FUNCTION OF MAIN COMPONENTS
The main components in the RSA have the following functions.
| Components | Function | |
|---|---|---|
|
*1: The threshold can be adjusted to 1 of 3 levels through the customization function. *2: Models for Europe *3: Models with headup display |
||
| Forward Recognition Camera | ·
Captures road signs. ·
Performs RSA system control based on information of road signs captured. ·
Controls the supply of electric current to the camera heater when the ambient temperature is low. |
|
| Camera Heater (Forward Recognition Hood with Heater Sub-assembly) | Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up. | |
| Millimeter Wave Radar Sensor Assembly | Detects object information and sends a signal to the forward recognition camera. | |
| EV Control ECU | Sends the shift position signal to the forward recognition camera. | |
| No. 2 Skid Control ECU | Sends a vehicle speed signal to the forward recognition camera. | |
| Combination Meter Assembly | - | Sends a turn signal command to the forward recognition camera. |
| Multi-information Display | ·
Displays road signs recognized by the forward recognition camera. ·
The RSA system can be turned on and off through the settings tab. |
|
| Meter Buzzer | Sounds when the speed limit is exceeded*1 or there is an entry prohibition notification. | |
| Airbag ECU (Airbag ECU Assembly) | Yawrate Sensor | Detects the yaw rate and sends it to the forward recognition camera. |
| Steering Sensor | ·
Sends the turning angle of the steering wheel to the forward recognition camera. ·
Sends a turn signal command to the combination meter assembly. |
|
| Turn Signal Switch | Sends a turn signal command to the steering sensor. | |
| Steering Vibration ECU*2 | Vibrates the steering wheel assembly when there is an overtaking notification. | |
| Headup Display (Meter Mirror Sub-assembly)*3 | Displays road signs recognized by the forward recognition camera. | |
| Radio Receiver Assembly*2 | Sends map information from the navigation ECU assembly to the forward recognition camera. | |
| Navigation ECU Assembly*2 | ·
Sends map information to the radio receiver assembly. ·
Performs coordinated control with the forward recognition camera in regards to speed limit information. |
|
| Air Conditioning Amplifier Assembly | Sends the outside temperature signals to the forward recognition camera. | |
| Central Gateway ECU (Network Gateway ECU) | Relays the signal between the CAN communication buses. | |
| Main Body ECU (Multiplex Network Body ECU) | Sends country specification information signals to the forward recognition camera. | |
| DLC3 | ·
The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. ·
The Global TechStream (GTS) can be connected to change settings as desired by the user. |
|
FUNCTION
The RSA system recognizes the following traffic signals using the forward recognition camera.
| Category | Sign Type | Example of Recognizable Sign | |
|---|---|---|---|
| Speed Limit | Round maximum speed limit/End of speed limit |
|
|
| No Overtaking | No overtaking/End of no overtaking |
|
|
| End of Prohibition |
|
||
| Supplemental Signs | Road Condition Signs | Ramp way |
|
| Rain |
|
||
| Wet |
|
||
| Supplemental Signs | Road Condition Signs | Ice |
|
| Time |
|
||
| Information Signs Related Speed Limit | Motorway sign (entrance, exit) |
|
|
| Expressway sign (entrance, exit) |
|
||
| Information Signs Related Speed Limit | Urban area sign (start, end) |
|
|
| Information Signs Related Speed Limit | Residential area sign (start, end) |
|
|
| No Entry |
|
||
| Stop |
|
||
| Category | Sign Type | Example of Recognizable Sign |
|---|---|---|
| Speed Limit | Round maximum speed limit |
|
| Supplemental Sign | School Zone |
|
The RSA system displays the following traffic signals using the forward recognition camera.
| Category | Display Example | Details | |
|---|---|---|---|
| Speed Limit Related |
|
·
Informs the driver of the maximum speed limit of the currently driven road. ·
The displayed sign reflects the speed limit on the recognized sign. |
|
| Speed Limit Related |
|
Informs the driver of motorway signs (entrance, exit). | |
|
Informs the driver of expressway signs (entrance, exit). | ||
| Speed Limit Related |
|
Informs the driver of urban area signs (start, end). | |
| Speed Limit Related |
|
Informs the driver of residential area signs (start, end). | |
| No Overtaking Related |
|
Informs the driver when they are in a no overtaking zone on the currently driven road. | |
| No Entry |
|
Informs the driver that there are vehicle entry restricted sections on the currently driven road. | |
| All Canceled (All restrictions canceled. Return to default road regulations.) |
|
Informs the driver when all applicable prohibitions, such as speed limit and no overtaking, have ended. | |
| Stop |
|
Informs the driver that there is a stop ahead. | |
| Speed Limit with Supplemental Sign Related | Ramp Way |
|
Informs the driver of the ramp way direction. However, this item is not displayed when making a lane change without operating the turn signal light. |
| Rain |
|
Informs the driver of the maximum speed limit on the currently driven road when it is raining or the road surface is wet. | |
| Ice |
|
Informs the driver of the maximum speed limit on the currently driven road when there is accumulated snow or ice. | |
| Speed Limit with Supplemental Sign Related | Time |
|
Informs the driver of the time zone speed limit sign on the currently driven road. |
| Blank |
|
The display is blank when the system is unable to recognize a supplemental sign. | |
A non-official (sign not meeting Vienna Convention) or a recently introduced traffic sign may not be recognized.
| Category | Display Example | Details | |
|---|---|---|---|
| Speed Limit Related |
|
·
Informs the driver of the maximum speed limit of the currently driven road. ·
The displayed sign reflects the speed limit on the recognized sign. |
|
| Conditional Speed Limit Sign | School Zone |
|
Informs the driver that the currently driven road is in a school zone and its speed limit changes depending on the time of day. |
Notification functions are used in the RSA system which invert the colors of displayed signs, flash signs, etc. to notify the driver.
Speed Limit Exceeded Notification
While a speed limit sign is displayed, if the actual vehicle speed exceeds the speed limit plus a designated threshold*1, the colors of the displayed sign are inverted and the buzzer sounds.*2 For example, if the threshold is set to 5 km/h (3 mph) and the speed limit sign is 60 km/h (37 mph), the colors of the displayed sign are inverted and the buzzer sounds, when the actual vehicle speed exceeds 65 km/h (40 mph). Furthermore, the system also inverts a speed limit sign with supplemental sign in the same way. However, the system does not invert the colors of the supplemental sign.
*1: The threshold can be adjusted to 1 of 3 levels through the customization function.
*2: Customization is required for inverted display and sounding of the meter buzzer.
| Notification Method | Display Example |
|---|---|
| Inverted Display |
|
No Overtaking Notification (Models for Europe)
While a no overtaking sign is displayed, if the system detects that the vehicle is attempting to overtake another vehicle, the system flashes the displayed sign and vibrates the steering wheel assembly.*
*: Customization is required for blinking display and steering wheel vibration.
| Notification Method | Display Example |
|---|---|
| Flashing Display |
|
No-entry Notification (Models for Europe)
While a no entry sign is recognized, if the system detects that the driver is driving on a road where entry is prohibited, based on map information, the system flashes the displayed sign and sounds the meter buzzer.*
*: Customization is required for blinking display and sounding of the meter buzzer.
| Notification Method | Display Example |
|---|---|
| Flashing Display |
|
The RSA system can be turned on or off through the settings tab of the multi-information display.
A customization function is used for the RSA, which allows settings such as the notification method and level for exceeding the speed limit to be changed. Setting changes are made through the customization tab of the multi-information display. Refer to the Repair Manual for details.
SYSTEM CONTROL
RSA Control Pattern 1
After a road sign* is recognized by the forward recognition camera, the sign is displayed on the multi-information display.
While a sign is displayed on the multi-information display, if no sign has been recognized within a specified distance, display of the current sign is turned off.
*: Except for stop sign (Models for Europe)
RSA Control Pattern 2
After a stop sign is recognized by the forward recognition camera, the sign is displayed on the multi-information display.
While a sign is displayed on the multi-information display, if the vehicle passes the sign, display of the current sign is turned off.
RSA Control Pattern 3
When the ignition switch is turned off while a speed limit sign is displayed on the multi-information display, the same sign is displayed when the ignition switch is turned ON again.
RSA Control Pattern 4
While a sign is displayed on the multi-information display, the sign is turned off when turning left or right onto a new road.
CONSTRUCTION
Forward Recognition Camera
Road signs captured by the built-in camera are output to the built-in ECU.
The built-in ECU judges road signs recognized by the built-in camera and displays information based on these judgments on the multi-information display and headup display*.
*: Models with headup display
When one of the following operations is conducted, the forward recognition camera angle must be adjusted. For details, refer to the Repair Manual.
The forward recognition camera is removed and reinstalled or replaced.
Parts relating to the tire or suspension are replaced or adjusted.
Strong force is applied onto the forward recognition camera.
DIAGNOSIS
In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). Refer to the Repair Manual for details.