FUNCTION OF MAIN COMPONENTS
| Component | Function |
|---|---|
| Blind Spot Monitor Sensor LH | Sounds the RCTA buzzer when a pedestrian detection signal is received from the rear television camera assembly. |
| Blind Spot Monitor Sensor RH | Sends pedestrian detection signals from the rear television camera assembly to the blind spot monitor sensor LH. |
| Rear Television Camera Assembly | Detects pedestrians behind the vehicle and sends a pedestrian detection display signal to the parking assist ECU. |
| RCTA Buzzer (Blind Spot Monitor Buzzer) | Sounds an alarm to notify the driver when a pedestrian is detected behind the vehicle. |
| Multi-display Assembly | Displays detection information to notify the driver when a pedestrian is detected behind the vehicle. |
| Combination Meter Assembly
·
RCD OFF Indicator ·
Multi-information Display |
·
Sends a RCD on/off signal to the rear television camera assembly. ·
Illuminates the RCD OFF indicator when RCD is off. ·
When a malfunction is detected in the rear television camera assembly or the rear television camera assembly determines that control is not possible, the RCD OFF Indicator blinks and a message is displayed on the multi-information display to warn the driver. ·
Sends customization information to the rear television camera assembly. |
| Parking Assist ECU | Receives pedestrian detection signals from the rear television camera assembly and outputs a video signal to the multi-display assembly |
| Steering Sensor | Sends a steering angle signal to the rear television camera assembly. |
| EV Control ECU | Sends a shift position signal to the rear television camera assembly. |
| No. 2 Semiconductor Power Integration ECU | Sends the shift position R signal to the parking assist ECU. |
| Brake Actuator Assembly
·
No. 2 Skid Control ECU |
Sends a vehicle speed signal to the rear television camera assembly. |
| Central Gateway ECU (Network Gateway ECU) | Relays the signal between the CAN communication buses. |
| DLC3 | ·
The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. ·
The Global TechStream (GTS) can be connected to change settings as desired by the user. |
OPERATING CONDITION
RCD operates when all of the following conditions are established.
·
Power source mode is turned on (IG). ·
RCD is on. ·
The shift position is R. |
SYSTEM CONTROL
If a pedestrian is in the area behind the vehicle or if the rear television camera assembly detects that a pedestrian is approaching the vehicle from behind, the system urges caution from the driver by sounding the RCTA buzzer and displaying information on the multi-display assembly, as shown below.
| Area | Warning | |
|---|---|---|
| Buzzer | Icon Display on Multi-display | |
| A | Sounds repeatedly. | Blinks 3 times then stays illuminated. |
| B | When own vehicle is stopped: Sounds 3 times. | Blinks 3 times then stays illuminated. |
| When own vehicle is moving: Sounds repeatedly. | ||
| C | If own vehicle and pedestrian approach area A within a certain amount of time: Sounds repeatedly. | If own vehicle and pedestrian approach area A within a certain amount of time: Sounds 3 times, then stays illuminated. |
If a pedestrian is detected in warning area A, a repeating alarm sounds, and then the icon blinks 3 times and stays illuminated to warn the driver.
If a pedestrian is detected in warning area B and the driver's own vehicle is stopped, the buzzer sounds 3 times and then the icon blinks 3 times and stays illuminated to warn the driver.
If a pedestrian is detected in warning area C or if the driver's own vehicle and the pedestrian approach area A within a certain amount of time, the buzzer sounds repeatedly, and then the icon blinks 3 times and stays illuminated to warn the driver.
FUNCTION
RCD Operation
The combination meter assembly customization setting can be used to turn RCD on and off.
A RCD OFF indicator is located in the combination meter assembly to make it possible to check whether RCD is on or off. When the RCD is off, the indicator light illuminates to indicate the operation status.
The combination meter assembly customization setting can be used to change the volume of the buzzer.
Buzzer Sound Temporary Mute Function
When the buzzer is sounding, the warning buzzer can be temporarily muted by operating the steering pad switch assembly.
Then, If the shift position is changed to R, the temporary mute function is automatically canceled.
Customization Function
Settings of some functions can be changed as desired by the user. Refer to the Repair Manual for details.
DIAGNOSIS
In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the GTS. Refer to the Repair Manual for details.