Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
NM37H0E _59 Vehicle Exterior _097226 WIPER / WASHER _0455393 WIPER AND WASHER SYSTEM GE GENERAL F

WIPER / WASHER  WIPER AND WASHER SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

Front Wiper System

i.

A wiper system with a rain sensing function (with the direct spray function) is used. This system automatically operates the wipers when rain is detected. Additionally, a washer-linked drip-prevention function is provided. When the washer is operated, the wipers also operate. The wiper system is controlled by the windshield wiper ECU integrated into the windshield wiper motor assembly and the rain sensor mounted on the upper area of the windshield.


ii.

A direct spray arm, in which the washer nozzle is built into the wiper arm, is used to spray washer fluid in the same direction as the movement of the blade.


iii.

A graphite coating is applied to the surface of the wiper rubber, reducing inversion noise and wiper flutter while the wipers are operating.



b.

Camera Cleaner System (Models with Camera Cleaner System)

i.

A camera cleaner system is used.


ii.

The camera cleaner system uses a nozzle installed on top of the television & rear inner view mirror camera assembly to spray washer fluid onto the surface of the camera lens, cleaning off foreign matter that is attached to it (such as water, mud, snow and snow-melting agents) and improving the visibility of the camera image.




PRECAUTION


a.

Camera Cleaner System

i.

Knowledge

1.

If there is a sufficient amount of washer fluid but it does not spray out, check the nozzle for blockages.

2.

The camera cleaner system cleans off foreign matter that is attached to the surface of the camera lens. Therefore, it cannot clean off ice, snow, or other foreign matter that is displayed in the camera image if the foreign matter is attached to surfaces near the camera.

3.

Do not subject the camera to sudden temperature changes such as by pouring hot water into the camera under cold weather.

4.

The washer tank is shared with the windshield washer, so if the camera cleaner system is frequently used, the washer fluid will need to be replaced more often.

5.

The cleaning operation time by the driver takes a maximum of approximately 1.5 seconds.



ii.

Cautions

1.

Rear Television Camera

(a)

During camera cleaner system operation, the sprayed washer fluid may make it difficult to see the camera image. Directly check the surrounding conditions in order to ensure safe driving.

(b)

If washer fluid remains on the surface of the camera lens after the camera cleaner system operates, the image may become difficult to see at night depending on the headlight height and angle of vehicles to the rear.


2.

Inner Mirror Camera

(a)

During the camera cleaner system operation, the sprayed washer fluid may make it difficult to see the camera image. Drive carefully while confirming the safety of your surroundings.

(b)

If washer fluid remains on the camera lens after the camera cleaner system operates, the image may become difficult to see at night depending on the headlight height and angle of vehicles to the rear. In this case, change to optical mirror mode.


3.

Do not apply excessive force to the nozzle or subject it to a strong impact. If excessive force is applied to the nozzle or it is subjected to a strong impact, it may become misaligned.

4.

In order to prevent the auxiliary battery being depleted, do not operate the camera cleaner system for a long period of time when the fuel cell system is stopped.



iii.

Handling Guide

1.

Depending on the type of foreign matter attached to the surface of the camera lens, the camera cleaner system may not completely clean the camera lens. If this occurs, wash the camera lens with a large amount of water and wipe the lens with a wet soft cloth.

2.

Do not scrub the camera lens. Scrubbing may scratch the camera lens and affect the image.



iv.

Notice

1.

If washer fluid does not spray out, do not continue to operate the rear camera washer switch. Doing so may damage the pump.

2.

In order to prevent the washer fluid from freezing, use a washer fluid that is appropriate for the outside air temperature.

3.

Do not allow water to directly contact the nozzle when washing the vehicle with a high pressure washer. The camera may stop operating normally if subject to impact from high pressure water. Also, water may enter the nozzle injection opening and freeze, causing the washer fluid to not spray properly.

4.

Contact your Toyota dealer when the nozzle is clogged. Do not unclog the nozzle such as by using a pin. Doing so may damage the nozzle.