There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
| Symptom | Trouble Area |
|---|---|
| The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω. |
·
Short between CAN bus lines and GND
·
ECM
·
Brake actuator assembly (skid control ECU)
·
Spiral with sensor cable sub-assembly (steering angle sensor)
·
Airbag sensor assembly
·
Combination meter assembly
·
No. 4 CAN junction connector
·
No. 5 CAN junction connector
·
DLC3 CAN branch wire or connector |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
When disconnecting and reconnecting the battery.
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the infofmation stored in it will not match the infofmation from the vehicle and a DTC may be stored.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to No. 5 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to ECM | *d | to Brake Actuator Assembly (Skid Control ECU) |
| *e | to No. 4 CAN Junction Connector | - | - |
Disconnect the No. 5 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| I111-3 (CANH) - I17-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ECM |
| I111-9 (CANL) - I17-4 (CG) | |||
| I111-4 (CANH) - I17-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Brake actuator assembly (skid control ECU) |
| I111-10 (CANL) - I17-4 (CG) | |||
| I111-6 (CANH) - I17-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 4 CAN junction connector |
| I111-12 (CANL) - I17-4 (CG) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to No. 4 CAN junction connector CAN main wire) | B |
| NG (ECU or sensor CAN wires) | C |
A
B
C
Reconnect the I111 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 4 CAN junction connectors.
| *1 | No. 4 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector (to No. 4 CAN Junction Connector) |
*b | Front view of DLC3 |
| No. 4 CAN Junction Connector | Wiring Color | Connect to |
|---|---|---|
| I112-1 (CANH) | G | Combination meter assembly |
| I112-2 (CANL) | W | |
| I113-1 (CANH) | L | DLC3 |
| I113-2 (CANL) | W | |
| I114-1 (CANH) | P | Spiral with sensor cable sub-assembly (steering angle sensor) |
| I114-2 (CANL) | W | |
| I115-1 (CANH) | B | No. 5 CAN junction connector |
| I115-2 (CANL) | W | |
| I116-1 (CANH) | P | Airbag sensor assembly |
| I116-2 (CANL) | W |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| I112-1 (CANH) - I17-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Combination meter assembly |
| I112-2 (CANL) - I17-4 (CG) | |||
| I113-1 (CANH) - I17-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | DLC3 |
| I113-2 (CANL) - I17-4 (CG) | |||
| I114-1 (CANH) - I17-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Spiral with sensor cable sub-assembly (steering angle sensor) |
| I114-2 (CANL) - I17-4 (CG) | |||
| I115-1 (CANH) - I17-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 5 CAN junction connector |
| I115-2 (CANL) - I17-4 (CG) | |||
| I116-1 (CANH) - I17-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Airbag sensor assembly |
| I116-2 (CANL) - I17-4 (CG) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to DLC3 CAN branch wire) | B |
| NG (to No. 5 CAN junction connector CAN main wire) | C |
| NG (ECU or sensor CAN wires) | D |
A
B
C
D
| *a | Front view of DLC3 |
Reconnect the CAN junction connector.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I17-6 (CANH) - I17-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I17-14 (CANL) - I17-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG