Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › PEDESTRIAN PROTECTION SYSTEM
NM37H0E _58 Vehicle Interior _097454 SUPPLEMENTAL RESTRAINT SYSTEMS _0456776 PEDESTRIAN PROTECTION SYSTEM CO CONTROL F

SUPPLEMENTAL RESTRAINT SYSTEMS  PEDESTRIAN PROTECTION SYSTEM  CONTROL  POP UP HOOD CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
Pop Up Hood Lifter Assembly LH Instantaneously pushes up the pistons using the gas generated by the inflators according to ignition signals from the airbag ECU assembly to raise the hood.
Pop Up Hood Lifter Assembly RH
Pedestrian Detection Chamber Assembly
·

Pedestrian Detection Chamber

·

Pedestrian Protection Sensor LH

·

Pedestrian Protection Sensor RH


Detects chamber (tube) deformation and sends signals used for ignition judgment to the airbag ECU assembly when a collision occurs between the vehicle (front bumper) and a pedestrian.
Steering Sensor Sends steering angle signals to the pedestrian detection ECU assembly via CAN communication.
Airbag ECU Assembly
·

Performs ignition judgment based on signals from the pedestrian protection sensors and sends ignition signals to each pop up hood lifter when a pedestrian collides with the vehicle.

·

Performs a system failure diagnosis by connecting and operating the Global TechStream (GTS) when a malfunction occurs.


EV Control ECU Sends shift position signals and the operation status of the EV control system to the airbag ECU assembly via CAN communication.
Skid Control ECU Assembly Sends vehicle speed signals, brake pedal operation signals and the operation status of the brake control system to the airbag ECU assembly via CAN communication.
Millimeter Wave Radar Sensor Assembly Radiates millimeter radar waves forward, uses the reflected waves to detect the presence of a vehicle ahead, the vehicle-to-vehicle distance and the relative speed and direction of the vehicle ahead, and then transmits this information to the forward recognition camera.
Forward Recognition Camera
·

Obtains detection information for vehicles, pedestrians and bicycles at the front of the vehicle, and sends vehicle front detection information signals to the airbag ECU assembly.

·

Sends information signals about the area at the front of the vehicle to the airbag ECU assembly when the system determines that there is a high possibility of a frontal collision.


Combination Meter Assembly
·

During a pop up hood system malfunction, warns the driver by displaying a message in the multi-information display according to the nature of the problem in the system, illuminating the pop up hood warning indicator and sounding the buzzer.

·

Sends the illumination status of warning indicators to the airbag ECU assembly via CAN communication.


DLC3 The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions.


FUNCTION


a.

Pedestrian Collision

i.

The pop up hood system operates when the vehicle (front bumper) collides with a pedestrian and a pressure change is detected in the airbag chamber.


ii.

The pop up hood system is designed to pop up in a collision with a pedestrian when driving at approximately 25 to 55 km/h (16 to 34 mph).

NOTICE:

The pop up hood system operates when the front bumper collides with a pedestrian or any obstacle.



iii.

For a pedestrian collision, if a pedestrian protection sensor detects an impact, it informs the airbag ECU assembly and causes the pop up hood lifter assemblies to be deployed.



b.

Non-operation Case

i.

When a pedestrian collides with the vehicle but the sensor ignition judgment standard is not met depending on the vehicle speed and collision situation, the pop up hood system may not operate.



c.

Prevention-linked Function Operation with Forward Pre-Collision System (PCS)

i.

When the airbag ECU assembly determines that there is a very high possibility of a collision with a pedestrian or bicycle according to information from the millimeter wave radar sensor assembly and the forward recognition camera, the airbag ECU assembly receives information to prepare to operate the pop up hood system.




SYSTEM CONTROL


a.

Pedestrian Collision

i.

The pop up hood lifters are deployed based on signals from the pedestrian protection sensors and skid control ECU assembly.

Y276111E01
4.49,1.552 4.677,0.813 4.677,0.813 4.854,0.813 true 0.292,0.927 0.979,1.552 0.688,0.625 10 false Pedestrian Collision 1.271,0.938 2.375,1.573 1.104,0.635 10 false Pressure Change Detection 2.885,0.24 4.24,0.979 1.354,0.74 10 false Pedestrian Protection Sensor LH and RH 5.031,1.406 6.802,1.719 1.771,0.313 10 false Skid Control ECU Assembly 4.917,0.729 6.542,1.073 1.625,0.344 10 false CAN Communication Line 4.604,2.656 6.667,3 2.063,0.344 10 false Pop Up Hood Lifter Assembly RH 0.427,2.635 2.469,2.969 2.042,0.333 10 false Pop Up Hood Lifter Assembly LH 3.156,2.063 3.896,2.646 0.74,0.583 10 false Airbag ECU Assembly



b.

Primary Check Illumination Control

i.

After the ignition switch is turned on (IG), the airbag ECU assembly illuminates the pop up hood warning indicator in the combination meter assembly for approximately 6 seconds and conducts the primary check. During the primary check, the ignition of pop up hood lifters is prohibited and a diagnosis of the airbag ECU assembly is performed. If a malfunction is detected during the primary check, the pop up hood warning indicator will remain on even after 6 seconds have elapsed.

Y220628E04
0.323,0.458 1.448,0.792 1.125,0.333 10 false Ignition Switch 1.542,0.271 2.146,0.552 0.604,0.281 10 false On (IG) 1.76,0.615 2.208,0.906 0.448,0.292 10 false Off 1.75,1.406 2.146,1.698 0.396,0.292 10 false On 1.75,1.74 2.146,2.031 0.396,0.292 10 false Off 0.292,1.542 1.469,2.531 1.177,0.99 10 false Pop Up Hood Warning Indicator 3.021,2.198 4.635,2.646 1.615,0.448 10 false Approximately 6 seconds 4.854,2.073 6.625,2.771 1.771,0.698 10 false ON/OFF condition depends on the primary check result




DIAGNOSIS


a.

If the airbag ECU assembly detects a malfunction in the pop up hood system, the airbag ECU assembly stores the malfunction data in memory in addition to illuminating the pop up hood warning indicator.


b.

The airbag ECU assembly outputs malfunction data and Diagnostic Trouble Codes (DTCs) to the Global TechStream (GTS).


c.

The DTCs can be read by connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.


d.

If the pop up hood lifters deploy, the airbag ECU assembly will turn on the pop up hood warning indicator. However, unlike an ordinary malfunction, a DTC will not be stored. The pop up hood warning indicator cannot be manually turned off. It is necessary to replace the airbag ECU assembly with a new one.