Home › Vehicle Exterior › BODY PANEL › FRONT FENDER APRON
BM37H0E _01 Vehicle Exterior _096506 BODY PANEL _0453123 FRONT FENDER APRON F

BODY PANEL  FRONT FENDER APRON  ASSEMBLY REPLACEMENT  


K160997

With the radiator side support assembly and cowl top side upper panel assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location

a.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K160463C01
0,0 0,0 false
K108837

Adhesive - -



b.

Remove the A.

K160464N01
5.635,3.458 6.5,2.5 6.5,2.5 6.667,2.5 false 6.75,2.417 6.906,2.615 0.156,0.198 10 false A

K160465


c.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K160466C01
0,0 0,0 false
K108837

Adhesive - -



d.

Remove the A.

K160467N01
2.073,3.563 2.833,4.5 2.833,4.5 3,4.5 false 3.083,4.417 3.24,4.615 0.156,0.198 10 false A


e.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K160468C01
0,0 0,0 false
K108837

Adhesive - -



f.

Remove the front fender apron sub-assembly.

K160469C01
2.667,4.25 2.5,4.25 2.5,4.25 2.25,3.583 false 2.75,4.177 3.063,4.333 0.313,0.156 10 false *1
*1 FRONT FENDER APRON SUB-ASSEMBLY - -


K160470



INSTALLATION


Symbol Meaning
K108823

Plug weld
K108824

Plug weld
K108825

Plug weld
K108827

Cut and Join Location
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Make sure to attach correctly in accordance with the body dimension diagram as this part affects the front wheel alignment.


d.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K160468C01
0,0 0,0 false
K108837

Adhesive - -



e.

Weld the front fender apron sub-assembly to the vehicle side.

K160471C01
2.667,4.25 2.5,4.25 2.5,4.25 2.25,3.583 false 2.75,4.177 3.063,4.333 0.313,0.156 10 false *1
*1 FRONT FENDER APRON SUB-ASSEMBLY - -


K160472C01
3.833,0.333 5.083,0.583 1.25,0.25 4.417,0.917 4.417,0.583 false 4.438,1.708 4.667,1.333 4.667,1.333 4.833,1.333 false 5.208,2.5 5.417,2.75 5.417,2.75 5.583,2.75 false 3.917,0.365 5.604,0.563 1.688,0.198 10 false 8.0 (82, 71 in.*lbf) 4.875,1.25 5.188,1.448 0.313,0.198 10 false *1 5.667,2.667 5.979,2.865 0.313,0.198 10 false *2
*1 NO.1 OUTRIGGER *2 NO.2 OUTRIGGER SUB-ASSEMBLY
V100146

N*m (kgf*cm, ft.*lbf) : Specified torque - -


K160473C01
0,0 0,0 false
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficientweld strength. (When repairing this model)

When welding 2 panels together including 780 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-6/ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




f.

Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K160474C01
0,0 0,0 false
K108837

Adhesive - -



g.

Remove A from the new parts.

HINT:

A is reused.


K160475C01
2.25,1.333 2.417,1.333 2.417,1.333 2.75,1.667 false 4.25,2.667 4.667,2.25 4.667,2.25 4.833,2.25 false 2.083,1.25 2.396,1.448 0.313,0.198 10 false *1 4.927,2.167 5.083,2.365 0.156,0.198 10 false A
*1 FRONT SIDE MEMBER REINFORCEMENT SUB-ASSEMBLY REAR - -



h.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K160466C01
0,0 0,0 false
K108837

Adhesive - -



i.

Weld the A to the vehicle side.

K160476C01
2.917,4.5 2.75,4.5 2.75,4.5 2,3.583 false 3.01,4.406 3.167,4.604 0.156,0.198 10 false A
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficientweld strength. (When repairing this model)

When welding 2 panels together including 980 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-6/ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




j.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K160463C01
0,0 0,0 false
K108837

Adhesive - -



k.

Weld the A to the vehicle side.

K160477N01
5.667,3.5 6.5,2.5 6.5,2.5 6.667,2.5 false 6.75,2.417 6.906,2.615 0.156,0.198 10 false A

K160478


l.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting /coating)


m.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.