Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
NM37H0E _58 Vehicle Interior _097853 HEATING / AIR CONDITIONING _0466362 AIR CONDITIONING SYSTEM DE DETAILS F

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  DETAILS  COOLER COMPRESSOR  


CONSTRUCTION


a.

ESB27 Type Compressor

i.

An ESB27 type compressor with motor assembly that is driven by a motor is used. The basic construction and operation of this compressor are the same as an ordinary scroll compressor, except that it is driven by an electric motor.

ESB27 Type Compressor
Y268341


ii.

The compressor with motor assembly consists of a spirally wound fixed scroll and rotating scroll that form a pair, an injection block, a brushless motor, an oil separator, a motor shaft and an air conditioning inverter.


iii.

An air conditioning inverter is integrated with the compressor with motor assembly. This inverter operates the compressor on EV battery voltage.


iv.

The fixed scroll is integrated with the housing. Because the rotation of the shaft causes the rotating scroll to revolve while maintaining the same posture, the volume of the space that is partitioned by both scrolls varies to perform the suction, compression and discharge of the refrigerant gas. Locating the suction port directly above the scrolls enables direct suction, achieving improved suction efficiency. Containing a built-in oil separator, the compressor is able to separate the compressor oil that is intermixed with the refrigerant and circulates in the refrigerant cycle, achieving reduction in the oil circulation rate.


v.

Low-moisture permeation hoses are used for the suction and discharge hoses of the compressor in order to minimize the entry of moisture into the refrigerant cycle.


vi.

A thrust valve mechanism is used as a back pressure adjustment method, which enables appropriate adjustment of back pressure to reduce excessive pressure and improve efficiency.

Y268342C01
1.417,1 2.333,1 true 1.417,1.906 1.583,1.906 1.583,1.906 2.865,1.302 true 1.677,2.344 1.844,2.344 1.844,2.344 3.01,1.375 true 1.583,0.333 1.75,0.333 1.75,0.333 2.885,1.021 true 3.135,0.823 3.135,0.156 3.135,0.156 2.99,0.156 true 5.25,4.333 5.083,4.333 5.083,4.333 4.5,3.75 true 3.833,1.25 4.25,0.167 4.25,0.167 4.417,0.167 true 3.833,1.583 3.833,2.5 3.833,2.5 4,2.5 true 2.813,0.094 3.125,0.25 0.313,0.156 10 false *1 1.385,0.26 1.698,0.417 0.313,0.156 10 false *2 1.25,0.938 1.563,1.094 0.313,0.156 10 false *3 1.219,1.854 1.531,2.01 0.313,0.156 10 false *4 1.479,2.292 1.792,2.448 0.313,0.156 10 false *5 4.052,2.448 4.365,2.604 0.313,0.156 10 false *6 4.469,0.115 4.781,0.271 0.313,0.156 10 false *7 5.292,4.26 5.604,4.417 0.313,0.156 10 false *8
*1 Rotating Scroll *2 Fixed Scroll
*3 Oil Separator *4 Discharge Port
*5 Thrust Valve *6 Brushless Motor
*7 Motor Shaft *8 Air Conditioning Inverter


CAUTION:

In order to ensure the proper insulation of the internal high-voltage portion of the compressor with motor assembly and the compressor housing, this model has used a compressor oil (ND11) with a high level of insulation performance. Therefore, never use a compressor oil other than ND11 type compressor oil or its equivalent.





OPERATION


a.

ESB27 Type Compressor

i.

The compressor with motor assembly performs suction, compression and discharge of refrigerant gas as described in the table below.

Stroke Operation
Suction As the capacity of the compression chamber, which is created between the rotating scroll and the fixed scroll, increases in accordance with the revolution of the rotating scroll, refrigerant gas is drawn in from the intake port.
Compression As the movable scroll orbits eccentrically, the volume of the high-pressure chamber decreases. With this, the pulled in refrigerant is steadily compressed and discharged into the center of the fixed scroll. Partway through the compression process, partially compressed refrigerant is injected. As the movable scroll orbits eccentrically, the gas injection port is isolated from the compression chamber and the flow of injected refrigerant stops. The compression of the refrigerant is complete after the movable scroll completes 2 orbits.
Discharge When the compression of the refrigerant gas is completed and the refrigerant pressure becomes high, the refrigerant gas discharges through the discharge port located in the center of the fixed scroll by pushing the discharge valve.

Y210298E02
0.885,0.844 1.073,0.844 1.073,0.844 1.646,1.417 true 3.115,2.396 2.875,2.396 2.875,2.396 2.177,1.573 true 3.156,2.885 2.792,2.885 2.792,2.885 1.667,1.521 true 2.396,0.167 2.885,0.406 0.49,0.24 10 false Suction 6.292,3.531 7.125,3.781 0.833,0.25 10 false Compression 0.344,4.813 0.99,5.063 0.646,0.25 10 false Discharge 0.24,0.74 0.896,1.135 0.656,0.396 10 false Discharge Port 3.167,2.313 4.313,2.625 1.146,0.313 10 false Rotating Scroll 3.198,2.781 4.344,3.094 1.146,0.313 10 false Fixed Scroll


ii.

Thrust Valve Mechanism Operation

1.

If the back pressure is less than the value required, pressure is supplied from the compression room to the back pressure room using the thrust valve installed in the rotating scroll to adjust the back pressure to the appropriate value.

Y210299E02
4.156,0.24 3.896,0.24 3.896,0.24 3.49,1.135 true 1.458,1.281 1.688,0.281 1.688,0.281 3.073,1.354 true 2.802,1.75 2.469,2.375 2.469,2.375 2.135,2.375 true 5.802,1.25 5.99,0.271 5.99,0.271 6.135,0.271 true 2.99,0.115 3.375,0.115 3.375,0.115 3.156,1.125 true 4.458,0.563 4.094,0.563 4.094,0.563 3.844,1.104 true 0.125,0.177 1.667,0.552 1.542,0.375 10 false Thrust Valve Mechanism 2.667,2.25 4.323,2.552 1.656,0.302 10 false Back Pressure Sufficient 1.365,2.292 2.302,2.531 0.938,0.24 10 false Fixed Scroll 6.167,0.167 7.083,0.635 0.917,0.469 10 false Supply of Back Pressure 4.198,0.146 5.573,0.344 1.375,0.198 10 false Rotating Scroll 4.49,0.49 5.99,0.708 1.5,0.219 10 false Back Pressure Room 2.125,0.031 2.969,0.365 0.844,0.333 10 false Compression Room 4.885,2.26 6.542,2.458 1.656,0.198 10 false Back Pressure Insufficient