Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM
NM37H0E _54 Brake _097284 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0466235 BRAKE CONTROL SYSTEM CO CONTROL F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  CONTROL  BRAKE HOLD  


SYSTEM CONTROL


a.

When the driver depresses the brake pedal and brings the vehicle to a stop on a level road surface or gentle slope, the brake hold function maintains the wheel cylinder pressure of the 4 wheels, in order to keep the vehicle stationary. As a result, the vehicle will remain stationary even if the driver reduces the pressure on the brake pedal.


b.

While the brake hold function is operating, the No. 2 skid control ECU illuminates the stop lights.


c.

When the driver starts the vehicle off, the system automatically releases the wheel cylinder pressure as the driver depresses the accelerator pedal.

X108881E01
0.177,0.604 0.896,1.885 0.719,1.281 10 false Brake Hold Function Operating 0.177,2.302 1,3.552 0.823,1.25 10 false Brake Hold Function Not Operating 1.333,1.375 3.302,1.708 1.969,0.333 10 false Holds Wheel Cylinder Pressure 3.396,3.104 5.146,3.438 1.75,0.333 10 false Creeps to Start Off

i.

Brake Hold Standby Condition

·

To operate the brake hold, it is first necessary to establish the brake hold standby condition. The brake hold standby condition is established when the driver presses the brake hold switch after all the conditions listed below have been met. As a result, the brake hold standby indicator light illuminates in the combination meter assembly.

Brake Hold Standby Conditions
·

The EV control system, electric parking brake system and electronically controlled brake system are all operating normally.

·

The driver door is closed.

·

The driver seat belt is buckled.





ii.

Brake Hold Operation Condition

·

When all of the conditions listed below are met while the brake hold standby condition is established, the brake hold will operate. When the brake hold operates, the brake hold operated indicator light will illuminate in the combination meter assembly.

Brake Hold Operation Conditions
·

The shift position is in any position other than P or R.

·

The brake pedal is depressed and the vehicle is stopped.

·

The accelerator pedal is not depressed.

·

The vehicle is not on a steep gradient.



HINT:

If the brake hold is inoperative because the vehicle is on a steep gradient, the system informs the driver by turning off the brake hold operated indicator light and outputting a warning message on the multi-information display. To support the start off of the vehicle on a steep uphill gradient, hill-start assist control will operate.




iii.

Brake Hold Operation Ending Condition

·

When one of the conditions listed below has been established, the No. 2 skid control ECU ends the brake hold function. In addition, the No. 2 skid control ECU informs the driver that the brake hold function has ended by turning off the brake hold operated indicator light.

Brake Hold Operation Ending Conditions
·

The accelerator pedal is depressed.

·

The shift position is shifted to P.

·

The shift position is shifted to R while depressing the brake pedal.





iv.

Electric Parking Brake Operation Condition

·

If any one of the conditions listed below is established while the brake hold function is operating and the driver is not depressing the brake pedal, the electric parking brake will lock automatically.

Electric Parking Brake Operation Conditions
·

The driver door is open

·

The driver seat belt is unbuckled.

·

3 minutes have elapsed since the brake hold function operated.



HINT:

After the electric parking brake is locked, make sure to operate the manual function or automatic parking brake release function to release the parking brake before starting off. For details, see the Electric Parking Brake System section.




v.

Brake Hold Standby Condition Canceling Condition

·

If any one of the conditions listed below occurs while the brake hold standby condition is established, the No. 2 skid control ECU cancels the brake hold standby condition.

Brake Hold Standby Condition Canceling Conditions
·

The electric parking brake has locked automatically as a result of the driver seat belt being unbuckled or the driver door being opened.

·

Any one of the following takes place while the vehicle is being driven: the driver seat belt is unbuckled or the driver door is opened.

·

The brake hold switch is pressed while the brake hold function is inoperative.

·

The brake hold switch is pressed while the brake pedal is depressed and the brake hold function is operating.





vi.

Brake Hold Operation Prohibition Condition

·

If any system malfunction listed below occurs, the No. 2 skid control ECU prohibits the operation of the brake hold function. At this time, the No. 2 skid control ECU alerts the driver by flashing the brake hold operated indicator light.

Brake Hold Operation Prohibition Conditions
·

An EV control system malfunction occurs.

·

An electric parking brake system malfunction occurs.

·

An electronically controlled brake system malfunction occurs.*



HINT:

*: When the wheel cylinder pressure cannot be maintained while the brake hold function is operating, the parking brake automatically locks. After the electric parking brake is locked, make sure to operate the manual function or automatic parking brake release function to release the parking brake before starting off. For details, see the Electric Parking Brake System section.