With the front body pillar cut and join replacement sections (pattern 1) and quarter panel cut and join replacement sections (small areas) removed.
REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Remove Weld Points |
|
Cut with Disc Sander etc. |
|
Cut and Join Location |
Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)
Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.
In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.
|
Adhesive | - | - |
Remove the center body pillar outer.
| *1 | CENTER BODY PILLAR OUTER | - | - |
| *a | 50 mm (1.97 in.) | - | - |
Remove the A.
Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.
In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.
|
Adhesive | - | - |
Remove the center body pillar reinforcement sub-assembly and rocker panel sub-assembly outer.
| *1 | CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY | *2 | ROCKER PANEL SUB-ASSEMBLY OUTER |
| *a | 80 mm (3.15 in.) | - | - |
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Plug Weld |
|
Plug Weld |
|
Cut and Join Location |
|
Fillet Weld |
|
Butt Weld |
Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.
Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)
If the entire supply part is not needed, remove the part of the supply part that is needed.
| *1 | CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY | - | - |
| *a | 80 mm (3.15 in.) | - | - |
Remove A from the new parts.
| *1 | ROCKER PANEL SUB-ASSEMBLY OUTER | - | - |
Before temporarily installing the new parts, weld the center body pillar reinforcement sub-assembly and rocker panel sub-assembly outer with the standard number of welding points.
| *1 | CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY | *2 | ROCKER PANEL SUB-ASSEMBLY OUTER |
| *a | Ultra High Strength Steel Welding Point | - | - |
When welding 2 panels together including 1180 MPa ultra high strength steel.
| *a: Plug weld | Plug diameter | 10 mm (0.39 in.) |
| Wire type | AWS A5.18 ER70S-6/ER70S-3 | |
| Shield gas | Metal active gas |
Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).
Do not apply adhesive around the plug welding points.
Minimize squeeze out in plug welding areas.
|
Adhesive | - | - |
Weld the center body pillar reinforcement sub-assembly and rocker panel sub-assembly outer to the vehicle side.
| *1 | CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY | *2 | ROCKER PANEL SUB-ASSEMBLY OUTER |
| *a | Ultra High Strength Steel Welding Point | - | - |
When welding 2 panels together including 1180 MPa ultra high strength steel.
| *a: Plug weld | Plug diameter | 10 mm (0.39 in.) |
| Wire type | AWS A5.18 ER70S-6/ER70S-3 | |
| Shield gas | Metal active gas |
Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.
| *a | Ultra High Strength Steel Welding Point | *b | 15 mm (0.59 in.) |
When welding 2 panels together including 1180 MPa ultra high strength steel.
| *a: Plug weld | Plug diameter | 10 mm (0.39 in.) |
| Wire type | AWS A5.18 ER70S-6/ER70S-3 | |
| Shield gas | Metal active gas |
Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.
Weld the A to the vehicle side.
| *a | Ultra High Strength Steel Welding Point | - | - |
When welding 3 panels or more together including 1180 MPa or ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)
| *a: Plug weld | Plug diameter | Same as the standard method (See the introduction) |
| Wire type | AWS A5.18 ER70S-6/ER70S-3 | |
| Shield gas | Metal active gas |
Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).
Do not apply adhesive around the plug welding points.
Minimize squeeze out in plug welding areas.
|
Adhesive | - | - |
Weld the center body pillar outer to the vehicle side.
| *1 | CENTER BODY PILLAR OUTER | - | - |
| *a | Ultra High Strength Steel Welding Point | - | - |
When welding 3 panels or more together including 1180 MPa or ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)
| *a: Plug weld | Plug diameter | Same as the standard method (See the introduction) |
| Wire type | AWS A5.18 ER70S-6/ER70S-3 | |
| Shield gas | Metal active gas |
Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.
After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)
After welding, apply body sealer to the corresponding parts. (See the painting /coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.