FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
| Headlight ECU Sub-assembly RH | Receives headlight control signal and shuts down power to the headlights and clearance lights. | |
| Headlight ECU Sub assembly LH | ||
| No. 2 Semiconductor Power Integration ECU | Shuts down power to the taillights, license plate lights and rear fog lights. | |
| Main Body ECU (Multiplex Network Body ECU) | Receives various signals and sends headlights, clearance lights, taillights and rear fog lights illumination signals. | |
| Steering Sensor | Sends the light control switch position signal to the main body ECU. | |
| Turn Signal Switch | Light Control Switch | Sends the light control switch position signal to the steering sensor. |
| Automatic Light Control Sensor | Detects the ambient light level and transmits them to the main body ECU. | |
| Combination Meter Assembly | ·
Displays a warning message on the multi-information display when a reminder service request signal is received. ·
Sends reminder service response signals to the main body ECU. ·
Sends the vehicle speed signal to the main body ECU. |
|
| Steering Pad Switch Assembly | Sends steering pad switch operation signals to the combination meter assembly. | |
| Brake Actuator Assembly | No. 2 Skid Control ECU | Sends the vehicle speed signal to the combination meter assembly. |
| Certification ECU (Smart Key ECU Assembly) | Sends ignition switch condition signals to the main body ECU. | |
| Central Gateway ECU (Network Gateway ECU) | Relays the signal between the CAN communication lines. | |
SYSTEM CONTROL
Headlight On Reminder Control
Headlight on reminder control interrupts the multi-information display by displaying the "Turn On Headlamps" message for approximately 6 seconds if the following conditions are met for approximately 10 seconds when the vehicle is driven at night.
The ignition switch is on (IG).
The light control switch is in the TAIL position.
The vehicle speed is more than approximately 5 km/h (3 mph).
The automatic light control sensor outputs the night mode signal.
After the message is displayed, the message is cleared if any of the following conditions are met before approximately 6 seconds have elapsed.
The ignition switch is off.
The light control switch is in the HEAD or AUTO position.
The automatic light control sensor outputs the daytime mode signal.
"BACK" is selected with the steering pad switch assembly.
Headlight Off Reminder Control (Light Control Switch in HEAD Position)
Headlight off reminder control displays the "Headlamps Are On" message on the multi-information display when 5 minutes or more elapse after the following conditions are met.
The ignition switch is off.
The low beam headlights are on (light control switch is in the HEAD position).
The driver door remains closed (is not opened) after the ignition switch is turned off.
After the message is displayed, the message is cleared if any of the following conditions are met before 6 seconds have elapsed.
The ignition switch is on (IG).
The low beam headlights are off (light control switch not in the HEAD position).
"BACK" is selected with the steering pad switch assembly.
The headlights are turned off by the light auto-turn off system.
Headlight Off Reminder Control (Light Control Switch in AUTO Position)
Headlight off reminder control interrupts the multi-information display by displaying the "Headlamps Are On Turn Headlamps Off?" message for 6 seconds if the following conditions are continuously met for 5 minutes or more.
The ignition switch is off.
The low beam headlights are on (light control switch is in the AUTO position).
The driver door remains closed (is not opened) after the ignition switch is turned off.
"Yes" or "No" is displayed on the multi-information display after the message is displayed. If "Yes" is selected with steering pad switch operation, the headlights are turned off. If "No" is selected, the headlights remain on and the displayed message is cleared.
After the message is displayed, the message is cleared if any of the following conditions are met before 6 seconds have elapsed.
The ignition switch is on (IG).
The low beam headlights are off (light control switch in the TAIL position).
The automatic light control sensor outputs the daytime mode signal.
"No" or "BACK" is selected with the steering pad switch.
The headlights are turned off by the light auto-turn off system.
FUNCTION
A reminder service function is provided to remind the user to turn the headlights on when driving at night and to turn the headlights off after turning the ignition switch off by displaying a warning message on the multi-information display.
The suggestion service function can be turned on and off using the customization function. For details, refer to the Repair Manual.