Home › Vehicle Interior › SEAT › POWER SEAT CONTROL SYSTEM
NM37H0E _58 Vehicle Interior _097224 SEAT _0461873 POWER SEAT CONTROL SYSTEM CO CONTROL F

SEAT  POWER SEAT CONTROL SYSTEM  CONTROL  SEAT CONTROL  


FUNCTION OF MAIN COMPONENTS


Driver Seat
Component Outline

*1: For driver side

*2: Front Multiplex Network Door ECU LH only (LHD models)/ Front Multiplex Network Door ECU RH only (RHD models)

*3: Models with headup display

Position Control ECU Assembly
·

Receives signals from the main body ECU (multiplex network body ECU), etc. via CAN communication and determines operation conditions for the memory system.

·

Inputs signals from the position sensors for the seat adjusters in the driver seat and detects the slide, reclining, front vertical and seat lifter for the driver seat.

·

Receives seat memory switch operation signals from the front multiplex network door ECU*1 via CAN communication and memorizes/recalls the driver seat position.

·

Sounds the built-in buzzer when the memorization operation completes or recall starts.


Main Body ECU (Multiplex Network Body ECU)
·

Inputs signals from the front door courtesy light switch assembly*1 and sends driver door opening and closing signals to the position control ECU assembly via CAN communication.

·

Sends shift position signals from the EV control ECU to the position control ECU assembly via CAN communication.

·

Inputs key ID signals and door lock/unlock signals and sends key ID and door lock/unlock signals to the position control ECU assembly via CAN communication.

·

Detects that the ignition switch is on (IG) and sends signals to the position control ECU assembly via CAN communication.

·

Sends key code confirmation signals to the position control ECU assembly via CAN communication.

·

Inputs signals from the position sensor inside the tilt/telescopic motor and detects the tilt/telescopic position of the steering column.

·

Receives signals (memorization and recall commands) from the position control ECU assembly via CAN communication and memorizes or recalls the steering wheel position.


Multiplex Tilt and Telescopic ECU
·

Inputs rotation angle signals from the tilt motor and telescopic motor and detects the tilt/telescopic position of the steering column.

·

Receives signals (memorize/recall commands) from the multiplex network body ECU via CAN communication and memorizes/recalls the steering position.


Front Door Courtesy Light Switch Assembly*1 Detects the opening and closing of the driver door and sends signals to the main body ECU (multiplex network body ECU).
Front Power Seat Switch*1 Sends signals, which indicate the operation time of each seat adjuster switch of the driver seat, to the position control ECU assembly.
Seat Memory Switch*1 Outputs [Set Memory], [1] or [2] button operation signals to the front multiplex network door ECU*1.
Certification ECU (Smart Key ECU Assembly) Sends smart memory call recall command signals to the main body ECU via CAN communication.
Front Multiplex Network Door ECU LH/RH
·

Inputs signals from each position sensor inside the outer rear view mirror and detects the mirror surface position of the outer rear view mirror.

·

Sends operation signals from the seat memory switch*2 to the main body ECU assembly via CAN communication.


Headup Display (Meter Mirror Sub-assembly)*3
·

Meter Mirror ECU


Receives signals from ECUs and switches and projects various types of vehicle information onto the windshield glass.
EV Control ECU Sends shift position signals to the main body ECU via CAN communication.
DLC3 The DTCs of malfunctioning parts can be read by connecting a diagnostic tool.


OPERATION


a.

Driving Position Memorization Operation

i.

When memorization operation conditions are met, the main body ECU (multiplex network body ECU) sends memorize commands to the position control ECU assembly, multiplex tilt and telescopic ECU and front multiplex network door ECU LH/RH. When the position control ECU assembly, multiplex tilt and telescopic ECU and front multiplex network door ECU LH/RH receive these commands, they memorize the current seat position, steering wheel position, outer rear view mirror surface position and headup display (meter mirror sub-assembly) display position*.

*: Models with headup display



ii.

When driving position memorization is complete, a buzzer sounds for approximately 0.5 seconds.



b.

Driving Position Recall Operation

i.

When driving position recall operation conditions or key OFF recall operation conditions are met and a start recall command signal is received from the main body ECU (multiplex network body ECU), the position control ECU assembly sounds a buzzer for approximately 0.1 seconds, and then drives the seat adjuster motors in the specific recall operation order that was programmed ahead of time, until the current recognized seat position matches the memorized seat position.


ii.

The main body ECU (multiplex network body ECU) sends start recall command signals to the front multiplex network door ECU LH/RH. When the front multiplex network door ECU LH/RH receives start recall command signals, it drives the motors in the specific recall operation order that was programmed ahead of time, until the current recognized mirror surface position matches the memorized mirror surface position.


iii.

When it enters the recall operation step for the steering position, the main body ECU (multiplex network body ECU) sends start recall command signals to the multiplex tilt and telescopic ECU. When the main body ECU recognizes that the recall operation for the steering wheel position is complete based on communication with the multiplex tilt and telescopic ECU, it sends a signal to the position control ECU assembly to start driving the seat adjuster motor that is next in the sequence.


iv.

The main body ECU (multiplex network body ECU) sends start recall command signals to the headup display (meter mirror sub-assembly). When the headup display (meter mirror sub-assembly) receives a start recall command signal, the main body ECU drives the motors in the specific recall operation order that was programmed ahead of time, until the current recognized display position matches the memorized display position.*

*: Models with headup display



v.

If the [1] or [2] button on the seat memory switch is pressed with the ignition switch on (IG) and the shift position in P, the driving position memorized by the system is recalled in the following order.

Driving Position Recall Operation Order
Order Recall Operation Parts
Seat/Steering Outer Rear View Mirror Headup Display*1
(1) Slide Backward Mirror Position Display Position*2
(2) Reclining Backward
(3) Steering Position
(4) Reclining Forward
(5) Slide Forward
(6) Lifter
(7) Front Vertical

HINT:

*1: Models with headup display

*2: The headup display (meter mirror sub-assembly) moves only in the vertical direction.




c.

Driving Position Key OFF Recall Function

i.

Even if the ignition switch is not turned on (IG), if the [1] or [2] button on the seat memory switch is pressed within approximately 180 seconds from the moment the driver door was opened or within approximately 60 seconds from the moment the driver door was closed, the driver seat position is recalled in the same order as the driving position recall function. In this case, the steering wheel position is not recalled unless the ignition switch is turned on (IG) before the driver seat position recall is complete.


ii.

If the ignition switch is turned on (IG) during key OFF recall operation of the driver seat position, the step within the current operation sequence will be completed, the order will be determined with step (3) added, and then the steering wheel position will be recalled.


iii.

If the ignition switch is turned on (IG) when recalling step (6) or (7), step (3) will be recalled immediately.



d.

Memory Call Registration Operation

i.

For electrical keys, if the user pushes the number of the seat memory switch to register while holding the key when memory call operation conditions are met, the memorized driving position is recalled. After recall, the user then presses the lock or unlock button on the door control switch while pressing the number of the seat memory switch again.


ii.

For card keys, the user presses the lock or unlock button on the driver door manual lock switch with the [1] or [2] button on the seat memory switch pressed.


iii.

When the above operation is performed, the main body ECU (multiplex network body ECU) assigns the seat memory switch number and key ID, completing memory call registration.


iv.

When memory call registration is complete, a buzzer sounds for approximately 0.5 seconds.



e.

Memory Call Deregistration Operation

i.

If the user is holding the electrical key when memory call operation conditions are met and then presses the lock or unlock button on the key with the [Set Memory] button on the seat memory switch pressed, or presses the lock or unlock button on the driver door manual lock switch, the position control ECU assembly continues to receive seat memory switch [Set Memory] signals from the front multiplex network door ECU* as it receives key ID signals from the certification ECU.

*: For driver side



ii.

For card keys, the user presses the lock or unlock button on the driver door manual lock switch with the [Set Memory] button on the seat memory switch pressed.


iii.

When the position control ECU assembly receives seat memory switch [Set Memory] signals and key ID signals, it deregisters the memory call for the electrical key that was operated.


iv.

When memory call deregistration is complete, a buzzer sounds twice at approximately 0.1 second intervals. Memory call deregistration will not complete successfully if there are 2 or more electrical keys or card keys in the cabin. In this case, the buzzer sounds for approximately 3 seconds.



f.

Memory Call Recall Operation

i.

If the door is unlocked using the smart door unlock function (or the unlock switch on the electrical key) when memory call operation conditions are met, the main body ECU (multiplex network body ECU) receives key ID signals and door unlock signals.


ii.

If the driver door is opened in this state, the main body ECU (multiplex network body ECU) starts the memory call recall operation via CAN communication.


iii.

When memory call recall starts, a buzzer sounds for approximately 0.1 seconds.


iv.

This supports the customization function via diagnostic tool or operation of the multi display screen, and it is possible to change the memory call-linked door setting from "driver door" to "all doors" (driver door and front passenger door). Refer to the Repair Manual for details on the customization function.




FUNCTION


a.

Driving Position Memorization Function

i.

The [1] or [2] button is pressed*2 within approximately 3 seconds after pressing the [Set Memory] button with the ignition switch on (IG)*1, the driving position (driver seat slide, reclining, front vertical, lifter, steering column tilt and telescopic and outer rear view mirror surface positions) when the switch was pressed is memorized by the system.

HINT:

*1: If the front power seat switch, tilt and telescopic switch or door mirror switch is being operated, or the headup display (meter mirror sub-assembly) (for models with a headup display (meter mirror sub-assembly)) position setting is being operated, the position of the part being operated is not be memorized. The positions of parts not being operated by switch are memorized and the buzzer sounds. Memorization operations are disabled during driving position recall operation. In this case, either stop operating each switch, or operate after the recall operation is complete.




b.

Driving Position Recall Function

i.

If the [1] or [2] button on the seat memory switch LH/RH is pressed with the ignition switch on (IG) and the shift position in P, the driving position memorized by the system is recalled in the following order.

V129163C01
5.219,2.094 5.417,2.26 0.198,0.167 10 true *a 4.656,2.917 4.844,3.083 0.188,0.167 10 true *b 5.583,4.271 5.781,4.448 0.198,0.177 10 true *c 3.594,3.917 3.823,4.104 0.229,0.188 10 true *d 4.042,2.771 4.271,2.969 0.229,0.198 10 true *e 4.365,1.135 4.677,1.292 0.313,0.156 10 false *f 5.813,1.094 6.313,1.292 0.5,0.198 10 true *g (*A) 1.531,2.333 1.771,2.552 0.24,0.219 10 true *h 0.188,5.438 0.5,5.594 0.313,0.156 10 false *i
*A Models with head up display - -
*a Steering Tilt/Telescopic Position *b Front Vertical Position
*c Seat Slide Position *d Lifter Position
*e Reclining Position *f Outer Rear View Mirror Position
*g Head up Display Position *h Seat Memory Switch
*i The illustrations shown are examples only. - -




c.

Driving Position Key OFF Recall Function

i.

Even if the ignition switch is not turned on (IG), if the [1] or [2] button on the seat memory switch is pressed within approximately 180 seconds from the moment the driver door was opened or within approximately 60 seconds from the moment the driver door was closed, the driver seat position is recalled in the same order as the driving position recall function. In this case, the steering wheel position is not recalled unless the ignition switch is turned on (IG) before the driver seat position recall is complete.


ii.

If the ignition switch is turned on (IG) during key OFF recall operation of the driver seat position, the step within the current operation sequence will be completed, the order will be determined with step (3) added, and then the steering wheel position will be recalled.


iii.

If the ignition switch is turned on (IG) when recalling step (6) or (7), step (3) will be recalled immediately.



d.

Power easy access systems (Models with power easy access systems)

i.

Power easy access systems are provided for the driver seat. These systems are making it easier to enter and exit the vehicle.


ii.

The away operation is performed when a passenger exits the vehicle. The steering wheel is moved to the maximum tilt level and the maximum telescopic contraction position, the driver seat is slid to the rear. The return operation is performed when a passenger enters the vehicle. The driver seat and steering wheel move back to the position they were in prior to the away operation.




DIAGNOSIS


a.

The position control ECU assembly (front power seat switch) has a diagnosis function. It stores a record of any power seat control system malfunctions in its memory in the form of Diagnostic Trouble Codes (DTCs).