Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF SUNSHADE SYSTEM
NM37H0E _58 Vehicle Interior _097722 INTERIOR PANELS / TRIM _0466353 ROOF SUNSHADE SYSTEM CO CONTROL F

INTERIOR PANELS / TRIM  ROOF SUNSHADE SYSTEM  CONTROL  ROOF SUNSHADE CONTROL  


SYSTEM CONTROL


a.

Recognition of Sunshade Trim Position

i.

Based on the pulse signals input from Hall IC1 and Hall IC2, the roof sunshade ECU (sliding roof drive gear sub-assembly) recognizes the sunshade trim sub-assembly position as shown in the illustration below with the mechanical lock position of the sunshade trim sub-assembly as the starting position. Motor control is performed by comparing this position information to the operation signals from the roof sunshade switch.

Y127074C01
5.948,1.531 6.313,1.729 0.365,0.198 10 false k 3.792,1.521 4.406,1.719 0.615,0.198 10 false j 1.198,1.51 1.656,1.708 0.458,0.198 10 false a 4.896,3 5.813,3.198 0.917,0.198 10 false p 3.458,3 4.375,3.198 0.917,0.198 10 false o 3.792,1.781 4.802,1.948 1.01,0.167 10 false l 4.719,2.521 5.99,2.781 1.271,0.26 10 false n 3.76,2.271 4.969,2.5 1.208,0.229 10 false m 6.469,0.698 7.156,0.969 0.688,0.271 10 false g 5.969,1.021 6.469,1.302 0.5,0.281 10 false i 2.198,0.688 4.125,0.865 1.927,0.177 10 false f 1.656,2.021 7.156,2.521 5.5,0.5 10 false e 1.656,1.781 7.156,1.969 5.5,0.188 10 false d 0.74,2.375 1.354,2.698 0.615,0.323 10 false c 0.74,1.885 1.323,2.219 0.583,0.333 10 false b 2.698,1.031 3.375,1.229 0.677,0.198 10 false h 1.656,2.271 7.156,2.458 5.5,0.188 10 false d 1.656,2.5 7.156,3 5.5,0.5 10 false e 4.74,2.01 5.75,2.177 1.01,0.167 10 false l
*a Area Name *b Operation Permission Area
*c Operation Startable Area *d Close Operation
*e Open Operation *f Fully Open Slide Mechanical Stop (Origin)
*g Fully Closed Slide Mechanical Stop (Origin) *h Slide Fully Open Position
*i Slide Fully Closed Position *j Slide Area
*k Fully Closed Area *l Auto Operation Permitted Area
*m Slide Close Startable Area *n Slide Open Startable Area
*o Open Direction *p Close Direction



ii.

Necessity of sunshade trim position initialization

1.

In the roof sunshade system, the pulse sensor electrically reads the information indicating the current position of the sunshade trim sub-assembly from the rotation of the motor, and various functions are controlled based on this position information.

2.

The position information of the sunshade trim sub-assembly is stored in EEPROM (nonvolatile memory) of the sliding roof drive gear sub-assembly. Therefore, although the position information is not lost if the battery or connector is disconnected and reconnected, when the sliding roof drive gear sub-assembly is replaced, the initialization operation must be performed to make the system "learn" the position of the sunshade trim sub-assembly.


NOTICE:

If the system has not "learned" the current position of the sunshade trim sub-assembly, some functions, such as the jam protection function, will not operate.


Precaution for when the position of the sunshade trim sub-assembly has not been "learned"
The jam protection mechanism does not operate. (If a foreign object is jammed between the sunshade trim sub-assembly and roof opening, and a load of a certain value or higher is applied, the sunshade trim sub-assembly stops but the reverse operation is not performed.)
The one-touch auto open-and-close function does not operate.
The sunshade trim sub-assembly can be operated while pressing the roof sunshade switch.

Initialization operation
With the power switch on (IG), continuously press the open side of the roof sunshade switch and slide the sunshade trim sub-assembly until it fully opens and stops*. The position after the sunshade trim sub-assembly has fully slid is stored as the reference position (starting position 0). If the subsequent operation stops at the proper fully open position, then "learning" is completed.
If there is an excessive load on the sunshade trim sub-assembly during the initialization operation, and approximately 20 seconds or more elapse before reaching the fully open position, or an abnormality occurs in the sensor that detects the number of motor rotations, then the position of the sunshade trim sub-assembly cannot be "learned".
After the initialization operation, be sure to perform an operation check of the roof sunshade system. Refer to the Repair Manual for details of the operation check.

HINT:

*: If the fail-safe mode is entered due to an overload stop during the slide close operation, the motor operation will stop partway through the open operation during initialization. Therefore, after the operation stops, the switch must be operated again to perform the slide operation to the fully open position.




b.

One-touch Auto Open Operation

i.

When OPEN switch ON is input for approximately 0.3 seconds or more to the roof sunshade ECU, rotate the roof sunshade motor in the open direction. (*a in illustration)


ii.

The roof sunshade ECU counts the pulse signals from the Hall IC, and when it detects from the number of rotations of the roof sunshade motor that the sunshade trim sub-assembly has reached the fully open position, stop the roof sunshade motor. Also, when an ON input of the OPEN and CLOSE switch occurs during the automatic operation, roof sunshade motor is turned OFF in the same manner.

Y268407C01
4.542,1.656 4.542,0.406 4.542,0.406 4.708,0.406 true 0.469,2.938 0.604,2.938 0.604,2.938 1.469,2.563 true 3.323,1.25 3.323,0.417 3.323,0.417 3.49,0.417 true 4.021,3.781 4.021,4.344 4.021,4.344 4.188,4.344 true 4.75,0.344 5.063,0.5 0.313,0.156 10 false *1 3.521,0.354 3.854,0.51 0.333,0.156 10 false *2 0.302,2.854 0.615,3.01 0.313,0.156 10 false *3 1.656,2.406 1.969,2.563 0.313,0.156 10 false *a 0.177,2.427 0.49,2.583 0.313,0.156 10 false *b 4.219,4.281 4.531,4.438 0.313,0.156 10 false *2
*1 Sunshade Trim Sub-assembly *2 Drive Belt
*3 Roof Sunshade Motor
·

Drive Gear


- -
*a Drive Gear Rotation Direction (Open Operation) *b Front




c.

One-touch Auto Close Operation

i.

When CLOSE switch ON is input for approximately 0.3 seconds or more to the roof sunshade ECU, rotate the roof sunshade motor in the close direction. (*a in illustration)


ii.

The roof sunshade ECU counts the pulse signals from the Hall IC, and when it detects from the number of rotations of the roof sunshade motor that the sunshade trim assembly has reached the fully closed position, stop the roof sunshade motor. Also, when an ON input of the OPEN and CLOSE switch occurs during the automatic operation, roof sunshade motor is turned OFF in the same manner.

Y268408C01
0.458,3.042 0.625,3.042 0.625,3.042 1.49,2.573 true 5.885,0.438 5.719,0.438 5.719,0.438 5.719,1.521 true 4,0.417 3.833,0.417 3.833,0.417 3.833,1.219 true 4,4.417 3.833,4.417 3.833,4.417 3.833,3.854 true 5.927,0.365 6.24,0.521 0.313,0.156 10 false *1 4.031,0.354 4.344,0.51 0.313,0.156 10 false *2 0.302,2.958 0.615,3.115 0.313,0.156 10 false *3 1.677,2.594 1.99,2.75 0.313,0.156 10 false *a 0.177,2.417 0.49,2.573 0.313,0.156 10 false *b 4.042,4.365 4.354,4.521 0.313,0.156 10 false *2
*1 Sunshade Trim Sub-assembly *2 Drive Belt
*3 Roof Sunshade Motor
·

Drive Gear


- -
*a Drive Gear Rotation Direction (Close Operation) *b Front




d.

Roof Sunshade Jam Protection Mechanism Operation

i.

When the roof sunshade ECU detects changes in the pulse signals from the Hall IC (when it detects that the roof sunshade motor rotation speed has slowed down or motor lock has occurred) during the automatic close operation (except during manual control due to a switch operation), the sunshade trim sub-assembly judges that a foreign object is jammed, which reverses the rotation of the sliding roof sunshade motor.


ii.

When the roof sunshade ECU detects the position approximately 218 mm in the reverse direction or detects the fully open position from the pulse signals of the Hall IC, it turns OFF the relay to stop the roof sunshade motor.




FAIL-SAFE


a.

Fail-safe for Roof Sunshade Motor Operation

i.

When the elapsed time of the motor operation (relay ON time) by the roof sunshade ECU reaches approximately 20 seconds, the turns OFF automatically to protect the roof sunshade motor and circuit. (Continuous operation limit function)


ii.

In the event that a problem occurs where the sunshade trim sub-assembly cannot fully close (does not stop in the fully closed position) due to an abnormality of the jam protection mechanism, the system can be forcibly transitioned to the position information non-learned control status by pressing the "CLOSE" side of the roof sunshade switch continuously for approximately 10 seconds or more. Then, the position information can be corrected by performing the initialization operation. (When the roof sunshade switch is pressed continuously, the learning operation starts immediately after transitioning to the non-learned status. Therefore, keep operating the switch until the sunshade trim sub-assembly is fully closed.)