Home › Vehicle Exterior › BODY PANEL › QUARTER WHEEL HOUSING OUTER PANEL
BM37H0E _01 Vehicle Exterior _096506 BODY PANEL _0453132 QUARTER WHEEL HOUSING OUTER PANEL F

BODY PANEL  QUARTER WHEEL HOUSING OUTER PANEL  ASSEMBLY REPLACEMENT  


K161010

With the quarter panel assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location

a.

A is reused.


b.

After removing the A, remove the quarter wheel house panel outer.

K160708N01
2.583,2.75 2.75,3.167 2.75,3.167 2.917,3.167 false 3.01,3.083 3.167,3.281 0.156,0.198 10 false A


c.

Remove the rocker panel reinforcement no.5.

HINT:

rocker panel reinforcement no.5 is reused.


K160709C01
1.583,3.083 1.75,3.083 1.75,3.083 2.417,2.667 false 1.417,3 1.729,3.198 0.313,0.198 10 false *1
*1 ROCKER PANEL REINFORCEMENT NO.5 - -



d.

Remove the roof side panel inner front and roof side panel outer.

K160710C01
1.417,2.521 1.083,3.667 1.083,3.667 0.917,3.667 false 2.5,1.26 2.833,0.583 2.833,0.583 3,0.583 false 0.729,3.583 1.042,3.781 0.313,0.198 10 false *1 0.667,1.719 0.979,1.917 0.313,0.198 10 false *a 3.052,0.479 3.365,0.677 0.313,0.198 10 false *2
*1 ROOF SIDE PANEL INNER FRONT *2 ROOF SIDE PANEL OUTER
*a 165 mm (6.50 in.) - -



e.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K160711C01
0,0 0,0 false
K108837

Adhesive - -



f.

Remove the quarter wheel house panel outer.

K160712C01
4.781,3.083 5.167,3.583 5.167,3.583 5.333,3.583 false 3.271,2.875 3.583,3.073 0.313,0.198 10 false *a 5.417,3.5 5.729,3.698 0.313,0.198 10 false *1
*1 QUARTER WHEEL HOUSE PANEL OUTER - -
*a 30 mm (1.18 in.) - -




INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108831

Butt Weld
K108835

Assembly Mark

a.

For positioning of the new parts, align the installation standard holes of the outer panel and the inner panel.

K160713


b.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K160711C01
0,0 0,0 false
K108837

Adhesive - -



c.

Weld the quarter wheel house panel outer to the vehicle side.

K160714C01
4.781,3.083 5.167,3.583 5.167,3.583 5.333,3.583 false 5.417,3.5 5.729,3.698 0.313,0.198 10 false *1
*1 QUARTER WHEEL HOUSE PANEL OUTER - -



d.

Weld the roof side panel inner front and roof side panel outer to the vehicle side.

K160715C01
1.417,2.521 1.083,3.667 1.083,3.667 0.917,3.667 false 2.5,1.26 2.833,0.583 2.833,0.583 3,0.583 false 0.729,3.583 1.042,3.781 0.313,0.198 10 false *1 3.052,0.479 3.365,0.677 0.313,0.198 10 false *2
*1 ROOF SIDE PANEL INNER FRONT *2 ROOF SIDE PANEL OUTER


K160716C01
1.583,3.083 1.75,3.083 1.75,3.083 2.417,2.667 false 1.417,3 1.729,3.198 0.313,0.198 10 false *1
*1 ROCKER PANEL REINFORCEMENT NO.5 - -


K160717


e.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting /coating)


f.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.