch Ignition switch ON 11 to 14 V
A29-2 (+B) - C39-81 (E1)*1
I84-2 (+B) - C39-81 (E1)*2
L - BR Power source of ECM Ignition switch ON 11 to 14 V
A29-1 (+B2) - C39-81 (E1)*1
I84-1 (+B2) - C39-81 (E1)*2
B - BR*1
L - BR*2
Power source of ECM Ignition switch ON 11 to 14 V
A29-44 (MREL) - C39-81 (E1)*1
I84-44 (MREL) - C39-81 (E1)*2
W-G - BR*1
G - BR*2
MAIN relay (MAIN) Ignition switch ON 11 to 14 V
10 seconds elapsed after ignition switch turned off 0 to 1.5 V
C39-66 (VCPM) - C39-112 (EPIM) L-R - BR Power source of manifold absolute pressure sensor (for PIM) Ignition switch ON 4.5 to 5.5 V
C39-118 (VCM) - C39-92 (E2) L-R - BR Power source of fuel pressure sensor (for PCR1) Ignition switch ON 4.5 to 5.5 V
C39-120 (VCEG) - C39-97 (EEGL) P - V Power source of EGR valve position sensor Ignition switch ON 4.5 to 5.5 V
C39-110 (VCVL) - C39-87 (EVLU) L-R - W-R Power source of throttle position sensor Ignition switch ON 4.5 to 5.5 V
C39-71 (VG) - C39-94 (EVG) L-Y - G-W Mass air flow meter Engine is warmed up: Idling, A/C switch OFF 0.5 to 3.4 V
C39-115 (THA) - C39-92 (E2) Y-B - BR Intake air temperature sensor (built into mass air flow meter) Engine is warmed up: Idling, intake air temperature at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C39-108 (VN) - C39-81 (E1) L - BR VRV (Vacuum Regulating Valve) Idling Pulse generation
A29-53 (VPA) - A29-57 (EPA)*1
I84-53 (VPA) - I84-57 (EPA)*2
L-R - L*1
R - W*2
Accelerator pedal position sensor (for engine control) Ignition switch ON, accelerator pedal fully released 0.6 to 1.0 V
Ignition switch ON, accelerator pedal fully depressed 3.0 to 4.6 V
A29-54 (VPA2) - A29-58 (EPA2)*1
I84-54 (VPA2) - I84-58 (EPA2)*2
R-B - BR*1
B - BR*2
Accelerator pedal position sensor (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 1.4 to 1.8 V
Ignition switch ON, accelerator pedal fully depressed 3.7 to 5.0 V
A29-55 (VCPA) - A29-57 (EPA)*1
I84-55 (VCPA) - I84-57 (EPA)*2
L-W - L*1
L - W*2
Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
A29-56 (VCP2) - A29-58 (EPA2)*1
I84-56 (VCP2) - I84-58 (EPA2)*2
BR-W - BR*1
P - BR*2
Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
C39-90 (THIA) - C39-92 (E2) W-G - BR Intake air temperature sensor (after turbocharged) Engine is warmed up: Idling, intake air temperature sensor (after turbocharged) at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C39-93 (THW) - C39-92 (E2) G-B - BR Engine coolant temperature sensor Engine is warmed up: Idling, engine coolant temperature at 60 to 120°C (140 to 248°F) 0.2 to 1.2 V
C39-40 (#1) - C39-81 (E1) Y-G - BR Fuel injector Idling Pulse generation
(see waveform 1)
C39-39 (#2) - C39-81 (E1) B - BR
C39-38 (#3) - C39-81 (E1) L - BR
C39-37 (#4) - C39-81 (E1) R-W - BR
C39-36 (#5) - C39-81 (E1) G - BR
C39-35 (#6) - C39-81 (E1) V - BR
C39-34 (#7) - C39-81 (E1) W-L - BR
C39-33 (#8) - C39-81 (E1) P - BR
C39-80 (G+) - C39-79 (G-) W - B Camshaft position sensor Idling Pulse generation
C39-78 (NE+) - C39-77 (NE-) B - W Crankshaft position sensor Idling Pulse generation
C39-67 (PIM) - C39-112 (EPIM) P-L - BR Manifold absolute pressure sensor Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied 0.1 to 0.7 V
Same as atmospheric pressure 0.8 to 1.4 V
Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied 1.6 to 2.2 V
A29-45 (IREL) - C39-81 (E1)*1
I84-45 (IREL) - C39-81 (E1)*2
P - BR EDU 1 relay Ignition switch ON 0 to 1.5 V
A29-46 (IRL2) - C39-81 (E1)*1
I84-46 (IRL2) - C39-81 (E1)*2
R - BR EDU 2 relay Ignition switch ON 0 to 1.5 V
C39-72 (PCR1) - C39-95 (E2M) B - BR Fuel pressure sensor Idling (Approximately 35 MPa (357 kgf/cm2, 5078 psi)) 1.3 to 1.8 V
A29-12 (GREL) - C39-81 (E1)*1
I84-12 (GREL) - C39-81 (E1)*2
R - BR No. 1 glow relay Cranking 11 to 14 V
Idling 0 to 1.5 V
A29-23 (GRL2) - C39-81 (E1)*1
I84-23 (GRL2) - C39-81 (E1)*2
L - BR No. 2 glow relay Cranking 11 to 14 V
Idling 0 to 1.5 V
C39-116 (THF) - C39-92 (E2) G-R - BR Fuel temperature sensor Ignition switch ON 0.5 to 3.4 V
C39-104 (PCV+) - C39-105 (PCV-) W - BR Suction control valve Idling Pulse generation
(see waveform 2)
C39-61 (INJ1) - C39-81 (E1) G-R - BR No. 1 injector driver Idling Pulse generation
(see waveform 3)
C39-60 (INJ2) - C39-81 (E1) W - BR No. 2 injector driver Idling Pulse generation
(see waveform 3)
C39-64 (VLU) - C39-92 (E2) L-W - BR Throttle position sensor (for Bank 1) Ignition switch ON
(throttle valve fully opened)
2.8 to 3.8 V
Idling
(throttle valve fully closed)
0.4 to 1.0 V
C39-65 (IG) - C39-92 (E2) L-W - BR Throttle position sensor (for Bank 2) Ignition switch ON
(throttle valve fully opened)
2.8 to 3.8 V
Idling
(throttle valve fully closed)
0.4 to 1.0 V
C39-57 (LUSL) - C39-81 (E1) B - BR Diesel throttle duty signal (for Bank 1) Engine warmed up, racing engine Pulse generation
(see waveform 4)
C39-56 (ILL+) - C39-81 (E1) B - BR Diesel throttle duty signal (for Bank 2) Engine warmed up, racing engine Pulse generation
(see waveform 4)
A29-59 (EGRA) - C39-92 (E2)*1
I84-59 (EGRA) - C39-92 (E2)*2
L - BR EGR valve position sensor Ignition switch ON 0.6 to 1.4 V
C39-86 (EGM+) - C39-81 (E1) B - BR EGR valve duty signal Engine warmed up, idling Pulse generation
C39-85 (EGM-) - C39-81 (E1) W - BR EGR valve duty signal Engine warmed up, idling Pulse generation
C39-43 (ECBV) - C39-81 (E1) R - BR Vacuum switching valve assembly (for EGR Bypass Valve) Vacuum switching valve assembly (for EGR Bypass Valve) on 0 to 1.5 V
Vacuum switching valve assembly (for EGR Bypass Valve) off 11 to 14 V
A29-13 (STP) - C39-81 (E1)*1
I84-13 (STP) - C39-81 (E1)*2
W - BR Stop light switch Ignition switch ON, brake pedal depressed 7.5 to 14 V
Ignition switch ON, brake pedal released 0 to 1.5 V
A29-35 (ST1-) - C39-81 (E1)*1
I84-35 (ST1-) - C39-81 (E1)*2
R-L - BR*1
L - BR*2
Stop light switch
(opposite to STP)
Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A29-15 (TACH) - C39-81 (E1)*1
I84-15 (TACH) - C39-81 (E1)*2
B - BR Engine speed Idling Pulse generation
(see waveform 5)
A29-8 (SPD) - C39-81 (E1)*1
I84-8 (SPD) - C39-81 (E1)*2
G - BR Speed signal from combination meter Ignition switch ON, wheel rotated slowly Pulse generation
(see waveform 6)
A29-48 (STA) - C39-81 (E1)*1
I84-48 (STA) - C39-81 (E1)*2
B-W - BR*1
LG - BR*2
Starter signal Cranking 6.0 V or more
C39-53 (ALT) - C39-81 (E1) R - BR Generator duty ratio Idling Pulse generation
A29-27 (TC) - C39-81 (E1)*1
I84-27 (TC) - C39-81 (E1)*2
G - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
A29-30 (AC1) - C39-81 (E1)*1
I84-30 (AC1) - C39-81 (E1)*2
B-W - BR*1
V - BR*2
A/C signal A/C switch ON 0 to 1.5 V
A/C switch OFF 11 to 14 V
A29-18 (ACT) - C39-81 (E1)*1
I84-18 (ACT) - C39-81 (E1)*2
L-B - BR*1
GR - BR*2
A/C signal Ignition switch ON 11 to 14 V
A/C cut control ON 0 to 3 V
A29-14 (IUSW) - C39-81 (E1)*1
I84-14 (IUSW) - C39-81 (E1)*2
L-R - BR*1
R - BR*2
Idle up switch Idle up switch ON 0 to 3 V
Idle up switch OFF 11 to 14 V
C39-51 (RSW) - C39-81 (E1) R-B - BR Back up light switch Ignition switch ON, shift position is reverse 11 to 14 V
Ignition switch ON, shift position is not reverse 0 to 3 V
C39-28 (CLSW) - C39-81 (E1) P-B - BR*1
B - BR*2
Clutch switch Ignition switch ON, clutch pedal fully depressed 0 to 3 V
Ignition switch ON, clutch pedal fully released 11 to 14 V
A29-38 (FSW) - C39-81 (E1)*1
I84-38 (FSW) - C39-81 (E1)*2
L-W - BR*1
L - BR*2
Shift position switch Ignition switch ON, shift position is first 0 to 3 V
Ignition switch ON, shift position is not first 11 to 14 V
A29-41 (CANH) - C39-81 (E1)*1
I84-41 (CANH) - C39-81 (E1)*2
B - BR CAN communication line Ignition switch ON Pulse generation
(see waveform 7)
A29-49 (CANL) - C39-81 (E1)*1
I84-49 (CANL) - C39-81 (E1)*2
W - BR CAN communication line Ignition switch ON Pulse generation
(see waveform 8)
C39-54 (PRD) - C39-81 (E1) Y - BR Pressure discharge valve drive signal Engine warmed up, engine racing Pulse generation
(see waveform 9)
C39-32 (RLFF) - C39-81 (E1) R - BR Pressure discharge valve confirmation signal Engine warmed up, engine racing Pulse generation
(see waveform 9)
C39-122 (THCF) - C39-99 (ETCF) L - BR Exhaust gas temperature sensor Engine warmed up, idling 4.6 to 4.9 V
C39-121 (THCI) - C39-99 (ETCF) G-Y - BR No. 2 exhaust gas temperature sensor Engine warmed up, idling 4.6 to 4.9 V
C39-123 (THCO) - C39-99 (ETCF) W - BR No. 3 exhaust gas temperature sensor Engine warmed up, idling 4.6 to 4.9 V
C39-83 (FIV) - C39-81 (E1) W - BR Exhaust fuel addition injector assembly Exhaust fuel addition injector assembly operating Pulse generation
C39-45 (HA1A) - C39-23 (E05) L - BR Air fuel ratio sensor heater Ignition switch ON Pulse generation
C39-102 (A1A+) - C39-23 (E05) R - BR Air fuel ratio sensor Ignition switch ON 2.0 to 2.5 V
C39-103 (A1A-) - C39-23 (E05) G - BR Air fuel ratio sensor Ignition switch ON 2.0 to 2.5 V
C39-69 (PEX) - C39-92 (E2) L-W - BR*1
R - BR*2
Differential pressure sensor Ignition switch ON 0.4 to 4.8 V
C39-91 (VC) - C39-92 (E2) B - BR Power source for differential pressure sensor Ignition switch ON 4.5 to 5.5 V
A29-16 (DPSW) - C39-81 (E1)*1
I84-16 (DPSW) - C39-81 (E1)*2
L - BR DPF switch DPF switch ON 0 to 1.5 V
DPF switch OFF 8.5 to 14 V
A29-32 (EC) - Body ground*1
I84-32 (EC) - Body ground*2
BR - Body ground*1
W-B - Body ground*2
Ground circuit of ECM Always Below 1 Ω
C39-81 (E1) - Body ground BR - Body ground Ground circuit of ECM Always Below 1 Ω
C39-92 (E2) - Body ground BR - Body ground Ground circuit of ECM Always Below 1 Ω
C39-22 (E01) - Body ground BR - Body ground*1
W-B - Body ground*2
Ground circuit of ECM Always Below 1 Ω
C39-21 (E02) - Body ground W-B - Body ground Ground circuit of ECM Always Below 1 Ω
C39-23 (E05) - Body ground BR - Body ground*1
W-B - Body ground*2
Ground circuit of ECM Always Below 1 Ω

HINT:
·

*1: for RHD

·

*2: for LHD



WAVEFORM 1


A009438E23
0.396,0.427 0.604,0.625 0.208,0.198 10 false #1 0.396,0.781 0.635,0.99 0.24,0.208 10 false #2 0.417,1.135 0.646,1.344 0.229,0.208 10 false #7 0.406,1.5 0.625,1.708 0.219,0.208 10 false #3 2.729,0.938 3.281,1.135 0.552,0.198 10 false 5 V/DIV. 1.167,2 2.083,2.177 0.917,0.177 10 false 20 msec./DIV.

Fuel Injector No. 1 (to No. 8) Injection Signal
ECM Terminal Name Between #1 to #8 and E1
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the injector injection.



WAVEFORM 2


A097624E20
0.229,1.229 0.698,1.427 0.469,0.198 10 false PCV+ 2.781,1.021 3.427,1.25 0.646,0.229 10 false 10 V/DIV. 1.375,1.958 2.229,2.125 0.854,0.167 10 false 5 msec./DIV.

Suction Control Valve Signal
ECM Terminal Name Between PCV+ and PCV-
Tester Range 10 V/DIV., 5 msec./DIV.
Condition Idling or cranking with warm engine

HINT:

The waveform varies depending on the suction control valve operation.



WAVEFORM 3


A009437E21
0.375,0.865 0.781,1.063 0.406,0.198 10 false INJ1 2.74,0.917 3.375,1.125 0.635,0.208 10 false 2 V/DIV. 1.354,1.948 2.302,2.167 0.948,0.219 10 false 20 msec./DIV.

Injector Injection Confirmation Signal
ECM Terminal Name Between INJ1 and E1
Between INJ2 and E1
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the injector injection.



WAVEFORM 4


A091225E14
0.292,1.083 0.771,1.281 0.479,0.198 10 false LUSL 2.708,1.083 3.313,1.281 0.604,0.198 10 false 1 V/DIV. 1.417,1.948 2.375,2.156 0.958,0.208 10 false 2 msec./DIV.

Diesel Throttle Motor Signal
ECM Terminal Name Between LUSL and E1
Between LUS2 and E1
Tester Range 1 V/DIV., 2 msec./DIV.
Condition Racing with warm engine

HINT:

The waveform varies depending on the throttle valve operation.



WAVEFORM 5


A292385E05
0.542,1.167 1,1.365 0.458,0.198 10 false GND 0.125,0.125 0.948,0.354 0.823,0.229 10 false 5 V/DIV. 1.75,1.917 2.854,2.104 1.104,0.188 10 false 10 msec./DIV.

Engine Speed Signal
ECM Terminal Name Between TACH and E1
Tester Range 5 V/DIV., 10 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 6


G037487E27
0.073,1.146 0.469,1.344 0.396,0.198 10 false SPD 2.75,0.115 3.406,0.313 0.656,0.198 10 false 5 V/DIV. 2.885,1.177 3.292,1.375 0.406,0.198 10 false GND 1.229,1.979 2.385,2.177 1.156,0.198 10 false 10 msec./DIV.

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 5 V/DIV., 10 msec./DIV.
Condition Driving at vehicle speed of 40 km/h (25 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 7


A303295E01
2.771,0.167 3.385,0.375 0.615,0.208 10 false 1 V/DIV. 2.958,1.25 3.344,1.5 0.385,0.25 10 false GND 1.573,1.781 2.625,2.031 1.052,0.25 10 false 10 msec./DIV.

CAN Communication Signal
ECM Terminal Name Between CANH and E1
Tester Range 1 V/DIV., 10 msec./DIV.
Condition Engine stopped, ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 8


A303296E01
2.802,0.156 3.396,0.385 0.594,0.229 10 false 1 V/DIV. 2.99,1.229 3.333,1.469 0.344,0.24 10 false GND 1.615,1.76 2.719,1.969 1.104,0.208 10 false 10 msec./DIV.

CAN Communication Signal
ECM Terminal Name Between CANL and E1
Tester Range 1 V/DIV., 10 msec./DIV.
Condition Engine stopped, ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 9


A243948E11
0.156,0.813 0.75,1.052 0.594,0.24 10 false (b) RLFF 0.24,2.115 0.76,2.354 0.521,0.24 10 false (a) PRD 1.5,2.698 2.354,2.938 0.854,0.24 10 false 1 msec./DIV. 2.719,0.24 3.271,0.479 0.552,0.24 10 false 2 V/DIV.

Pressure Discharge Valve Drive Signal and Pressure Discharge Confirmation Signal
ECM Terminal Name (a) Between PRD and E1
(b) Between RLFF and E1
Tester Range 2 V/DIV., 1 msec./DIV.
Condition Engine warmed up, engine racing