Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › from 2022.09
RM25T0E _58 Vehicle Interior _029925 THEFT DETERRENT / KEYLESS ENTRY _0138323 IMMOBILISER SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  TERMINALS OF ECU  


CHECK TRANSPONDER KEY ECU ASSEMBLY


B354639E11
3.333,0.583 3.833,0.833 0.5,0.25 3.458,0.625 3.917,0.823 0.458,0.198 10 false L30

a.

Disconnect the L30 transponder key ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
L30-5 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
L30-1 (+B) - L30-5 (GND) Input P - W-B Battery Always 11 to 14 V +B
L30-2 (IG) - L30-5 (GND) Input GR - W-B Ignition switch Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V
L30-3 (KSW) - L30-5 (GND) Input R - W-B Unlock warning switch signal No key in ignition key cylinder 10 kΩ or higher Key SW/B2780
Key in ignition key cylinder Below 1 Ω


c.

Reconnect the L30 transponder key ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
L30-8 (IND) - L30-5 (GND) Output L - W-B Security indicator light signal No key in ignition key cylinder, or 20 seconds elapsed after turning ignition switch to ACC or off (immobiliser system set) Pulse generation Immobiliser
Key in ignition key cylinder (immobiliser system unset) Below 1 V
L30-9 (D) - L30-5 (GND) Input/Output W - W-B DLC3 communication Without communication Below 1 V -
During communication Pulse generation
L30-4 (ANT1) - L30-5 (GND) Input/Output P - W-B Transponder key amplifier power source No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 1)
L30-15 (ANT2) - L30-5 (GND) Input/Output W - W-B Transponder key amplifier communication signal No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 2)
L30-12 (EFII) - L30-5 (GND) Input G - W-B ECM input signal Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 3)
E/G Start Permission
L30-13 (EFIO) - L30-5 (GND) Output Y - W-B ECM output signal Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 4)


e.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B329909N02
5.76,0.854 6.219,1.052 0.458,0.198 10 GND

Tester Connection L30-4 (ANT1) - L30-5 (GND)
Tool Setting 20 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


ii.

Waveform 2 (Reference)

B329910N02
5.75,0.854 6.208,1.052 0.458,0.198 10 GND

Tester Connection L30-15 (ANT2) - L30-5 (GND)
Tool Setting 20 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


iii.

Waveform 3 (Reference)

B253467C11
1.563,1.198 2.01,1.406 0.448,0.208 10 GND 2.188,1.302 2.438,1.49 0.25,0.188 10 *a 2.802,1.313 3.031,1.49 0.229,0.177 10 *b
*a Approximately 160 ms *b Approximately 510 ms


Tester Connection L30-12 (EFII) - L30-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


iv.

Waveform 4 (Reference)

B253466C11
3.521,1.365 3.708,1.542 0.188,0.177 10 *a 4.094,1.354 4.281,1.531 0.188,0.177 10 *b 1.552,1.208 1.885,1.385 0.333,0.177 10 GND
*a Approximately 160 ms *b Approximately 510 ms


Tester Connection L30-13 (EFIO) - L30-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 1GR-FE)


B489449C02
2.354,0.25 2.76,0.479 0.406,0.229 5.688,0.302 6.01,0.521 0.323,0.219 5.083,0.302 5.427,0.51 0.344,0.208 2.448,0.292 2.906,0.49 0.458,0.198 10 false C39 5.76,0.323 6.219,0.521 0.458,0.198 10 false I84 5.135,0.323 5.594,0.521 0.458,0.198 10 false A29 5.458,0.333 5.771,0.531 0.313,0.198 10 false *A 6.073,0.333 6.385,0.531 0.313,0.198 10 false *B
*A for RHD *B for LHD


HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


a.

Measure the, voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
A29-10 (IMO) - C39-81 (E1) *1
I84-10 (IMO) - C39-81 (E1) *2
Output G - BR Transponder key ECU assembly output signal Ignition switch off 11 to 14 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
E/G Start Permission
A29-11 (IMI) - C39-81 (E1) *1
I84-11 (IMI) - C39-81 (E1) *2
Input G-Y - BR*1
Y - BR*2
Transponder key ECU assembly input signal Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
E/G Start Permission

*1: for RHD

*2: for LHD



b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B253467C12
1.563,1.198 2.01,1.406 0.448,0.208 10 GND 2.188,1.302 2.438,1.49 0.25,0.188 10 *a 2.802,1.313 3.031,1.49 0.229,0.177 10 *b
*a Approximately 160 ms *b Approximately 510 ms


Tester Connection A29-10 (IMO) - C39-81 (E1) *1
I84-10 (IMO) - C39-81 (E1) *2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

*1: for RHD

*2: for LHD



ii.

Waveform 2 (Reference)

B253466C12
3.521,1.365 3.708,1.542 0.188,0.177 10 *a 4.094,1.354 4.281,1.531 0.188,0.177 10 *b 1.552,1.208 1.885,1.385 0.333,0.177 10 GND
*a Approximately 160 ms *b Approximately 510 ms


Tester Connection A29-11 (IMI) - C39-81 (E1) *1
I84-11 (IMI) - C39-81 (E1) *2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

*1: for RHD

*2: for LHD





CHECK ECM (for 1VD-FTV)


B489449C03
2.354,0.25 2.76,0.479 0.406,0.229 5.688,0.302 6.01,0.521 0.323,0.219 5.083,0.302 5.427,0.51 0.344,0.208 2.448,0.292 2.906,0.49 0.458,0.198 10 false C39 5.76,0.323 6.219,0.521 0.458,0.198 10 false I84 5.135,0.323 5.594,0.521 0.458,0.198 10 false A29 5.458,0.333 5.771,0.531 0.313,0.198 10 false *A 6.073,0.333 6.385,0.531 0.313,0.198 10 false *B
*A for RHD *B for LHD


HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


a.

Measure the, voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A29-10 (IMO) - C39-81 (E1)*1
I84-10 (IMO) - C39-81 (E1)*2
Output G - BR Transponder key ECU assembly output signal Ignition switch off 11 to 14 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
E/G Start Permission
A29-11 (IMI) - C39-81 (E1)*1
I84-11 (IMI) - C39-81 (E1)*2
Input G-Y - BR Transponder key ECU assembly input signal Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
E/G Start Permission

*1: for RHD

*2: for LHD



b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B253467C13
1.563,1.198 2.01,1.406 0.448,0.208 10 GND 2.188,1.302 2.438,1.49 0.25,0.188 10 *a 2.802,1.313 3.031,1.49 0.229,0.177 10 *b
*a Approximately 160 ms *b Approximately 510 ms


Measurement Condition
Item Content
Tester Connection A29-10 (IMO) - C39-81 (E1)*1
I84-10 (IMO) - C39-81 (E1)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

*1: for RHD

*2: for LHD



ii.

Waveform 2 (Reference)

B253466C13
3.521,1.365 3.708,1.542 0.188,0.177 10 *a 4.094,1.354 4.281,1.531 0.188,0.177 10 *b 1.552,1.208 1.885,1.385 0.333,0.177 10 GND
*a Approximately 160 ms *b Approximately 510 ms


Measurement Condition
Item Content
Tester Connection A29-11 (IMI) - C39-81 (E1)*1
I84-11 (IMI) - C39-81 (E1)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

*1: for RHD

*2: for LHD