FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
| Parking Brake Actuator Assembly | Motor | Winds and unwinds the parking brake cable based on the signals from the No. 2 skid control ECU. |
| Tension Sensor | Detects the parking brake cable tension. | |
| Electric Parking Brake Switch Assembly | ·
Locks the parking brake when the switch is pulled, and releases the parking brake when the switch is pushed. ·
Switches the auto function on and off. |
|
| Combination Meter Assembly | Parking Brake Indicator Light | ·
Lights up to inform the driver that the parking brake has locked. ·
Blinks to inform the driver that the electric parking brake system cannot be operated by driver switch operations or that a locked cable may have become loose due to external factors. |
| Brake System Warning Light (Yellow Indicator) | Lights up to inform the driver that the No. 2 skid control ECU detected a malfunction in the system. | |
| Multi-information Display | ·
Informs the driver that the No. 2 skid control ECU has a malfunction in the system. ·
Displays the switching between the manual function and auto function. |
|
| Buzzer | Sounds together with the indication of the multi-information display in order to inform the driver of a malfunction in the electric parking brake system. | |
| Airbag ECU (Airbag ECU Assembly) | Deceleration Sensor | Detects the gradient of the road surface by detecting the inclination of the vehicle. |
| Brake Actuator Assembly | No. 2 Skid Control ECU | Controls the motor in the parking brake actuator assembly based on operation signals from the electric parking brake switch assembly and parking brake request signals from ECUs. |
| EV Control ECU | Sends the accelerator pedal position signal and shift position signal to the No. 2 skid control ECU. | |
| Brake Booster with Master Cylinder Assembly | No. 1 Skid Control ECU | Sends the regulator pressure signal and brake pedal depressed signal to the No. 2 skid control ECU. |
| Main Body ECU (Multiplex Network Body ECU) | Sends the driver side door opening or closing state signal and driver seat belt fasten condition signal to the No. 2 skid control ECU. | |
| Central Gateway ECU (Network Gateway ECU) | Relays and transmits each CAN communication data signal. | |
SYSTEM CONTROL
The No. 2 skid control ECU locks or releases the parking brake by controlling the rotation direction and drive current of the motor built into the parking brake actuator assembly based on signals from the electric parking brake switch and each ECU.
The No. 2 skid control ECU detects the motor operation condition via its built-in current sensor and signals from the tension sensor built-into the parking brake actuator assembly.
The No. 2 skid control ECU generates braking force according to the road surface while the vehicle is stopped by calculating the road grade based on the signal from the deceleration sensor to control the motor drive current.
FUNCTION
Manual Function
When the electric parking brake switch assembly is pulled with the vehicle stopped, the parking brake locks.
When the brake pedal is depressed, and then the electric parking brake switch assembly is pushed, the parking brake releases.
Braking force is only generated while the electric parking brake switch is pulled up when the vehicle is in motion. The braking force is generated by hydraulic pressure, and while the braking force is being generated, the brake light illuminates. When the switch is released, the braking force decreases.
The parking brake lock operation can be operated regardless of whether the ignition switch is turned on (IG) or off.
The parking brake can be released when the ignition switch is turned on (IG).
Auto Function
The manual function can be switched to the auto function via operation of the electric parking brake switch.
When the electric parking brake switch is pulled and held for 3 seconds or more with the parking brake locked, the auto function turns on. Then a piece of information is displayed on the multi-information display indicating that the auto function is on.
When switching from the parking brake released condition, it is necessary to pull it for 5 seconds or more.
When the electric parking brake switch is pushed and held for 3 seconds or more with the parking brake released, the auto function turns off. Then a piece of information is displayed on the multi-information display indicating that the auto function is off.
When switching from the parking brake locked condition, it is necessary to press it for 5 seconds or more.
When the driver changes the shift position to P while the auto function is on, the parking brake is locked. Also, when the shift position is changed from P to any other position with the brake pedal depressed, the parking brake is released.
Parking Brake Automatic Release Function
When all of the following conditions are met and the driver depresses the accelerator pedal, the parking brake is released.
·
Driver side door is closed. ·
Shift position is not in P or N. ·
Driver side seat belt is fastened. |
FAIL-SAFE
When a malfunction occurs in the system, control using the manual function is maintained as much as possible and control using the auto function and parking brake automatic release function is prohibited.
When a malfunction occurs in the electric parking brake switch assembly, the system automatically switches to the auto function to ensure operability.
When the parking brake cannot be released due to the fail-safe state or a malfunction in the power source system, the parking brake can be released by supplying power to the electric release connector. For details, refer to the Repair Manual.
When the parking brake cannot be released due to a mechanical malfunction, the parking brake can be released by using the emergency release cable. For details, refer to the Repair Manual.
DIAGNOSIS
If a malfunction is detected in the system, the No. 2 skid control ECU will alert the driver by illuminating the brake system warning light (yellow indicator) in the combination meter and outputting a warning message on the multi-information display.
At the same time, Diagnosis Trouble Codes (DTCs) are stored in the memory. The DTCs stored in the No. 2 skid control ECU are output to the Global TechStream (GTS) connected to the DLC3. For details, refer to the Repair Manual.