РЕЛЕ > ПРОВЕРКА БЕЗ СНЯТИЯ С АВТОМОБИЛЯ

для подготовки Нажмите здесь



1. INSPECT STARTER RELAY (ST)


    A0097X9E37

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    3 - 5
    		Battery voltage not applied to terminals 1 and 2
    		10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    		Below 1 Ω

    If the result is not as specified, replace the relay.



2. INSPECT GLOW PLUG RELAY (GLOW)


    A0097X9E37

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    3 - 5
    		Battery voltage not applied to terminals 1 and 2
    		10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    		Below 1 Ω

    If the result is not as specified, replace the relay.



3. INSPECT FUEL PUMP RELAY (FUEL PMP)


    A00993VE26

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    3 - 5
    		Battery voltage not applied to terminals 1 and 2
    		10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    		Below 1 Ω

    If the result is not as specified, replace the relay.



4. INSPECT NO. 1 INTEGRATION RELAY (IG2)

  1. Check the IG2 fuse.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      		Condition
      		Specified Condition
      IG2 fuse
      		Always
      		Below 1 Ω

      If the result is not as specified, replace the IG2 fuse.



  1. Check the IG2 relay.



      A00971WE01

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      		Condition
      		Specified Condition
      1C-1 - 1H-4
      		Battery voltage not applied to terminals 1H-1 and 1H-3
      		10 kΩ or higher
      Battery voltage applied to terminals 1H-1 and 1H-3
      		Below 1 Ω

      Text in Illustration 
      *a
      		Component without harness connected
      (Integration Relay)
      If the result is not as specified, replace the integration relay.



5. INSPECT NO. 1 INTEGRATION RELAY (EFI)

  1. Check the EFI fuse.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      		Condition
      		Specified Condition
      EFI fuse
      		Always
      		Below 1 Ω

      If the result is not as specified, replace the EFI fuse.



  1. Check the EFI relay.



      A00971WE01

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      		Condition
      		Specified Condition
      1C-1 - 1I-4
      		Battery voltage not applied to terminals 1I-2 and 1I-3
      		10 kΩ or higher
      Battery voltage applied to terminals 1I-2 and 1I-3
      		Below 1 Ω

      Text in Illustration 
      *a
      		Component without harness connected
      (Integration Relay)
      If the result is not as specified, replace the integration relay.



6. INSPECT MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)

ПРИМЕЧАНИЕ:
The ACC relay and IG1 No. 1 relay are built into the main body ECU (driver side junction block).



  1. Inspect the ACC relay.



    1. Measure the resistance according to the value(s) in the table below.


      A0099DOE01


      Text in Illustration 
      *a
      		Component without harness connected
      (Main Body ECU)
      		-
      		-

      Standard Resistance:
      Tester Connection
      		Condition
      		Specified Condition
      2D-17 - 2K-1
      		Battery voltage not applied to terminals 2A-48 and 2D-4
      		10 kΩ or higher
      Battery voltage applied to terminals 2A-48 and 2D-4
      		Below 1 Ω

      If the result is not as specified, replace the main body ECU.



  1. Inspect the IG1 No. 1 relay.



    1. Measure the resistance according to the value(s) in the table below.


      A0099DOE01


      Text in Illustration 
      *a
      		Component without harness connected
      (Main Body ECU)
      		-
      		-

      Standard Resistance:
      Tester Connection
      		Condition
      		Specified Condition
      2A-31 - 2K-1
      		Battery voltage not applied to terminals 2A-52 and 2D-4
      		10 kΩ or higher
      Battery voltage applied to terminals 2A-52 and 2D-4
      		Below 1 Ω

      If the result is not as specified, replace the main body ECU.