FUNCTION OF MAIN COMPONENTS
| Component | Function | ||
|---|---|---|---|
| Brake Booster with Master Cylinder Assembly | No. 1 Skid Control ECU | ECU Portion | Calculates the optimal brake force based on the brake pedal stroke and No. 2 skid control ECU commands and sends signals to the brake actuator. |
| Solenoid Relay | Supplies power to the solenoid valves. | ||
| Motor Relay | Supplies power to the pump motor. | ||
| Brake Actuator | Accumulator Pressure Sensor (Pacc) | Detects the accumulator brake fluid pressure and is used to control the pump motor. | |
| Stroke Simulator Pressure Sensor (Prct) | Detects the brake fluid pressure in the stroke simulator which is generated by the depression of the brake pedal by the driver. | ||
| Servo Pressure Sensor (Psrv) | Detects the fluid pressure of the servo chamber. | ||
| Gap Hold Valve (SGH) | ·
During normal control, transmits the brake fluid pressure generated by the depression of the brake pedal by the driver to the stroke simulator. ·
During a malfunction, isolates the brake fluid pressure of the gap hold chamber. |
||
| Stroke Simulator Cut Valve (SSA) | Allows the stroke simulator pressure to flow to the brake master cylinder reservoir assembly such as when the system is malfunctioning. | ||
| Linear Solenoid Valve (SLA, SLR) | Based on commands from the No. 1 skid control ECU, outputs regulated brake fluid pressure. | ||
| Stroke Simulator | Generates a natural brake pedal feel in response to depression of the brake pedal by the driver. | ||
| Relief Valve | Opens to prevent excess pressure created by the pump motor. | ||
| Regulator | ·
Supplies pressurized brake fluid which is controlled by the linear solenoid valves to the servo chamber when the No. 1 skid control ECU is operating. ·
Supplies brake fluid pressure from the accumulator to the servo chamber when the No. 1 skid control ECU is not operating or during back-up when the No. 1 skid control ECU is malfunctioning. |
||
| Master Cylinder | Generates brake fluid pressure in accordance with the depression amount of the brake pedal. | ||
| Brake Master Cylinder Reservoir Assembly | Brake Fluid Level Warning Switch | Detects when the brake fluid level is low. | |
| Brake Booster with Accumulator Pump Assembly | Pump Motor | Pumps the brake fluid from the brake master cylinder reservoir assembly to the accumulator. | |
| Accumulator | Accumulates brake fluid supplied by the pump motor under pressure. | ||
| Brake Actuator Assembly | No. 2 Skid Control ECU | ECU Portion | ·
Determines the condition of the vehicle based on signals from each sensor, and sends control signals to the No. 1 skid control ECU and brake actuator. ·
Performs regenerative cooperative braking by communicating with each ECU. |
| Solenoid Relay | Supplies power to the solenoid valves. | ||
| Motor Relay | Supplies power to the pump. | ||
| Brake Actuator | Pump | Pumps brake fluid from the master cylinder or brake fluid reservoir. | |
| Linear Solenoid Valve (SM1, SM2) | Regulates brake fluid pressure supplied from the pump. | ||
| Pressure Holding Solenoid Valve, Pressure Reduction Solenoid Valve | Independently controls the brake fluid pressure of the 4 wheels when ABS, TRC, VSC, etc. is operating. | ||
| Master Cylinder Pressure Sensor (Pmc) | Built into the brake actuator and detects the master cylinder pressure. | ||
| Wheel Cylinder Pressure Sensor (Pwc) | Detects the brake fluid pressure in the wheel cylinder. | ||
| Speed Sensor | Detect the wheel speed of each of the 4 wheels. | ||
| Airbag ECU (Airbag ECU Assembly) | ECU Portion | ·
Sends the collision detection signal to the No. 2 skid control ECU. ·
Sends the driver side seat belt fasten condition signal to the main body ECU. |
|
| Yawrate Sensor | Detects the vehicle's yaw rate. | ||
| Deceleration Sensor | Detects the vehicle's longitudinal and lateral deceleration. | ||
| Steering Sensor | Detects the direction and angle of the steering wheel. | ||
| Stop Light Switch Assembly | Detects the brake pedal depressing signal. | ||
| VSC OFF Switch | Enables the driver to select "Normal Mode", "TRC OFF Mode" or "VSC OFF Mode". | ||
| Brake Hold Switch | Switches the brake hold on and off. | ||
| Brake Pedal Stroke Sensor Assembly | Directly detects the extent of the brake pedal stroke operated by the driver. | ||
| Front Door Courtesy Light Switch Assembly (for Driver Door) | Detects whether the door is open or closed and sends the information to the No. 1 skid control ECU. | ||
| EV Control ECU | ·
Controls the brake force of regenerative braking during regenerative brake cooperative control according to communication with the No. 2 skid control ECU. ·
Controls the motive force when TRC and VSC are operating according to communication with the No. 2 skid control ECU. ·
Sends the accelerator pedal position signal, shift position signal and brake request signal to the No. 2 skid control ECU. |
||
| Inverter with Converter Assembly | MG ECU | Sends information regarding the motor to the No. 2 skid control ECU during regenerative cooperative braking. | |
| Power Steering ECU with Motor Assembly | Power Steering ECU | Controls the steering assist torque based on the signals received from the No. 2 skid control ECU. | |
| Main Body ECU (Multiplex Network Body ECU) | ·
Detects whether the door is open or closed and sends the information to the No. 2 skid control ECU. ·
Sends the driver side seat belt fasten condition signal to the No. 2 skid control ECU. |
||
| Hazard Warning Signal Switch Assembly | Switches the Hazard Warning Signal on and off. | ||
| Combination Meter Assembly | Brake System Warning Light (Red Indicator) | ·
Illuminates to warn the driver when a malfunction that may affect braking performance is detected in the brake system. ·
Illuminates to warn the driver when the No. 1 skid control ECU or the No. 2 skid control ECU detects a malfunction in the ABS system or EBD function (the ABS warning light illuminates simultaneously). ·
Illuminates to warn the driver when the brake fluid level is low. |
|
| Brake System Warning Light (Yellow Indicator) | ·
Illuminates to inform the driver when a minor malfunction that will not interfere with the brake control system is detected. ·
Illuminates to inform the driver that the No. 2 skid control ECU detected a malfunction in the electric parking brake system. |
||
| ABS Warning Light | Illuminates to warn the driver when the No. 1 skid control ECU or the No. 2 skid control ECU detects a malfunction in the ABS system or brake assist function. | ||
| Slip Indicator Light | ·
Blinks to inform the driver when the VSC, TRC or ABS system is operating. ·
Illuminates to warn the driver when the No. 2 skid control ECU detects a malfunction in the VSC or TRC system. |
||
| Brake Hold Standby Indicator Light | Illuminates to inform the driver that the brake hold standby condition has been established. | ||
| Brake Hold Operated Indicator Light | ·
Illuminates to inform the driver that the brake hold function is operating. ·
Blinks to alert the driver when the No. 2 skid control ECU detects a malfunction in the brake hold function. |
||
| VSC OFF Indicator Light | Illuminates to inform the driver when VSC OFF mode is selected. | ||
| Multi-information Display | ·
Displays the information message when TRC OFF mode is selected. ·
Displays a warning message when a malfunction is detected in the brake control system. |
||
| Buzzer | Sounds together with a message display on the multi-information display during a system malfunction. | ||
FAIL-SAFE
If a malfunction is detected in the brake system, the fail-safe function operates. Depending on the type of malfunction, the fail-safe function informs the driver via warning indicators in the combination meter assembly and continues brake control via the use of non-malfunctioning parts. Also, when the system is not operating, the fluid pressure generated in the brake master cylinder by the depression of the brake pedal works as a back-up mechanism to ensure braking force.
DIAGNOSIS
A diagnosis function is provided in consideration of serviceability in order to simplify the inspection of systems. For details of the diagnosis function, refer to Repair Manual.