Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › DYNAMIC RADAR CRUISE CONTROL SYSTEM
NM37H0E _95 ADAS / AD _097337 ADVANCED DRIVER ASSISTANCE SYSTEM _0462892 DYNAMIC RADAR CRUISE CONTROL SYSTEM CO CONTROL F

ADVANCED DRIVER ASSISTANCE SYSTEM  DYNAMIC RADAR CRUISE CONTROL SYSTEM  CONTROL  DYNAMIC RADAR CRUISE CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components in the dynamic radar cruise control system have the following functions:

Component Function

*1: Models with RSA system

*2: Models with headup display

Millimeter Wave Radar Sensor Assembly Radiates millimeter radar waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead, the vehicle-to-vehicle distance, and the relative speed, and then sends this information to the forward recognition camera.
Forward Recognition Camera
·

Detects lane markers and objects on the road ahead using the image captured by the camera sensor.

·

While the system is in vehicle-to-vehicle distance control mode, the forward recognition camera detects the vehicle ahead based on signals from the millimeter wave radar sensor and forward recognition camera. Then, the forward recognition camera calculates the acceleration or deceleration rate required in order to attain the target vehicle-to-vehicle distance, and outputs a request signal to the EV control ECU.

·

Controls the supply of electric current to the camera heater when the ambient temperature is low.

·

If the detects a malfunction in the dynamic radar cruise control system, it will store Diagnostic Trouble Codes (DTCs).


Camera Heater (Forward Recognition Hood with Heater Sub-assembly) Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up.
Steering Pad Switch Assembly Cruise Control Main Switch
·

Turns the cruise control system on and off.

·

Vehicle-to-vehicle distance control mode becomes be activated immediately after the switch is turned on. The mode shifts to constant speed control mode by pressing and holding the switch more than 1.5 seconds.


CANCEL Switch A cancel signal is output to the EV control ECU when this switch is operated.
+RES Switch
·

The acceleration function and resuming of a preset speed can be performed by operating this switch. A signal is output to the EV control ECU when this switch is operated.

·

The dynamic radar cruise control with road sign assist operation signals are sent to the EV control ECU.*1


-SET Switch
·

The deceleration function and vehicle speed setting resume signals are output to the EV control ECU when this switch is operated.

·

The dynamic radar cruise control with road sign assist operation signals are sent to the EV control ECU.*1


Vehicle-to-vehicle Distance Control Switch While the system is in vehicle-to-vehicle distance control mode, the driver can operate the vehicle-to-vehicle distance control switch to select the vehicle-to-vehicle distance in 3 levels: long, middle and short.
Stop Light Switch Assembly Detects brake pedal depression and transmits its signal to the EV control ECU.
Shift Lever Position Sensor Detects the shift lever position and transmits signals to the EV control ECU.
Turn Signal Switch Sends a turn signal command to the EV control ECU.
Electric Parking Brake Switch Detects the switch condition and transmits signals to the No. 2 skid control ECU.
Accelerator Pedal Sensor Assembly Detects the accelerator pedal depression angle and transmits it to the EV control ECU.
Steering Sensor Detects the angle and direction of steering and sends signals to the EV control ECU.
Airbag ECU (Airbag ECU Assembly) Yawrate Sensor Detects the yaw rate of the vehicle and sends signals to the EV control ECU.
Inverter with Converter Assembly MG ECU Controls the motive force of FCV transaxle with motor assembly in accordance with signals from the EV control ECU.
FCV Transaxle with Motor Assembly Traction Motor Generates motive force for the front wheels.
Combination Meter Assembly Cruise Control Indicator (Constant Speed Control Mode)
·

Based on a cruise control indicator (constant speed control mode) operation signal sent by the EV control ECU, the combination meter assembly illuminates the cruise control indicator (constant speed control mode) when the dynamic radar cruise control system in constant speed control mode has been turned on using the cruise control main switch on the steering pad switch assembly.

·

Based on a cruise control indicator (constant speed control mode) operation signal sent by the EV control ECU, the combination meter assembly turns off the cruise control indicator light if a malfunction occurs in the dynamic radar cruise control system.


Cruise Control Indicator (Vehicle-to-vehicle Distance Control Mode)
·

Based on a cruise control indicator (vehicle-to-vehicle distance control mode) operation signal sent by the EV control ECU, the combination meter assembly illuminates the cruise control indicator (vehicle-to-vehicle distance control mode) when the dynamic radar cruise control system in vehicle-to-vehicle distance control mode has been turned on using the cruise control main switch on the steering pad switch assembly.

·

Based on a cruise control indicator (vehicle-to-vehicle distance control mode) operation signal sent by the EV control ECU, the combination meter assembly turns off the cruise control indicator (vehicle-to-vehicle distance control mode) if a malfunction occurs in the dynamic radar cruise control system.


Cruise SET Indicator Cruise SET indicator illuminates when the vehicle speed is set.
Multi-information Display
·

Displays a warning message to alert the driver in accordance with a signal provided by the EV control ECU.

·

During dynamic radar cruise control operation, the multi-information display receives signals from the EV control ECU in order to display the system conditions.


Buzzer
·

Sounds a buzzer when it receives a signal from the EV control ECU to alert the driver that the distance between vehicles is short.

·

If the EV control ECU detects automatic cancel or warning signals while the vehicle is operating under cruise control, this buzzer sounds to inform the driver.


Headup Display (Meter Mirror Sub-assembly)*2 The headup display receives signals from the EV control ECU in order to display the system conditions.
EV Control ECU
·

Controls the dynamic radar cruise control system in accordance with signals from switches, sensors.

·

If the EV control ECU detects a malfunction in the dynamic radar cruise control system, it will store Diagnostic Trouble Codes (DTCs).


No. 2 Skid Control ECU
·

While the system is operating in vehicle-to-vehicle distance control mode, the No. 2 skid control ECU operates the brake actuator in accordance with the brake request signal received from the EV control ECU.

·

Applies the brakes in accordance with signals from the EV control ECU.


Central Gateway ECU (Network Gateway ECU) Transmits the signal between the CAN communication buses.
DLC3 The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions.



SYSTEM CONTROL


a.

The control of the dynamic radar cruise control system varies depending on the mode:

A: Constant Speed Control Mode

B: Vehicle-to-vehicle Distance Control Mode

Function Outline Mode
A B

*: Models with RSA system

Constant Speed Control The EV control ECU compares the actual vehicle speed and the set speed and if the vehicle speed is lower than the set speed, it accelerates the vehicle by adjusting the respective motive forces. ○ ○
Deceleration Control Performs motive force control and brake control in order to decelerate the vehicle so that the vehicle-to-vehicle distance between the driver's own vehicle and the vehicle ahead is maintained at the set distance. - ○
Follow-up Control After performing deceleration control, the driver's own vehicle follows the vehicle ahead in order to maintain the proper vehicle-to-vehicle distance. The actual distance maintained for each distance level (long, medium and short) varies in accordance with the vehicle speed. - ○
Acceleration Control Accelerates the vehicle in order to attain the set vehicle speed if the vehicle ahead or the driver's own vehicle has changed lanes. - ○
Stop Control Detects if the vehicle ahead has stopped, performs motive force control and stops the vehicle while maintaining proper vehicle-to-vehicle distance. - ○
Stop Retention Control Judges if the vehicle is stopped, performs brake control and keeps the vehicle stopped through the brake hold function. - ○
Start Control Detects that the vehicle ahead starts moving again, displays the message on the multi-information display to urge the driver to perform the start-off operation (to operate the +RES switch on the steering pad switch assembly or depress the accelerator pedal), and resumes follow-up control after the vehicle is started. - ○
Turn signal-linked Control If the turn signal switch is operated when changing lanes to the passing lane at a vehicle speed of approximately 80 km/h (50 mph) during follow-up control, the vehicle will begin preliminary acceleration; once the vehicle has changed lanes it will first maintain this preliminary acceleration, and then slowly accelerate to the set vehicle speed. - ○
Dynamic Radar Cruise Control with Road Sign Assist* This function is turned on and while RSA system speed limit information is displayed, the speed limit can be set by holding down the +RES switch to increase the set vehicle speed to the speed limit, or by holding down the -SET switch to reduce the set vehicle speed to the speed limit. - ○
Curve Speed Reduction Control When the system determines that it is necessary to restrain the vehicle speed due to a curve, the system uses motive force control and brake control to perform speed restraint. - ○
Excessive Speed Warning If the vehicle has exceeded the set vehicle speed in the following conditions, the display of the set vehicle speed is inverted.
·

When the accelerator pedal is depressed and the vehicle is being accelerated

·

When driving on a downhill slope


○ ○
Set Control When the dynamic radar cruise control system has been turned on using the cruise control main switch on the steering pad switch assembly, either of the relevant vehicle speed conditions shown below is met, and the -SET switch on the steering pad switch assembly is pressed, the EV control ECU stores the vehicle speed and maintains the vehicle constantly at that speed. ○ ○
The vehicle is being driven at a speed of approximately 30 km/h (20 mph) or more. ○ ○
When the vehicle is traveling at a speed of approximately 30 km/h (20 mph) or less and a vehicle ahead is detected, the set vehicle speed is set to the low speed limit [approximately 30 km/h (20 mph)]. - ○
Low Speed Limit Control The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approximately 30 km/h (20 mph). The cruise control cannot be set below that speed. If the vehicle speed drops below that speed while driving using cruise control, the cruise control will be canceled automatically. The set vehicle speed is kept in memory. ○ -
COAST Control While the -SET switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows, according to the mode: ○ ○
·

The vehicle decelerates constantly.

·

The set vehicle speed changes to the speed at which the -SET switch is released.


○ -
·

The set vehicle speed decreases in increments of 5 km/h or 5 mph. [Example: 103 →100 → 95 → 90 → 85 km/h (mph)]

·

The vehicle decelerates rapidly. The vehicle will remain at the speed that the vehicle is traveling at when the -SET switch is released.


- ○
Tap Down Control When the -SET switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows, according to the mode: ○ ○
·

The vehicle will decelerate in increments of approximately 1 km/h or 1 mph each time the -SET switch is pushed.

·

However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will change to the speed at which the vehicle was being driven at the time the -SET switch was operated.


○ -
The vehicle will decelerate in increments of approximately 1 km/h or 1 mph for each time the -SET switch is pushed. - ○
Accelerator Control While the +RES switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows, according to the mode: ○ ○
·

The vehicle will accelerate constantly.

·

The set vehicle speed changes to the speed at which the +RES switch is released.


○ -
·

The set vehicle speed increases in increments of 5 km/h or 5 mph. [Example: 83 → 85 → 90 → 95 → 100 km/h (mph)]

·

The vehicle will accelerate to the speed that is set at the time the +RES switch is released. However, only the set vehicle speed will change during follow-up control.


- ○
If the -SET switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less) when the vehicle speed is increased by pressing the acceleration pedal, the system will memorize the set vehicle speed at that speed. ○ ○
Tap Up Control When the +RES switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows: ○ ○
·

The vehicle will accelerate in increments of approximately 1 km/h or 1 mph for each time the +RES switch was pushed.

·

However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will not change.


○ -
The vehicle will accelerate in increments of approximately 1 km/h or 1 mph for each time the +RES switch is pushed. - ○
Resume Control If the vehicle speed is above the low speed limit, the +RES switch on the steering pad switch assembly can be pushed to resume cruise control operation and reach the vehicle speed that was set at the time the driver canceled cruise control. ○ ○
If the vehicle ahead changes driving lanes during follow-up control, the vehicle speed is gradually increased to the set vehicle speed. - ○
After the vehicle ahead has started running again under stop retention control and then the message that urges the driver to perform the start-off operation has been displayed, when the steering pad switch assembly is pushed to the +RES switch, follow-up control is resumed and the vehicle can be accelerated up to the set speed. - ○
Manual Cancel Control If any of the following signals are sent to the EV control ECU, the cruise control is canceled accordingly:
·

Stop light switch on signal. (The brake pedal is depressed)

·

Shift position is changed from D to any other position.

·

CANCEL switch on signal. (CANCEL switch on the steering pad switch assembly is pushed)

·

Cruise control main switch off signal. (Cruise control main switch on the steering pad switch assembly is pushed)

·

Electric parking brake is applied. (Only during vehicle-to-vehicle distance control mode)


○ ○
Automatic Cancel Control When an automatic cancel signal is sent to the EV control ECU, cruise control operation is canceled. At this time, the type of warning sent to the driver and the control resumption condition varies according to the cancel signal. ○ ○
Mode Switching Control The following operations switch modes:
·

Vehicle-to-vehicle distance control mode is activated immediately after the switch is turned on. The mode is changed to constant speed control mode by pressing and holding the switch for more than 1.5 seconds while the dynamic radar cruise control system is turned off.


○ ○
Other Cancel Conditions If any of the following conditions occur during cruise control driving, speed control by the dynamic radar cruise control system is canceled.
However, the set speed remains in the memory:
·

VSC operates during cruise control driving.

·

TRC operates for a certain period of time during cruise control driving.

·

TRC is off or VSC is off.

·

Drive start control operates during cruise control driving.

·

Pre-collision system operates during cruise control driving.

·

Parking support brake system operates during cruise control driving.


○ ○
Diagnosis If a malfunction occurs in the dynamic radar cruise control system during cruise control operation, the EV control ECU cancels cruise control and memorizes information related to the malfunction. ○ ○

HINT:

○: Available

-: Not available


i.

Constant Speed Control Mode

·

The EV control ECU compares the set vehicle speed and the actual vehicle speed, and performs constant speed control in order to attain the set vehicle speed.



ii.

Vehicle-to-vehicle Distance Control Mode

·

In vehicle-to-vehicle distance control mode, the EV control ECU performs constant speed control function, deceleration control function, follow-up control function, acceleration control function, stop control function, stop retention control function, start control function, turn signal-linked control function or dynamic radar cruise control with road sign assist* based on the information about the vehicle ahead transmitted from the millimeter wave radar sensor assembly and forward recognition camera.

*: Models with RSA system



1.

Constant Speed Control Function

(a)

The EV control ECU compares the set vehicle speed and the actual vehicle speed, and performs constant speed control by regulating the motive force in order to attain the set vehicle speed. The forward recognition camera uses the millimeter wave radar sensor assembly signal and information from the forward recognition camera to determine the condition in front of the vehicle and sends acceleration/deceleration requests to the EV control ECU.

Y242021E01
0.76,2.073 2.448,2.271 1.688,0.198 10 false Own Vehicle 1.531,0.229 3.646,0.458 2.115,0.229 10 false Forward Recognition Camera 4.531,0.229 6.427,0.688 1.896,0.458 10 false Millimeter Wave Radar Sensor Assembly 2.813,1.427 4.021,1.698 1.208,0.271 10 false EV Control ECU 4.521,1.406 6.208,1.604 1.688,0.198 10 false Acceleration Control 4.906,1.844 6.594,2.042 1.688,0.198 10 false MG ECU 4.906,2.167 6.594,2.365 1.688,0.198 10 false - Motor Control


2.

Deceleration Control Function

(a)

The forward recognition camera calculates the target deceleration rate in accordance with signals from the millimeter wave radar sensor assembly, forward recognition camera and transmits a deceleration request signal to the EV control ECU. Upon receiving this signal, the EV control ECU performs traction motor and brake control in order to cause the vehicle to decelerate.

(b)

This control is not performed in the presence of a parked vehicle or object or below the settable vehicle speed range.

Y242022E03
0.76,0.75 2.75,0.948 1.99,0.198 10 false Vehicle Ahead 0.76,2.708 2.75,2.906 1.99,0.198 10 false Own Vehicle 1.49,0.24 3.479,0.438 1.99,0.198 10 false Forward Recognition Camera 2.823,1.438 4.813,1.635 1.99,0.198 10 false EV Control ECU 4.51,0.24 6.417,0.635 1.906,0.396 10 false Millimeter Wave Radar Sensor Assembly 4.51,1.063 6.5,1.26 1.99,0.198 10 false Acceleration Control 4.875,1.531 6.865,1.729 1.99,0.198 10 false MG ECU 4.885,1.833 6.875,2.031 1.99,0.198 10 false - Motor Control 4.51,2.406 6.5,2.604 1.99,0.198 10 false Deceleration Control 4.865,2.844 6.396,3.135 1.531,0.292 10 false No. 2 Skid Control ECU 4.875,3.167 6.865,3.365 1.99,0.198 10 false - Brake Control

(c)

If the forward recognition camera determines that further deceleration is necessary, it transmits a brake request signal to the EV control ECU. Upon receiving this signal, the EV control ECU transmits a brake request signal to the No. 2 skid control ECU. The No. 2 skid control ECU then controls the brake actuator to apply the brakes.

(d)

At this time, if the deceleration rate is higher than a predetermined value, the No. 2 skid control ECU outputs a stop light illumination request signal to the stop lights in order to warn any vehicles behind.

Y242023E03
0.875,0.75 2.865,0.948 1.99,0.198 10 false Vehicle Ahead 0.76,2.958 2.75,3.156 1.99,0.198 10 false Vehicle Behind 1.583,0.292 3.573,0.49 1.99,0.198 10 false Forward Recognition Camera 3.052,1.438 5.042,1.635 1.99,0.198 10 false EV Control ECU 4.573,0.24 6.479,0.635 1.906,0.396 10 false Millimeter Wave Radar Sensor Assembly 4.604,1.063 6.594,1.26 1.99,0.198 10 false Acceleration Control 5.031,1.479 6.323,1.698 1.292,0.219 10 false MG ECU 5.031,1.792 7.021,1.99 1.99,0.198 10 false - Motor Control 4.604,2.354 6.594,2.552 1.99,0.198 10 false Deceleration Control 5.031,2.802 7.021,3 1.99,0.198 10 false No. 2 Skid Control ECU 5.031,3.104 7.021,3.302 1.99,0.198 10 false - Brake Control 0.76,1.906 2.75,2.104 1.99,0.198 10 false Own Vehicle

(e)

If the vehicle is not decelerating adequately, the EV control ECU sounds a buzzer. The buzzer is sounded to urge the driver to depress the brake pedal.

Y242024E03
0.917,1.458 2.906,1.656 1.99,0.198 10 false Vehicle Ahead 0.771,2.698 2.76,2.896 1.99,0.198 10 false Own Vehicle 0.771,3.771 2.76,3.969 1.99,0.198 10 false Vehicle Behind 1.344,0.25 3.333,0.448 1.99,0.198 10 false Forward Recognition Camera 2.906,2.344 4.896,2.542 1.99,0.198 10 false EV Control ECU 4.49,0.229 6.375,0.656 1.885,0.427 10 false Millimeter Wave Radar Sensor Assembly 4.5,1 6.49,1.198 1.99,0.198 10 false Warning 4.781,1.385 6.771,1.583 1.99,0.198 10 false Buzzer 4.5,1.948 6.49,2.146 1.99,0.198 10 false Acceleration Control 4.979,2.385 6.969,2.583 1.99,0.198 10 false MG ECU 4.5,3.313 6.49,3.51 1.99,0.198 10 false Deceleration Control 4.781,3.781 6.771,3.979 1.99,0.198 10 false No. 2 Skid Control ECU 4.979,2.719 6.969,2.917 1.99,0.198 10 false - Motor Control 4.792,4.135 6.781,4.333 1.99,0.198 10 false - Brake Control


3.

Follow-up Control Function

(a)

After performing deceleration control, the forward recognition camera transmits request signals to the EV control ECU so that the vehicle can follow the vehicle ahead while maintaining the proper vehicle-to-vehicle distance according to the vehicle speed. Upon receiving these signals, these ECUs control the motive force in order to perform follow-up control.

(b)

3 stages (long, middle and short) of vehicle-to-vehicle distance can be selected by operating the vehicle-to-vehicle distance control switch.

Y242025E03
1.354,0.552 3.677,0.771 2.323,0.219 10 false Forward Recognition Camera 4.427,0.573 6.333,0.948 1.906,0.375 10 false Millimeter Wave Radar Sensor Assembly 4.448,1.375 6.771,1.594 2.323,0.219 10 false Steering Pad Switch Assembly 4.552,1.906 6.719,2.302 2.167,0.396 10 false Vehicle-to-vehicle Distance Control Switch 4.458,2.792 6.781,3.01 2.323,0.219 10 false Acceleration Control 4.729,3.229 7.052,3.448 2.323,0.219 10 false MG ECU 4.729,3.563 7.052,3.781 2.323,0.219 10 false - Motor Control 4.448,4.063 6.771,4.281 2.323,0.219 10 false Deceleration Control 4.729,4.479 7.052,4.698 2.323,0.219 10 false No. 2 Skid Control ECU 4.729,4.823 7.052,5.042 2.323,0.219 10 false - Brake Control 2.906,3.229 4.125,3.5 1.219,0.271 10 false EV Control ECU 0.771,2 2,2.271 1.229,0.271 10 false Vehicle Ahead 0.76,3.5 1.927,3.75 1.167,0.25 10 false Own Vehicle 0.958,2.719 2.073,3.094 1.115,0.375 10 false Vehicle-to-vehicle Distance


4.

Acceleration Control Function

(a)

If the forward recognition camera detects (based on the millimeter wave radar sensor assembly and forward recognition camera) that either the vehicle ahead or the driver has changed lanes, an acceleration request signal is transmitted to the EV control ECU in order to attain the set vehicle speed. Upon receiving this signal, the EV control ECU controls the motive force of the traction motor in order to perform acceleration control.

Y242026E01
1.76,0.25 3.688,0.49 1.927,0.24 10 false Forward Recognition Camera 4.417,0.25 6.969,0.531 2.552,0.281 10 false Millimeter Wave Radar Sensor Assembly 4.448,1.354 5.865,1.594 1.417,0.24 10 false Acceleration Control 4.896,1.833 5.656,2.042 0.76,0.208 10 false MG ECU 4.896,2.146 6,2.417 1.104,0.271 10 false - Motor Control 2.833,1.375 4.063,1.833 1.229,0.458 10 false EV Control ECU 1.271,1.354 2.25,1.615 0.979,0.26 10 false Vehicle Ahead 0.76,2.781 1.74,3.042 0.979,0.26 10 false Own Vehicle


5.

Stop Control Function

(a)

During vehicle-to-vehicle distance control mode, if the vehicle ahead stops, the forward recognition camera maintains an appropriate vehicle-to-vehicle distance while at the same time calculating the necessary driving force to stop the vehicle, and sends a drive request signal to the EV control ECU and No. 2 skid control ECU. When the EV control ECU and No. 2 skid control ECU receive this signal, they control the motive force and stop the vehicle.

(b)

At this time, the No. 2 skid control ECU outputs a stop light illumination request signal in order to inform anyone who might be following the vehicle.

(c)

The distance between the driver's own vehicle and the preceding vehicle when the vehicles are stopped is set to approximately 3 m to 5 m (10 ft. to 16 ft.) regardless of the vehicle-to-vehicle distance preset by using the vehicle-to-vehicle distance control switch.

Y275735E01
1.833,0.354 3.667,0.76 1.833,0.406 10 false Forward Recognition Camera 4.865,0.385 6.74,0.792 1.875,0.406 10 false Millimeter Wave Radar Sensor Assembly 3.063,2.104 4.167,2.448 1.104,0.344 10 false EV Control ECU 5.156,1.458 6.521,1.781 1.365,0.323 10 false Acceleration Control 5.063,2.313 5.802,2.563 0.74,0.25 10 false MG ECU 5.25,2.688 6.729,2.906 1.479,0.219 10 false - Motor Control 4.583,3.885 6.063,4.094 1.479,0.208 10 false Deceleration Control 3.813,4.438 4.979,4.844 1.167,0.406 10 false No. 2 Skid Control ECU 5.896,4.74 6.906,4.979 1.01,0.24 10 false Stop Light On 0.896,4.26 2.083,4.49 1.188,0.229 10 false Vehicle Behind 0.896,1.833 2.083,2.063 1.188,0.229 10 false Vehicle Ahead 0.896,3.115 2.083,3.344 1.188,0.229 10 false Own Vehicle


6.

Stop Retention Control Function

(a)

After the vehicle has stopped under stop control, EV control ECU transmits a stop retention request signal to the No. 2 skid control ECU. Upon receiving this signal, the No. 2 skid control ECU activates the brake hold function and keeps the vehicle stopped.

HINT:

If the vehicle ahead starts off within approximately 3 seconds after own vehicle stops, follow-up cruising will be resumed.


Y230951E08
3.052,1.927 4.135,2.448 1.083,0.521 10 false EV Control ECU 1.552,0.427 3.49,0.729 1.938,0.302 10 false Forward Recognition Camera 4.292,0.438 6.844,0.885 2.552,0.448 10 false Millimeter Wave Radar Sensor Assembly 1.052,1.802 2.104,2.198 1.052,0.396 10 false Vehicle Ahead 0.99,3.281 2.042,3.677 1.052,0.396 10 false Own Vehicle 4.26,3.302 5.833,3.563 1.573,0.26 10 false Stop Retention Control 3.313,3.802 4.76,4.073 1.448,0.271 10 false No. 2 Skid Control ECU 3.49,4.104 4.646,4.375 1.156,0.271 10 false - Brake Control 5.573,3.729 6.729,4 1.156,0.271 10 false Stop Holding 5.604,4.188 6.583,4.458 0.979,0.271 10 false Stop Light On


7.

Start Control Function

(a)

When the forward recognition camera detects that the vehicle ahead starts moving again from the millimeter wave radar sensor assembly and forward recognition camera signal, it displays the messages on the multi-information display to urge the driver to perform the start-off operation (to push the +RES switch or depress the accelerator pedal).

(b)

Upon receiving the start-off operation signal generated by pushing the +RES switch on the steering pad switch assembly or by depressing the accelerator pedal, the forward recognition camera transmits a motive force request signal to the EV control ECU. Upon receiving this signal, the EV control ECU controls the motive force, starts the vehicle and resumes follow-up control.

HINT:

Pressing the +RES switch while the vehicle ahead stops will resume follow-up cruising if the vehicle ahead starts off within approximately 3 seconds after the switch is pressed.


Y275736E01
1.688,0.25 3.5,0.594 1.813,0.344 10 false Forward Recognition Camera 4.729,0.219 6.625,0.688 1.896,0.469 10 false Millimeter Wave Radar Sensor Assembly 3.208,1.406 7.146,1.823 3.938,0.417 10 false Start-off Operation Request Display on Multi-information Display 3.823,2.167 6.5,2.458 2.677,0.292 10 false Steering Pad Switch (+RES Switch Signal) 3.5,1.781 5.771,1.969 2.271,0.188 10 false Accelerator Pedal Operation Signal 2.698,3.354 3.771,3.844 1.073,0.49 10 false EV Control ECU 4.698,3.365 5.688,3.521 0.99,0.156 10 false MG ECU 5.073,2.802 6.604,3 1.531,0.198 10 false Acceleration Control 4.333,5.063 6.052,5.313 1.719,0.25 10 false Stop Retention Control 3.031,5.604 4.75,5.854 1.719,0.25 10 false No. 2 Skid Control ECU 3.448,6.104 4.688,6.354 1.24,0.25 10 false - Brake Control 5.865,5.604 6.719,5.844 0.854,0.24 10 false Stop Holding 5.854,6.115 6.833,6.344 0.979,0.229 10 false Stop Light Off 0.74,4.521 1.802,4.76 1.063,0.24 10 false Own Vehicle 0.75,2.625 1.813,2.865 1.063,0.24 10 false Vehicle Ahead 4.76,3.74 6.813,3.979 2.052,0.24 10 false - Motor Control


8.

Turn signal-linked Control Function

(a)

If the turn signal switch is operated when changing lanes to the passing lane at a vehicle speed of approximately 80 km/h (50 mph) during follow-up control, the vehicle will begin preliminary acceleration; once the vehicle has changed lanes it will first maintain this preliminary acceleration, and then slowly accelerate to the set vehicle speed.

Y242027E01
1.76,0.781 3.75,0.979 1.99,0.198 10 false Vehicle Ahead 3.979,0.771 5.969,0.969 1.99,0.198 10 false Vehicle Ahead 6.344,0.969 6.854,1.417 0.51,0.448 10 false Vehicle Ahead 1.76,2.458 3.75,2.656 1.99,0.198 10 false Own Vehicle 3.979,2.146 5.969,2.344 1.99,0.198 10 false Own Vehicle 4.698,1.865 6.688,2.063 1.99,0.198 10 false Own Vehicle 0.74,3.458 2.031,3.938 1.292,0.479 10 false Forward Recognition Camera 2.833,3.521 5.573,3.781 2.74,0.26 10 false Millimeter Wave Radar Sensor Assembly 2.833,4.417 5.323,4.646 2.49,0.229 10 false Headlight Dimmer Switch Assembly 2.49,5.094 3.573,5.479 1.083,0.385 10 false EV Control ECU 4.177,5.094 6.167,5.292 1.99,0.198 10 false Acceleration Control 4.458,5.531 6.448,5.729 1.99,0.198 10 false MG ECU 4.458,5.844 6.448,6.042 1.99,0.198 10 false - Motor Control


9.

Dynamic Radar Cruise Control with Road Sign Assist (Models with RSA System)

(a)

This function is turned on and while RSA system speed limit information is displayed, the speed limit can be set by holding down the +RES switch to increase the set vehicle speed to the speed limit, or by holding down the -SET switch to reduce the set vehicle speed to the speed limit.

Y242028E01
3.865,0.375 6.75,0.948 2.885,0.573 10 false Operation Request Display on Multi-information Display 5.104,1.01 6.781,1.281 1.677,0.271 10 false +RES/-SET Switch Signal 4.99,2.135 6.292,2.458 1.302,0.323 10 false Acceleration Control 5.271,2.573 5.979,2.823 0.708,0.25 10 false MG ECU 5.271,2.906 6.333,3.135 1.063,0.229 10 false - Motor Control 3.344,2.156 4.719,2.573 1.375,0.417 10 false EV Control ECU 1.167,2.615 2.469,3.073 1.302,0.458 10 false Forward Recognition Camera


10.

Curve Speed Reduction Control

(a)

When the system determines that it is necessary to restrain the vehicle speed according to information from the sensors while driving in vehicle-to-vehicle distance control mode, displays on the headup display* and multi-information display are used to inform the driver that the curve speed reduction control function is operating.

*: Models with headup display


(b)

When control performed by the curve speed reduction control function completes, the display turns off and the vehicle returns to the set speed of the radar cruise control system according to the conditions.

Y251787E02
1.729,3.135 2.146,2.031 2.146,2.031 2.438,2.031 true 2.479,1.927 4.365,2.458 1.885,0.531 10 false Starts decelerating based on information from sensors 0.24,3.51 3.5,3.771 3.26,0.26 10 false This illustration is only for explanatory purposes.


11.

Excessive Speed Warning

(a)

If the vehicle has exceeded the set vehicle speed in the following conditions, the display of the set vehicle speed is inverted.

(1)

When the accelerator pedal is depressed and the vehicle is being accelerated

(2)

When driving on a downhill slope





iii.

Automatic Cancel Control

·

If one of the conditions listed below occurs while the vehicle is being driven using cruise control, speed control by the cruise control system will be canceled. Then, the following warning items will appear for the driver.

Constant Speed Control Mode
Situation Warning
Multi-information Display Buzzer
If the following condition occurs, the EV control ECU clears the set vehicle speed and cancels the cruise control.
·

An open or short circuit in the stop light switch assembly.


The dynamic radar cruise control system is disabled until the ignition switch is turned ON again.
Cruise Control
Malfunction
Visit Your Dealer
Sounds
If the following condition occurs, the EV control ECU clears the set vehicle speed and cancels the cruise control.
·

The vehicle speed drops more than 16 km/h (10 mph) below the set vehicle speed.


- -
If the following condition occurs, the EV control ECU cancels the cruise control while retaining the set vehicle speed in its memory.
·

The vehicle speed drops below the low speed limit [approximately 30 km/h (20 mph)].


- -
If the following condition occurs, the EV control ECU clears the set vehicle speed and cancels the cruise control.
·

Malfunction in the FC system.


The dynamic radar cruise control system is disabled until the ignition switch is turned ON again.
- -
If either of the conditions listed below occurs, the EV control ECU clears the set vehicle speed and cancels the cruise control.
·

Stop light switch assembly input signal is abnormal.

·

Cancel circuit malfunction.

·

Brake control system malfunction.

·

Communication malfunction between the No. 2 skid control ECU and EV control ECU.


Cruise Control
Malfunction
Visit Your Dealer
Sounds

Vehicle-to-vehicle Distance Control Mode
Situation Warning
Multi-information Display Buzzer

*: During stop retention control

If either of the conditions listed below occurs, the EV control ECU clears the set vehicle speed and cancels the cruise control.
·

An open or short circuit in the stop light switch assembly.

·

Malfunction of the millimeter wave radar sensor assembly.

·

Misalignment of the axis of the millimeter wave radar sensor assembly.

·

The brake holding control system is malfunction.

·

Malfunction in the dynamic radar cruise control system other than those given above.


The dynamic radar cruise control system is disabled until the ignition switch is turned ON again.
Cruise Control
Malfunction
Visit Your Dealer
Sounds
If the following condition occurs, the EV control ECU clears the set vehicle speed and cancels the cruise control.
·

Malfunction in the FC system.


The dynamic radar cruise control system is disabled until the ignition switch is turned ON again.
- -
If the following condition occurs, the EV control ECU cancels the cruise control while retaining the set vehicle speed in its memory.
·

The millimeter wave radar sensor assembly or the radar sensor cover are dirty.


The dynamic radar cruise control system is prohibited until the condition is corrected.
Radar Cruise
Control
Unavailable
See Owner's Manual
Sounds
If either of the following conditions occurs, the EV control ECU cancels the cruise control while retaining the set vehicle speed in its memory.
·

The measurement becomes extremely unstable due to poor weather conditions.

·

Brake control by the dynamic radar cruise control system is temporarily unavailable.

·

Misalignment of the axis of the millimeter wave radar sensor assembly.

·

A Malfunction in the forward recognition camera.

·

Forward recognition camera temporarily not available.


The dynamic radar cruise control system is prohibited until the condition is corrected.
Radar Cruise
Control
Unavailable
Sounds
If any of the following conditions occur while the vehicle stopped, the EV control ECU cancels the cruise control system.*
·

An open or short circuit in the stop light switch assembly.

·

Malfunction in the millimeter wave radar sensor assembly.

·

Misalignment of the axis of the millimeter wave radar sensor assembly.

·

The brake holding control system is malfunction.

·

The millimeter wave radar sensor assembly or the radar sensor cover are dirty.

·

The measurement becomes extremely unstable due to poor weather conditions.

·

Brake control by the dynamic radar cruise control system is temporarily unavailable.

·

A Malfunction in the forward recognition camera.

·

Forward recognition camera temporarily not available.


Cruise Control Fault
Press Brake to
Deactivate
Visit Your Dealer
Sounds
If the following conditions occur while the vehicle stopped, the EV control ECU cancels the dynamic radar cruise control system.*
·

The vehicle is stopped on a steep hill.


Radar Cruise
Control
Unavailable
Press Brake to
Resume Driving
-
If the following conditions occur while the vehicle stopped, the EV control ECU cancels the dynamic radar cruise control system.*
·

The driver seat belt is unfastened.

·

The driver side door is opened.

·

The vehicle is parked for a long period of time.


- -





FUNCTION


a.

Cruise Control Operation Switch

i.

The operation switches of the dynamic radar cruise control system (cruise control main switch, -SET switch, +RES switch, CANCEL switch and vehicle-to-vehicle distance control switch) are positioned in the steering pad switch assembly.

Component Function

*: Models with RSA

Cruise Control Main Switch
·

Turns the dynamic radar cruise control system on and off.

·

Switches between constant speed control mode and vehicle-to-vehicle distance control mode.


+RES Switch Performs accelerator control, tap-up control, resume control and dynamic radar cruise control with road sign assist*.
-SET Switch Performs set control, coast control, tap-down control and dynamic radar cruise control with road sign assist*.
CANCEL Switch Cancels control.
Vehicle-to-vehicle Distance Control Switch Switches between the vehicle-to-vehicle distance settings.

Y274044C01
2.542,1.521 2.365,0.333 true 5.292,3.146 3.167,2.115 true 5.604,2.5 3.458,1.885 true 3.521,0.698 3.063,1.542 true 5.521,1.625 3.667,1.625 true 2.281,0.156 2.594,0.313 0.313,0.156 10 false *1 5.385,3.135 5.698,3.292 0.313,0.156 10 false *2 5.656,2.479 5.969,2.635 0.313,0.156 10 false *3 5.594,1.552 5.906,1.708 0.313,0.156 10 false *4 3.51,0.542 3.823,0.698 0.313,0.156 10 false *5
*1 Vehicle-to-vehicle Distance Control Switch *2 -SET Switch
*3 CANCEL Switch *4 Cruise Control Main Switch
*5 +RES Switch - -



ii.

Vehicle-to-vehicle Distance Control Switch

·

While the vehicle is being driven in vehicle-to-vehicle distance control mode, the vehicle-to-vehicle distance setting can be changed as follows each time the vehicle-to-vehicle distance control switch is pressed; long → middle → short → long.

·

If the ignition switch is turned off and back ON, the system will default to "long".

·

The vehicle-to-vehicle distance is as follows:

Mode Vehicle-to-vehicle Distance*
Long Approximately 50 m (160 ft.)
Middle Approximately 40 m (131 ft.)
Short Approximately 30 m (98 ft.)

HINT:

*: While driving at a speed of 80 km/h (50 mph).





b.

Dynamic Radar Cruise Control with Road Sign Assist Operation (Models with RSA)

i.

The combination meter assembly customization setting can be used to turn the dynamic radar cruise control with road sign assist on and off.



c.

Curve Speed Reduction Control Function Operation

i.

The combination meter assembly customization setting can be used to switch the curve speed reduction control function between "High", "Low" and "Off".




DIAGNOSIS


a.

In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). For details, refer to the Repair Manual.