СИСТЕМА ЗАРЯДКИ АККУМУЛЯТОРНОЙ БАТАРЕИ > ПРОВЕРКА БЕЗ СНЯТИЯ С АВТОМОБИЛЯ

для подготовки Нажмите здесь



1. CHECK BATTERY CONDITION

ПРИМЕЧАНИЕ:
If the battery is weak or if the engine is difficult to start, perform the following procedures.

  1. Check the battery for damage and deformation. If severe damage, deformation or leakage is found, replace the battery.

  1. Check the electrolyte quantity of each cell.

    УКАЗАНИЕ:
    Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.).


    1. For maintenance-free batteries:

      1. If the electrolyte quantity is below the lower line, replace the battery.
      2. If the electrolyte quantity is above the lower line, check the battery voltage when cranking the engine. If the voltage is below 9.6 V, recharge or replace the battery.

    2. For non-maintenance-free batteries:

      1. If the electrolyte quantity is below the lower line, add distilled water to each cell. Then, recharge the battery and check the electrolyte's specific gravity.

        Standard specific gravity:
        1.25 to 1.29 at 20°C (68°F)

      2. If the electrolyte quantity is above the lower line, check the battery voltage when cranking the engine. If the voltage is below 9.6 V, recharge or replace the battery.

  1. Turn the ignition switch off and turn on the headlights for 20 to 30 seconds. This removes the surface charge from the battery.

  1. Measure the battery voltage between the negative (-) and positive (+) terminals of the battery.

    Standard voltage:
    12.5 to 12.9 V at 20°C (68°F)

    If the voltage is less than the specification, recharge the battery.



2. INSPECT BATTERY TERMINAL AND FUSE

  1. Check that the battery terminals are not loose or corroded.
    If the terminals are corroded, clean the terminals.

  1. Measure the resistance of the H-fuses and fuses.

    Standard Resistance:
    Below 1 Ω

    If the result is not as specified, replace the fuses.



3. INSPECT FAN AND GENERATOR V BELT


    A0098UAE13

  1. Убедитесь в отсутствии износа, трещин и других признаков повреждения.
    При обнаружении следующих дефектов замените вентилятор и поликлиновой ремень генератора.

    1. Ремень имеет трещины.
    2. Ремень изношен до такой степени, что обнажились волокна
    3. Отсутствуют элементы ребер ремня.



    A009A9ZE11

  1. Убедитесь в том, что приводной ремень правильно располагается в углублениях шкива.
    Обозначения на рисунке 
    *a
    		ПРАВИЛЬНО
    *b
    		НЕПРАВИЛЬНО

    УКАЗАНИЕ:
    Рукой проверьте, не выскользнул ли ремень из канавок в нижней части шкива. Если ремень выскользнул из канавки шкива, замените поликлиновой ремень. Правильно установите новый поликлиновой ремень.



    A009BK1E03

  1. Убедитесь, что индикаторная метка натяжителя находится в диапазоне A, как показано на рисунке.
    Обозначения на рисунке 
    *1
    		Метка со стороны кронштейна
    *2
    		Метка со стороны рычага
    *3
    		Поликлиновой ремень вентилятора и генератора
    *4
    		Натяжитель
    Если метка находится вне зоны A, замените поликлиновой ремень вентилятора и генератора.



4. INSPECT GENERATOR WIRING

  1. Visually check the generator wiring.

    1. Check that the wiring is in good condition.



5. CHECK FOR ABNORMAL NOISES

  1. Listen for abnormal noises from the generator.

    1. Check that no abnormal noises are heard from the generator while the engine is running.



6. INSPECT CHARGE WARNING LIGHT CIRCUIT

  1. Turn the ignition switch to ON. Check that the charge warning light comes on.

  1. Start the engine and check that the light goes off.
    If the light does not operate as specified, troubleshoot the charge warning light circuit.



7. INSPECT CHARGING CIRCUIT WITHOUT LOAD


  1. Connect a voltmeter and ammeter to the charging circuit as follows.



      A0094Z5E04

    1. Disconnect the wire from terminal B of the generator, and then connect it to the negative (-) lead of an ammeter.
      Text in Illustration 
      *1
      		Battery
      *2
      		Terminal B
      *3
      		Generator

    2. Connect the positive (+) lead of the ammeter to terminal B of the generator.

    3. Connect the positive (+) lead of a voltmeter to the positive (+) terminal of the battery.

    4. Ground the negative (-) lead of the voltmeter.

  1. Check the charging circuit.

    1. Maintain the engine speed at 2000 rpm and check the reading on the ammeter and voltmeter.

      Standard current:
      10 A or less

      Standard voltage:
      13.2 to 14.8 V

      If the voltmeter reading is higher than the standard voltage, replace the generator assembly.

      УКАЗАНИЕ:
      If the battery is not fully charged, the ammeter reading will sometimes be higher than the standard current.



8. INSPECT CHARGING CIRCUIT WITH LOAD

  1. With the engine running at 2000 rpm, turn the high beam headlights on and turn the heater blower switch to the HI position.

  1. Check the reading on the ammeter.

    Standard current:
    30 A or higher

    If the ammeter reading is below the standard current, repair the generator.

    УКАЗАНИЕ:
    If the battery is fully charged, the indication will sometimes be less than the standard current. If this is the case, add more electrical load (operate the wipers, rear window defogger, etc.) and check the reading on the ammeter again.