Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
NM37H0E _59 Vehicle Exterior _097228 LIGHTING (EXT) _0455766 LIGHTING SYSTEM CO CONTROL F

LIGHTING (EXT)  LIGHTING SYSTEM  CONTROL  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
Headlight ECU Sub-assembly RH Controls the headlight leveling motor according to control signals from the headlight ECU sub-assembly LH.
Headlight ECU Sub-assembly LH
·

Receives various signals and controls the headlight leveling motor.

·

Sends headlight leveling motor operation signals to the headlight ECU sub-assembly RH.


Headlight Assembly LH Headlight Leveling Motor Moves the low beam headlights vertically and controls the beam axis direction according to control signals from the headlight ECU sub-assembly LH and RH.
Headlight Assembly RH Headlight Leveling Motor
Rear Height Control Sensor Sub-assembly LH Detects vehicle height value and transmits a headlight ECU sub-assembly LH.
Turn Signal Switch Light Control Switch Sends the light control switch position signal to the steering sensor.
Steering Sensor Sends the light control switch position signal to the main body ECU.
Main Body ECU (Multiplex Network Body ECU) Receives a light control signal and transmits it to the headlight ECU sub-assembly LH.
Brake Actuator Assembly No. 2 Skid Control ECU Sends the vehicle speed signal to the combination meter assembly.
Combination Meter Assembly Sends the vehicle speed signal to the main body ECU.
Central Gateway ECU (Network Gateway ECU) Relays the signal between the CAN communication lines.


SYSTEM CONTROL


a.

Dynamic Control Type

i.

The headlight control ECU sub-assembly LH receive changes in the height of the vehicle which is detected by the rear height control sensor sub-assembly LH and calculate the change in pitch of the vehicle.


ii.

The headlight ECU sub-assemblies adjust the vertical aim of the headlights based on the calculated angle of the vehicle in order to maintain a constant beam angle.

Y194545E01
1,1.625 1.177,1.208 1.177,1.208 1.417,1.208 false 1.094,2.167 1.208,2.5 1.208,2.5 1.375,2.5 false 4.646,1.698 4.823,1.281 4.823,1.281 5.063,1.281 false 4.531,1.99 4.677,2.521 4.677,2.521 4.865,2.521 false 0.042,0.594 0.979,0.896 0.938,0.302 10 false Vehicle Speed 3.354,0.635 4.302,0.927 0.948,0.292 10 false Vehicle Speed 0.063,1.833 0.813,2.469 0.75,0.635 10 false Base Beam Angle 3.583,1.823 4.323,2.375 0.74,0.552 10 false Base Beam Angle 3.302,2.885 3.74,3.167 0.438,0.281 10 false Time 6.698,2.844 7.135,3.125 0.438,0.281 10 false Time 4.469,3.135 7.021,3.771 2.552,0.635 10 false Models with Automatic Headlight Leveling Control (Dynamic Control Type) 1.052,3.073 3.302,3.594 2.25,0.521 10 false Models without Automatic Headlight Leveling Control 1.458,1.135 3.177,1.5 1.719,0.365 10 false Change in vehicle speed 1.417,2.427 3.458,2.719 2.042,0.292 10 false Deviation from Base Beam Angle 5.125,1.208 6.844,1.573 1.719,0.365 10 false Change in vehicle speed 4.906,2.448 6.948,2.74 2.042,0.292 10 false Deviation from Base Beam Angle



b.

Static Control Type

i.

The headlight ECU sub-assembly receives vehicle height change signals sent from the rear height control sensor sub-assembly and calculates the changes in the pitch angle of the vehicle. The headlight ECU sub-assembly drives the headlight leveling motor LH and RH in accordance with the change.

Control Mode Details
While Stopped If the vehicle attitude is stable for approximately 3 seconds with the headlights on while stopped, the headlight ECU sub-assembly operates the headlight leveling motor LH and RH in accordance with the detected change in vehicle attitude.




FUNCTION


a.

The height control sensor sub-assembly LH detects changes in the vehicle's rear ride height due to cargo loads etc., and operates the headlight leveling motor RH/LH in accordance with the changes, keeping the headlight axes at a constant angle.


b.

Combination Meter Assembly

i.

When a malfunction occurs in the automatic headlight beam level control system, the buzzer sounds, and the "Headlight System Malfunction Visit Your Dealer" warning message is displayed on the multi-information display.




FAIL-SAFE


a.

If the headlight ECU sub-assembly detects a malfunction in the automatic headlight beam level control system, the headlight ECU sub-assembly performs the fail-safe operation. For details, refer to the Repair Manual.