Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM
NM37H0E _54 Brake _097284 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0466235 BRAKE CONTROL SYSTEM GE GENERAL F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

The following brake control functions are provided: Anti-lock Brake System (ABS), Electronic Brake force Distribution (EBD), brake assist, Traction Control (TRC), Vehicle Stability Control (VSC), Active Cornering Assist (ACA), steering cooperative control, hill-start assist control and brake hold.


b.

Vehicle Dynamics Integrated Management (VDIM) is used.


c.

An emergency brake signal system is used. This system reduces the danger of rear-end collisions by automatically flashing the hazard warning lights during emergency braking to warn vehicles to the rear.


d.

A secondary collision brake system is used. This system lessens damage from a secondary collision by controlling the automatic brakes and stop light illumination after a collision occurs.


e.

The No. 2 skid control ECU performs brake control using various driving assistance systems. For details, see each driving assistance system section.



MAIN FEATURES


a.

Electronically Controlled Brake System

i.

The electronically controlled brake system uses sensors to detect the amount of brake pedal depression. Based on this, the No. 1 skid control ECU (brake booster with master cylinder assembly) and No. 2 skid control ECU (brake actuator assembly) calculate the braking force and the brake booster with master cylinder assembly, brake booster with accumulator pump assembly and brake actuator assembly control the brake fluid pressure of the 4 wheels.


ii.

The electronically controlled brake system cooperates with the EV control system to optimally control the brake fluid pressure and regenerative braking. This enhances the efficiency of energy regeneration and improves fuel economy.


iii.

When the system is malfunctioning, brake control continues via the use of non-malfunctioning parts. Also, when the system is not operating, the brake fluid pressure generated in the brake master cylinder by the depression of the brake pedal works as a back-up mechanism to ensure braking force.

X144245E08
0.896,7.063 5.177,7.26 4.281,0.198 10 false : Control Signal Flow 0.865,7.438 4.99,7.635 4.125,0.198 10 false : Brake Fluid Pressure Flow 6.292,7.052 6.906,7.302 0.615,0.25 10 false Wheel 0.177,0.604 1.927,1.135 1.75,0.531 10 false Brake Booster with Accumulator Pump Assembly 0.156,1.24 1.615,1.625 1.458,0.385 10 false - Maintains brake fluid pressure for control 2.396,0.375 3.167,0.573 0.771,0.198 10 false [Input] 2.448,0.146 6.573,0.344 4.125,0.198 10 false Brake Booster with Master Cylinder Assembly 2.417,0.604 4.865,0.802 2.448,0.198 10 false - Generates brake pedal feel 2.406,0.833 5.24,1.021 2.833,0.188 10 false - Detects brake pedal depression amount 2.427,1.083 3.198,1.281 0.771,0.198 10 false [Output] 2.417,1.323 6.094,1.542 3.677,0.219 10 false - Supplies regulated brake fluid pressure to master cylinder 2.427,1.573 4.719,1.771 2.292,0.198 10 false [Brake Fluid Pressure Control] 2.427,1.823 5.938,2.083 3.51,0.26 10 false - Adjusts brake fluid pressure in back of master cylinder 2.417,2.083 4.521,2.281 2.104,0.198 10 false [No. 1 Skid Control ECU] 2.417,2.354 5.24,2.521 2.823,0.167 10 false - Detects brake pedal depression amount 1.5,4.25 4.333,4.448 2.833,0.198 10 false - Detects brake pedal depression amount 2.417,2.635 5.75,2.875 3.333,0.24 10 false - Regulates master cylinder brake fluid pressure 2.417,2.896 6.146,3.271 3.729,0.375 10 false - Drives pump motor of brake booster with accumulator pump assembly 1.479,3.729 5.604,3.927 4.125,0.198 10 false Brake Actuator Assembly 1.51,3.99 2.281,4.188 0.771,0.198 10 false [Input] 1.5,4.521 4.26,4.698 2.76,0.177 10 false [Brake fluid pressure regulation / Output] 1.51,4.792 5.458,5.24 3.948,0.448 10 false - Supplies brake fluid from the master cylinder or reservoir via the pump 1.51,5.25 5.552,5.469 4.042,0.219 10 false - Controls brake fluid pressure of each wheel via solenoid valves 1.51,5.521 3.271,5.719 1.76,0.198 10 false [No. 2 Skid Control ECU] 1.51,5.781 4.25,5.958 2.74,0.177 10 false - Detects brake pedal depression amount 1.51,6.063 5.083,6.51 3.573,0.448 10 false - Controls brake fluid pressure of each wheel during service braking, cooperative braking, ABS, VSC, etc. 1.5,6.563 4.104,6.76 2.604,0.198 10 false - Drives pump and solenoid valves


iv.

Brake control apportions brake force to the hydraulic brake system and regenerative brake system at varying vehicle speeds as follows.

X131270E01
3.323,0.042 5.219,0.573 1.896,0.531 10 false Braking Force Based on Brake Pedal Depression by Driver 1.313,1.688 1.823,2.115 0.51,0.427 10 false Braking Force 1.458,3.26 2.583,3.5 1.125,0.24 10 false Start of Braking 5.094,3.26 6.219,3.5 1.125,0.24 10 false Stop 2.719,3.406 4.875,3.635 2.156,0.229 10 false Example of Cooperative Control 3.635,2.271 5.104,2.646 1.469,0.375 10 true Braking Force by Motor (Energy Regeneration) 2.99,1.271 4.094,1.781 1.104,0.51 10 false Hydraulic Braking Force

X131271E02
2.094,0.573 2.313,0.573 2.313,0.573 2.583,0.948 false 5.542,0.604 5.76,0.604 5.76,0.604 6.031,0.979 false 2,3.948 2.219,3.948 2.219,3.948 2.49,4.323 false 4.667,4.125 5.958,4.365 1.292,0.24 10 false Hydraulic Brake 4.667,4.635 5.958,4.875 1.292,0.24 10 false Motor Brake 0.438,0.708 0.802,0.958 0.365,0.25 10 false High 3.969,0.708 4.333,0.958 0.365,0.25 10 false High 0.438,3.99 0.802,4.24 0.365,0.25 10 false High 0.344,1.26 0.844,1.698 0.5,0.438 10 false Braking Force 3.865,1.219 4.365,1.656 0.5,0.438 10 false Braking Force 0.333,4.594 0.833,5.031 0.5,0.438 10 false Braking Force 1.25,2.219 2.521,2.594 1.271,0.375 10 false Depression Force of Brake Pedal 4.771,2.229 6.042,2.604 1.271,0.375 10 false Depression Force of Brake Pedal 1.292,5.552 2.563,5.927 1.271,0.375 10 false Depression Force of Brake Pedal 2.781,2.292 3.146,2.542 0.365,0.25 10 false High 6.313,2.302 6.677,2.552 0.365,0.25 10 false High 2.781,5.625 3.146,5.875 0.365,0.25 10 false High 1.76,5 3.031,5.375 1.271,0.375 10 false Hydraulic Brake 2.021,1.469 3.292,1.844 1.271,0.375 10 false Hydraulic Brake 5.896,1.26 7.021,1.531 1.125,0.271 10 false Hydraulic Brake 1.219,0.448 2.052,0.938 0.833,0.49 10 false Total Braking Force 4.667,0.51 5.5,1 0.833,0.49 10 false Total Braking Force 1.125,3.854 1.958,4.344 0.833,0.49 10 false Total Braking Force 1.375,3.104 2.646,3.479 1.271,0.375 10 false At high speeds 4.625,3.104 6.188,3.448 1.563,0.344 10 false At mid or low speeds 0.552,6.5 3.74,6.917 3.188,0.417 10 false When shift position is in N or at low speeds 1.229,7.229 6.427,7.531 5.198,0.302 10 false Brake force by hydraulic and regenerative brake system at different vehicle speeds



b.

Vehicle Dynamics Integrated Management (VDIM)

i.

In contrast to the ABS, TRC and VSC functions that were controlled individually in the conventional brake control system, the VDIM manages these functions in the form of an integrated system.


ii.

Furthermore, the VDIM effects cooperative control together with the Electric Power Steering (EPS) system in order to improve the dynamic performance of the vehicle to "run, turn, and stop".

X114080E01
4.531,1.135 5.188,1.135 true 4.729,3.927 5.385,3.927 true 0.125,0.073 6.396,0.271 6.271,0.198 10 false Conceptual Diagram of Control Management: 1.698,0.552 2.875,0.813 1.177,0.26 10 false Cornering 2.979,2.458 4.26,2.708 1.281,0.25 10 false Models with VDIM 1.865,2.021 2.885,2.323 1.021,0.302 10 false Braking 4.875,0.531 6.24,0.802 1.365,0.271 10 false Accelerating 4.865,2.052 6.042,2.313 1.177,0.26 10 false Cornering 5.302,1.063 6.854,1.365 1.552,0.302 10 false Vehicle Control Areas 5.302,1.333 6.99,1.854 1.688,0.521 10 false - All functions are operated seamlessly in unison with each other 5.427,4.135 6.865,4.823 1.438,0.688 10 false - Each function has its own control area and is operated independently 2.896,5.271 4.313,5.521 1.417,0.25 10 false Models without VDIM 1.667,3.094 2.844,3.354 1.177,0.26 10 false Cornering 4.563,4.813 5.74,5.073 1.177,0.26 10 false Cornering 4.875,3.031 6.24,3.302 1.365,0.271 10 false Accelerating 1.719,4.792 2.74,5.094 1.021,0.302 10 false Braking 5.458,3.875 7.01,4.177 1.552,0.302 10 false Vehicle Control Areas




PRECAUTION


a.

ABS

i.

The ABS system cannot increase the performance limit of the tires. Always drive safely and be aware of the vehicle speed and distance to other vehicles.


ii.

Any non-standard components such as non-standard tires that are installed may have a negative effect on the ABS function.


iii.

When braking using ABS, the braking distance may be longer than models without ABS in the following conditions:

·

When driving on a dirt road or a road covered with fresh snow

·

When using tire chains

·

When driving over a joint in the road surface

·

When driving on a rough road such as an unpaved or stone-paved road




b.

Brake Assist

i.

Brake assist cannot increase the performance limit of the fundamental brake system. Always drive safely and be aware of the vehicle speed and distance to other vehicles.



c.

TRC, VSC

i.

The TRC and VSC systems ensure traction and vehicle stability. Do not disable the TRC and VSC functions unless necessary.


ii.

The TRC and VSC systems cannot increase the performance limit of the tires. Always drive the vehicle carefully in conditions in which drive wheel traction or vehicle stability may be lost.



d.

Hill-start Assist Control

i.

Hill-start assist control is not intended to keep the vehicle stationary on a hill for a prolonged period. As hill-start assist control only prevents the vehicle from rolling backwards for 2 seconds after the brake pedal is released, perform start-off within this period.


ii.

When hill-start assist control is operating and the power switch is turned off, hill-start assist control will be canceled without warning.


iii.

Hill-start assist control prevents the vehicle from rolling backwards by controlling the brake force to the 4 wheels. However, the vehicle may not remain stationary when on an extremely steep slope or a low friction surface such as ice.



e.

Brake Hold

i.

The brake hold is not for parking the vehicle for a long period of time in the same way as the parking brake.


ii.

If brake hold control does not operate even when the vehicle stops, depress the brake pedal again firmly to stop the vehicle. If the vehicle still does not stop, confirm the conditions for brake hold control to operate.


iii.

When the power switch is turned off during brake hold operation, control stops.


iv.

This function may not stop the vehicle on steep slopes and slippery roads.



f.

Active Cornering Assist (ACA)

i.

Active Cornering Assist (ACA) cannot increase the performance limit or innate maneuverability of the vehicle itself.


ii.

Do not overly rely on Active Cornering Assist (ACA). Active Cornering Assist (ACA) may not operate effectively when accelerating down slopes or driving on slippery road surfaces.


iii.

When Active Cornering Assist (ACA) frequently operates, Active Cornering Assist (ACA) may temporarily stop operating to ensure proper operation of the brakes, TRC and VSC.