Home › Power Source / Network › POWER DISTRIBUTION › POWER INTEGRATION SYSTEM
NM37H0E _57 Power Source / Network _098048 POWER DISTRIBUTION _0459153 POWER INTEGRATION SYSTEM CO CONTROL F

POWER DISTRIBUTION  POWER INTEGRATION SYSTEM  CONTROL  POWER INTEGRATION CONTROL  


FUNCTION OF MAIN COMPONENTS


*: Models with PTC heater

Components Function
No. 1 Semiconductor Power Integration ECU
·

Receives signals from ECUs and switches, and then drives each component.

·

Shuts off current when a malfunction occurs.

·

Performs multiplex communication with the DLC3 and ECUs.


No. 2 Semiconductor Power Integration ECU
PTC Heater (Quick Heater Assembly)* Generates heat when current is applied, warming the air.
Stop Light Illuminates when the brakes operate.
Center Stop Light Assembly
Back-up Light Illuminates when the shift position is in R.
Taillight
·

Illuminates according to certain conditions when the light control switch is in the TAIL, HEAD or AUTO position.

·

Illuminates when the welcome light illumination operates.


License Plate Light Assembly
Rear Fog Light Illuminates when the rear fog switch is turned on.
Rear Window Defogger Wire Generates heat when current is applied, warming the back window.
Stop Light Switch Assembly Detects the brake pedal condition (on or off) and outputs it to the No. 2 semiconductor power integration ECU.
Shift Control ECU
·

Controls the electronic shift lever system.

·

Outputs reverse signals to the No. 2 semiconductor power integration ECU.


Brake Actuator Assembly
·

No. 2 Skid Control ECU


·

Controls the electronically controlled brake system.

·

Outputs brake light operation requests to the No. 2 semiconductor power integration ECU.


Main Body ECU (Multiplex Network Body ECU)
·

Controls the body control systems.

·

Receives component operation requests and sends them to the semiconductor power integration ECUs.


Air Conditioning Amplifier Assembly
·

Controls the air conditioning system.

·

Sends rear window defogger and PTC heater* operation request signals to the main body ECU.


Steering Sensor Outputs a light control switch position signal to the main body ECU.
Central Gateway ECU (Network Gateway ECU) Relays the signal between the CAN communication lines.
DLC3 Connects to the Global TechStream (GTS).


FUNCTION


Communication Support of Semiconductor Power Integration ECU
Components Semiconductor Power Integration ECU Operation Signal Communication Support
No. 1* No. 2

*: Models with PTC heater

PTC Heater (Quick Heater Assembly)* ○ X ○
Stop Light
Center Stop Light Assembly
X ○ X
Back-up Light X ○ X
Taillight
License Plate Light Assembly
X ○ ○
Rear Fog Light X ○ ○
Rear Window Defogger Wire X ○ ○

HINT:

○: Supported

X: Not supported


a.

Component Operation Output Function

i.

This function turns the corresponding component on and off in accordance with operation signals or switch input signals from the ECU.



b.

Semiconductor Fuse Function

i.

When an abnormal electric current occurs during operation of components, the components are turned off by shutting off the current before electrical wire emits smoke.


ii.

The electrical current is maintained shut off while operation signals or switch signals are on.


iii.

When operation signals or switch signals are turned off, the shut off condition is canceled.

Y204520E02
4.167,3.583 4.344,3.583 4.344,3.583 4.5,3.167 true 2.833,3.563 3.01,3.563 3.01,3.563 3.156,3.167 true 3.646,0.469 4.76,0.771 1.115,0.302 10 false Overcurrent 6.177,0.51 6.698,0.823 0.521,0.313 10 false Normal 1.563,0.458 2.042,0.729 0.479,0.271 10 false Normal 1.063,1.271 1.375,1.469 0.313,0.198 10 false Met 0.167,1.49 0.875,2.146 0.708,0.656 10 false Output On Condition 0.833,1.917 1.406,2.167 0.573,0.25 10 false Not Met 1.125,2.552 1.344,2.76 0.219,0.208 10 false On 1.115,3.198 1.396,3.396 0.281,0.198 10 false Off 0.271,2.906 1.073,3.167 0.802,0.26 10 false Component 2.083,3.469 2.875,3.719 0.792,0.25 10 false Maintaining 3.448,3.5 4.271,3.76 0.823,0.26 10 false Maintaining 3.563,2.188 4.177,2.417 0.615,0.229 10 false Cancel 4.875,2.198 5.469,2.49 0.594,0.292 10 false Cancel



c.

Multiplex Communication Function

i.

Operation Signal Communication

·

This communication uses the multiplex communication line (CXPI communication line) to input operation signals or switch signals from the ECU.



ii.

Diagnosis Communication

·

Checking Diagnostic Trouble Codes (DTCs) regarding ECU and other malfunctions is possible by connecting the Global TechStream (GTS).

·

The semiconductor fuse condition (shut off or not) can be confirmed by connecting the Global TechStream (GTS).



iii.

Reprogramming

·

Reprogramming can be performed by connecting the Global TechStream (GTS).


HINT:

Refer to the Repair Manual for the details of the diagnostic communication and reprogramming.





DIAGNOSIS


a.

In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The Diagnostic Trouble Codes (DTCs) of malfunctions can be read by connecting the Global TechStream (GTS). For details, refer to the Repair Manual.