FUNCTION
FC System Indicator
An FC system indicator is installed in the multi-information display.
Speed Meter
An vehicle speed is installed in the main display.
Fuel Gauge
An fuel gauge is installed in the main display.
Shift Position Indicator
An shift position indicator is installed in the main display.
ODO/TRIP Meter
An ODO/TRIP meter is installed to the main display.
The trip switch is used to change display items.
| Display Range | 0 to 999999 km |
| Function | Displays 999999 km when there is a display overflow. |
| Display Range | 0.0 to 9999.9 km |
| Function | When there is a display overflow, the display returns to 0.0 km from 9999.9 km and the total continues. |
Outside Temperature Gauge
An outside temperature gauge is installed in the main display.
| Display Range | -40 to 50 °C (-40 to 122°F) |
| Function | ·
A signal from the air conditioning amplifier assembly is processed and the outside air temperature is displayed. ·
The displayed value is updated approximately every second. |
Clock
An current time is installed in the main display.
Rheostat
A rheostat function which can be used to control the brightness of the meter panel is installed.
Brightness can be adjusted in 22 levels, and the adjustment range changes based on whether it is determined to be day or night.
Brightness adjustment is performed using the rheostat switch.
Warning lights and indicator lights
Warning indicators are provided in the combination meter, and illuminate or blink to show the status of each system.
LEDs (Light Emitting Diodes) are used in warning indicator lights to save energy and increase the lifespan.
| Item | Name | Color | Outline |
|---|---|---|---|
|
*: This illustration is an example only. |
|||
|
Turn Signal Indicator Light | Green | Flashes when the turn signal switch or hazard warning signal switch assembly is ON. |
|
BSM OFF Indicator | Amber | ·
Illuminates for approximately 3 seconds to perform an indicator check when the power switch is turned on (IG) during normal operation of the blind spot monitor system. ·
Illuminates when the blind spot monitor system is set to OFF. ·
Illuminates when a blind spot monitor system malfunction occurs. |
|
Hydrogen Leak Warning Light | Red | ·
Illuminates for approximately 3 seconds when the power switch is turned on (IG). ·
Illuminates when the hydrogen concentration is at or above the threshold (approximately 3.0%). |
|
Toyota Parking Assist Sensor OFF Indicator | Amber | ·
Illuminates when the Toyota parking assist sensor system is OFF. ·
Illuminates when an Toyota parking assist sensor system malfunction occurs. |
|
Slip Indicator Light | Amber | ·
Illuminates for approximately 3 seconds when the TRC and VSC systems are operating normally and the power switch is turned on (IG). ·
Flashes when the TRC or VSC system is operating. ·
Illuminates when the TRC or VSC system is malfunctioning. ·
Illuminates when there is a communication malfunction with the No. 2 skid control ECU. |
|
RCTA OFF Indicator Light | Amber | ·
Illuminates when the RCTA function is set to OFF. ·
Illuminates when the RCTA is malfunctioning. |
|
Rear Fog Light Indicator | Amber | Illuminates when the rear fog lights are illuminated. |
|
Driver/Front Passenger Seat Belt Warning Light | Red | ·
Illuminates/flashes when the driver seat or passenger seat seatbelt is unfastened and the power switch is turned on (IG). ·
Blinks when the vehicle speed is 20 km/h (12.4 mph) or higher with the seat belt not fastened, or whenever the vehicle is not parked (when the shift position is not in P or the parking brake is not applied at a vehicle speed of 1.75 km/h (1.1 mph) or higher) with the seat belt not fastened. ·
Illuminates after blinking for a certain period of time. |
|
VSC OFF Indicator Light | Amber | ·
Illuminates for approximately 3 seconds when the VSC systems are operating normally and the power switch is turned on (IG). ·
Illuminates when the VSC system is set to OFF. ·
The status is retained until the power switch is turned off when there is a communication malfunction with the No. 2 skid control ECU. |
|
Tail Light Indicator Light | Green | Illuminates when the tail lights are illuminated. |
|
SRS Warning Light | Red | ·
Illuminates for approximately 6 seconds when the airbag system is operating normally and the power switch is turned on (IG). ·
Turns on to alert the driver when the airbag sensor assembly detects a malfunction in the airbag system. ·
Illuminates after the airbag system deploys. |
|
READY Indicator Light | Green | ·
Blinks when the vehicle switches to a status where it can be driven during the FC system check, or when charging the EV battery. ·
Illuminates when the FC system is operating. |
|
Headlight High Beam Indicator Light | Blue | Illuminates when the high beams are illuminated. |
|
Automatic High Beam Indicator | Green | Illuminates when the automatic high beam system is operating. |
* |
Road Sign Icons | - | The applicable road sign icon illuminates when the RSA system recognizes a road sign. |
|
Cruise SET Indicator | Green | Illuminates when the set vehicle speed of the dynamic radar cruise control system is set. |
|
Cruise Control Indicator (Constant Speed Control Mode) | Green | ·
Illuminates when the dynamic radar cruise control system (constant speed control mode) is ON. ·
Does not illuminate when a malfunction occurs in the dynamic radar cruise control system even when the system is ON. |
|
Cruise Control Indicator (Vehicle-to-vehicle Distance Control Mode) | Green | ·
Illuminates when the dynamic radar cruise control system (vehicle-to-vehicle distance control mode) is ON. ·
Does not illuminate when a malfunction occurs in the dynamic radar cruise control system even when the system is ON. |
|
Lane Tracing Assist System Indicator | White | Illuminates when the lane tracing assist system is ON. |
| Green | Illuminates when lane tracing assist system is operating (steering assist is being performed). | ||
| Amber | ·
Illuminates when a malfunction occurs in the lane tracing assist system. ·
Flashes when a lane tracing assist warning is being output. |
||
|
Br Mode Indicator | Green | Illuminates when Br mode is selected. |
|
Ice Warning | White | ·
Illuminates when the outside air temperature is 3 °C (37.4 °F) or less to warn the driver that the road surface may be icy. ·
After illuminating, turns off when the outside air temperature is 5 °C (41 °F) or more. |
|
SNOW Mode Indicator | Amber | Illuminates when SNOW mode is selected. |
|
ECO Mode Indicator | Green | Illuminates when ECO mode is selected. |
|
SPORT Mode Indicator | Green | Illuminates when SPORT mode is selected. |
|
RCD OFF Indicator | Amber | ·
Illuminates when the PKSA system RCD is off. ·
Blinks when an RCD malfunction occurs. |
|
Coolant Warning | Blue | Illuminates when the coolant temperature is approximately 0 °C (32 °F) or less. |
| Red | Illuminates when the coolant temperature is approximately 100 °C (212 °F) or high. | ||
|
Blower Indicator | White | Illuminates when air conditioning system is operated. |
|
Low Fuel Level Warning Light | Amber | Illuminates when the hydrogen level is at or below the threshold (hydrogen tank level approximately 17% ). |
|
Rear Passenger Seat Belt Warning Light | Red | Illuminates/blinks depending on the whether rear seat belts are fastened. |
|
|||
|
Parking Brake Warning Light | Red | ·
Illuminates when the electric parking brake is operating. ·
Flashes when the electric parking brake system cannot operate when the electric parking brake switch is operated. |
|
ABS Warning Light | Amber | ·
Illuminates for approximately 3 seconds when the brake control system is operating normally and the power switch is turned on (IG). ·
Illuminates when a malfunction occurs that prevents the ABS system from operating. ·
Illuminates when there is a communication malfunction with the No. 2 skid control ECU. |
|
Popup Hood Warning Light | Red | ·
Illuminates for approximately 6 seconds when the pedestrian protection system is operating normally and the power switch is turned on (IG). ·
Turns on to alert the driver when the airbag sensor assembly detects a malfunction in the airbag system. ·
Illuminates after the popup hood deploys. |
|
EPS Warning Light | Amber | ·
Illuminates until the hybrid system starts after the EPS warning light (red) illuminates when the electric power steering system is operating normally and the power switch is turned on (IG). ·
Illuminates when an electric power steering system malfunction which limits assist force occurs. |
| Red | ·
Illuminates for approximately 2 seconds when the electric power steering system is operating normally and the power switch is turned on (IG). ·
Illuminates when an electric power steering system assist force loss malfunction occurs. |
||
|
Brake Hold Operated Indicator Light | Amber | ·
Illuminates when the brake hold control system is operating. ·
Flashes when a malfunction occurs in the brake hold control system. |
|
Brake Warning Light (Red) | Red | ·
Illuminates for approximately 3 seconds when the brake control system is operating normally and the power switch is turned on (IG). ·
Illuminates when normal brake performance could decrease due to a malfunction in the brake actuator assembly or other part. ·
Illuminates when the brake fluid level is less than the threshold. ·
Illuminates when there is a communication malfunction with the No. 2 skid control ECU. |
|
PKSB OFF Indicator Light | Amber | ·
Illuminates when the parking support brake system is set to OFF. ·
Flashes when the parking support brake system is malfunctioning. |
|
Brake Hold Standby Indicator Light | Green | ·
Illuminates for approximately 3 seconds when the electric parking brake system is operating normally and the power switch is turned on (IG). ·
Illuminates when the brake hold standby conditions are met. |
|
PCS OFF Warning Light | Amber | ·
Illuminates for approximately 3 seconds when the pre-collision system is operating normally and the power switch is turned on (IG). ·
Illuminates when the pre-collision system is set to OFF. ·
Illuminates when the VSC system is set to OFF. ·
Illuminates when the pre-collision system is temporarily unavailable. ·
Illuminates when the pre-collision system is malfunctioning. |
|
Brake Warning Light | Amber | ·
Illuminates for approximately 3 seconds when the brake control system is operating normally and the power switch is turned on (IG). ·
Illuminates when a minor malfunction of the brake system is detected which does not prevent the vehicle from being driven. ·
Illuminates when the electric parking brake system is malfunctioning. |
|
TPWS Indicator Light | Amber | ·
Illuminates for approximately 3 seconds when the power switch is turned on (IG) during normal operation of the tire pressure warning system. ·
Illuminates when the tire pressure of any tire decreases below the threshold. ·
Illuminates/blinks when a tire pressure warning system malfunction occurs. ·
Blinks 3 times when the system starts initialization. |
Multi-information Display
Display Function Flow
The multi-information display can be switched as shown in the flow chart below:
| *a | Conditions are not met. |
| *b | Conditions are met. |
| *c | ·
Immediately interrupts and displays for 6 seconds when there is a new message display request ·
Displays each message from the highest priority for 6 seconds and then switches displays at a 2-second interval, when there are multiple massages to display |
| *d | Item or display is selected by operating the steering pad switch assembly. |
| *e | IG off to ACC or ON. |
| *f | IG ON to off (Conditions are not met). |
| *g | IG ON to off (Conditions are met). |
| *h | After IG ON |
Multi-information Display Operation
The information currently displayed can be switched by operating the steering pad switch assembly.
Fuel Economy Tab
The fuel economy tab displays information for the fuel consumption graph, digital speedometer, etc.
Fuel Consumption Graph
| Display Range | 0.0 to 99.9 kg/100km |
| Minimum Unit | 0.1 kg/100km |
| Function | ·
The average fuel consumption is calculated and displayed based on the distance traveled after starting the FC system (calculated from vehicle speed signals) and hydrogen consumption signals. ·
The displayed value is updated every 10 seconds. ·
When the value cannot be calculated, the display changes to blank. |
| Display Range | 0.0 to 99.9 kg/100km |
| Minimum Unit | 0.1 kg/100km |
| Function | ·
The total average fuel consumption is calculated and displayed based on the travel distance (calculated from vehicle speed signals) and hydrogen consumption signals. ·
The displayed value is updated every 10 seconds. ·
When the value cannot be calculated, the display changes to blank. |
| Display Range | 0.0 to 99.9 kg/100km |
| Minimum Unit | 0.1 kg/100km |
| Function | ·
The fuel consumption is calculated and displayed based on the distance traveled since the vehicle was previously refueled (calculated from vehicle speed signals) and hydrogen consumption signals. ·
The displayed value is updated every 10 seconds. ·
When the value cannot be calculated, the display changes to blank. |
| Display Range | 0 to 4 kg/100km |
| Function | ·
The current fuel consumption is calculated and displayed based on the travel distance (calculated from vehicle speed signals) and hydrogen consumption signals. ·
The displayed value is updated every 10 seconds. ·
When the value cannot be calculated, the display changes to blank. |
ECO Accelerator/ECO Score
Eco accelerator guide displays accelerator pedal operation guidelines appropriate for the current driving conditions toward the lower section of the Eco area on the FC system indicator.
Eco score displays accelerator operation guidelines appropriate for the driving conditions, and a score result based on the evaluation of driving conditions.
Driving Assist System Information Tab
The driving support tab displays the operation conditions of the dynamic radar cruise control system and the lane tracing assist system, as well as a compass and destination guidance* linked with the navigation system.
*: Models with navigation system
Audio Information Tab
Audio information displays information (status information) on audio. It also allows for audio sources to be switched and songs to be selected.
Vehicle Information Tab
The vehicle information tab displays drive information, the energy monitor and information such as tire pressure.
Drive Information
| Display Range | 0 to 999 km/h |
| Minimum Unit | 1 km/h |
| Function | ·
The average vehicle speed after starting the FC system is calculated from vehicle speed signals and displayed. ·
When the value cannot be calculated, the display changes to blank. |
| Display Range | 0.0 to 999.9 km |
| Minimum Unit | 0.1 km |
| Function | ·
The travel distance is calculated from vehicle speed signals, and the distance traveled after starting the FC system is displayed. ·
When the value cannot be calculated, the display changes to blank. |
| Display Range | 00:00 to 99:59 |
| Function | ·
The time elapsed since starting the FC system is measured, and then integrated and displayed. ·
When the value cannot be calculated, the display changes to blank. |
| Display Range | 0 to 999 km/h |
| Minimum Unit | 1 km/h |
| Function | ·
The average vehicle speed is calculated from vehicle speed signals and displayed. ·
When the value cannot be calculated, the display changes to blank. |
| Display Range | 0.0 to 999.9 km |
| Minimum Unit | 0.1 km |
| Function | ·
The travel distance is calculated from vehicle speed signals and displayed. ·
When the value cannot be calculated, the display changes to blank. |
| Display Range | 00:00 to 99:59 |
| Function | ·
The time elapsed since starting the FC system is measured and displayed. ·
The travel time is integrated until the number is reset. ·
When the value cannot be calculated, the display changes to blank. |
Energy Monitor
| Function | FC stack, EV battery and tire graphics are used to display the energy transmission direction controlled by the FC system and the EV battery charging status in real time. |
Tire Pressure
| Function | ·
Tire pressure signals are received from each tire, and this information is used to display numbers for each location where the tire is installed. ·
This will be blank if tire pressure signals cannot be received. |
Settings Tab
The items displayed on the multi-information display can be customized.
The following items can be selected on the information setting screen.
| Item | Available Setting | |
|---|---|---|
|
*1: Models with HUD *2: Models with navigation system |
||
| Change Settings | HUD Brightness/Position | ·
The brightness and position of the display can be changed. ·
When changing the brightness of the HUD image, press the right or left switch of the steering pad switch assembly. ·
When changing the position of the HUD image, press the up or down switch of the steering pad switch assembly. |
| HUD Display Setting | The following items can set to on/off: -
FC System Indicator -
Navigation*2 -
Lane -
Driving Support -
Compass -
Audio |
|
| HUD Rotation | ·
The tilt of the HUD image can be changed. ·
When changing the tilt of the HUD image counterclockwise, press the left switch of the steering pad switch assembly. ·
When changing the tilt of the HUD image clockwise, press the right switch of the steering pad switch assembly. |
|
| Item | Available Setting | |
|---|---|---|
| Change Settings | Lane Center | Center Trace ON/OFF: -
ON -
OFF |
| Alert | Alert method can be selected: -
Steering wheel vibration (Icon is displayed) -
Buzzer (Icon is displayed) |
|
| Sensitivity | Sensitivity of alert system can be changed: -
High (Icon is displayed) -
Standard (Icon is displayed) |
|
| Sway Warning | Sway warning function can be set to on/off: -
ON -
OFF |
|
| Sway Sensitivity | Sway sensitivity can be selected: -
High (Icon is displayed) -
Std. (Icon is displayed) -
Low (Icon is displayed) |
|
| Item | Available Setting | |
|---|---|---|
| Functions | System ON/OFF: -
ON -
OFF |
|
| Change Settings | Sensitivity | Pre-collision system sensitivity can be selected: -
3 (Icon is displayed) -
2 (Icon is displayed) -
1 (Icon is displayed) |
| Item | Available Setting | |
|---|---|---|
|
*: Models with RSA |
||
| Change Settings | Curve Speed Reduction | Curve Speed Reduction Adjustment: -
2 (Icon is displayed) -
1 (Icon is displayed) -
OFF |
| RSA* | System ON/OFF: -
ON -
OFF |
|
| Item | Available Setting | |
|---|---|---|
|
*: Models with BSM system |
||
| Functions | System ON/OFF: -
ON -
OFF |
|
| Change Settings | Brightness | BSM Brightness Adjustment: -
Brgt. (Icon is displayed) -
Dim (Icon is displayed) |
| Sensitivity | BSM sensitivity can be selected: -
Fast (Icon is displayed) -
Intermediate (Icon is displayed) -
Slow (Icon is displayed) -
Only Blind Spots (Icon is displayed) |
|
| Item | Available Setting | |
|---|---|---|
|
*: Models with Toyota Parking Assist-sensor System |
||
| Functions | System ON/OFF: -
ON -
OFF |
|
| Change Settings | Volume | Volume Adjustment: -
1 (Icon is displayed) -
2 (Icon is displayed) -
3 (Icon is displayed) |
| Item | Available Setting | |
|---|---|---|
|
*: Models with RCTA |
||
| Functions | System ON/OFF: -
ON -
OFF |
|
| Change Settings | Volume | Volume Adjustment: -
1 (Icon is displayed) -
2 (Icon is displayed) -
3 (Icon is displayed) |
| Item | Available Setting | |
|---|---|---|
|
*: Models with RCD |
||
| Functions | System ON/OFF: -
ON -
OFF |
|
| Change Settings | Volume | Volume Adjustment: -
1 (Icon is displayed) -
2 (Icon is displayed) -
3 (Icon is displayed) |
| Item | Available Setting |
|---|---|
|
*: Models with PKSB system |
|
| Functions | System ON/OFF: -
ON -
OFF |
| Item | Available Setting | |
|---|---|---|
|
*1: Models with RSA *2: Available setting differ by destination. |
||
| Functions | System ON/OFF: -
ON -
OFF |
|
| Change Settings | Notification Method*2 | Notification method can be selected: -
Above Speed Limit (1)
No Notification (2)
Only Visual (3)
Visual & Audio -
Overtaking (1)
No Notification (2)
Only Visual (3)
Visual & Haptic -
Others (1)
No Notification (2)
Only Visual (3)
Visual & Audio |
| Notification Level*2 | Notification level can be selected: -
10 km/h (5 mph) -
5 km/h (3 mph) -
2 km/h (1 mph) Notification level can be selected: -
5 km/h (3 mph) -
3 km/h (2 mph) -
1 km/h (1 mph) |
|
| Item | Available Setting | |
|---|---|---|
| TPWS Setting | Set Pressure | The TPWS can be initialized. |
| Change Wheel | The sensor ID can be registered. | |
| Item | Available Setting | |
|---|---|---|
|
*: Models with navigation system |
||
| Language | The language used can be selected: -
English (Default) -
Arabic -
Spanish -
Russian -
French -
German -
Italian -
Dutch -
Polish -
Hebrew -
Nor-wegian -
Swedish -
Danish -
Finnish -
Czech -
Portuguese -
Hungarian -
Flemish
|
|
| Unit | The unit displayed can be selected: -
miles (kg/100km) -
km (kg/100km)
|
|
| Fuel Economy Tab | FC System Indicator | FC system indicator can be set to on/off: -
Eco Guidance: (1)
ON (2)
OFF |
| Fuel Economy | Fuel economy can be selected: -
Trip Average -
Total Average -
Tank Average |
|
| Audio Information Tab | Audio information tab can be set to on/off: -
ON -
OFF |
|
| Settings Tab | Display Contents | Display contents can be set to on/off: -
Energy Monitor |
| Drive Info Type | Drive info type can be selected: -
Trip -
Total |
|
| Drive Info Items | Drive info items can be selected: -
Average Vehicle Speed -
Travel Distance -
Travel Time |
|
| Trip Summary | Trip summary display can be selected : -
Drive Info -
Eco Score |
|
| Pop-Up Display | Pop-up display can be set to on/off: -
TbT Navigation* -
Telephone -
Audio Operation -
Volume Operation -
Voice Control -
Brightness |
|
| Multi-information Display OFF | Multi-information display is turned off. | |
| Default Settings | Are You Sure You Want to Restore to Factory Settings?: -
Yes -
No |
|
Suggestion/Message
When a display condition is met depending on the vehicle conditions and the operations of each switch, the suggestion/message feature uses an interruption screen to display the following suggestions and messages.
| Suggestion | Display Conditions | Display | Available Setting |
|---|---|---|---|
| Headlights not turned on notification | When it is judged to be nighttime, the vehicle is being driven, and the headlights are not illuminated. | Turn ON Headlamps | - |
| Headlights not turned off after stopping notification (when headlight dimmer switch not in AUTO position) | When the ignition switch is off and the headlights are illuminated (when headlight dimmer switch not in AUTO position) | Headlamps Are ON | - |
| Headlights not turned off after stopping notification (when headlight dimmer switch in AUTO position) | When the ignition switch is off and the headlights are illuminated (when headlight dimmer switch is in AUTO position) | Headlamps Are ON Turn Headlamps OFF? | ·
Yes ·
No |
| Headlight turn off operation incomplete notification (when headlight dimmer switch in AUTO position) | When the headlights cannot be turned off after headlights not turned off after stopping notification is executed. | Headlamps can not be Turned OFF | - |
| Close door windows when wipers are operating suggestion notification | When any door window is open and the wipers are attempted to be operated. | Close Open Windows? | ·
Yes ·
No |
| Door window close operation being performed when wipers are operated notification | When a door window close operation is being performed after close door windows when wipers are operating suggestion notification is executed. | Push "OK" to Stop Windows | - |
| Door window close operation when wipers are operated incomplete notification | When the windows cannot be closed after the door window close operation being performed when wipers are operated notification is executed. | Windows cannot be Closed | - |
Warning Mode Function
Warnings are displayed by interrupting the current screen with a screen indicating that a vehicle malfunction has occurred, in order to warn the driver of the malfunction.
The warning is displayed on the multi-information display and the buzzer also sounds based on the type of warning, in order to notify the driver as quickly as possible.
If there is only 1 warning, it will continue to be displayed.
If multiple warnings are output at the same time, they will be displayed in order from highest priority level (initial display will last 6 seconds). After all warnings have been displayed once, they will be repeatedly displayed in order from highest priority level at an interval of approximately 2 seconds.
| Display | Display Conditions |
|---|---|
| Cdy-2E | When inspection mode has been entered. |
| Cdy-2 | When certification mode has been entered. |
| Shift to [P] Before Exiting Vehicle | Driver door opened with the shift position not in P |
| FCV system malfunction Do not tow this vehicle | FC system malfunction |
| Shift is in [N] Release Accelerator Before Shifting | Accelerator pedal depressed with the shift position in N |
| Traction battery system malfunction
·
Visit Your Dealer ·
Output Power Greatly Reduced Visit Your Dealer ·
Output Power Reduced Visit Your Dealer ·
[Stop] in a Safe Place See Owner's Manual ·
[Stop] in a Safe Place within 0.5 km (0.3 miles) ·
[Stop] in a Safe Place within 1.0 km (0.6 miles) ·
[Stop] in a Safe Place within 1.5 km (0.9 miles) ·
[Stop] in a Safe Place within 5.0 km (3.1 miles) ·
[Stop] in a Safe Place within 10km (6.2 miles) ·
Output power reduced Avoid shifting to [N] ·
Avoid shifting to [N] Visit Your Dealer ·
Shift to [P] See owner's manual ·
Vehicle is Unavailable Stop in a Safe Place ·
FCV system stopped Stop in a safe place |
Battery control malfunction |
| Accelerator System Malfunction
·
Visit Your Dealer ·
Output Power Greatly Reduced Visit Your Dealer ·
Output Power Reduced Visit Your Dealer ·
[Stop] in a Safe Place See Owner's Manual ·
[Stop] in a Safe Place within 0.5 km (0.3 miles) ·
[Stop] in a Safe Place within 1.0 km (0.6 miles) ·
[Stop] in a Safe Place within 1.5 km (0.9 miles) ·
[Stop] in a Safe Place within 5.0 km (3.1 miles) ·
[Stop] in a Safe Place within 10km (6.2 miles) ·
Output power reduced Avoid shifting to [N] ·
Avoid shifting to [N] Visit Your Dealer ·
Shift to [P] See owner's manual ·
Vehicle is Unavailable Stop in a Safe Place ·
FCV system stopped Stop in a safe place |
Accelerator control malfunction |
| FCV system malfunction
·
Visit Your Dealer ·
Output Power Greatly Reduced Visit Your Dealer ·
Output Power Reduced Visit Your Dealer ·
[Stop] in a Safe Place See Owner's Manual ·
[Stop] in a Safe Place within 0.5 km (0.3 miles) ·
[Stop] in a Safe Place within 1.0 km (0.6 miles) ·
[Stop] in a Safe Place within 1.5 km (0.9 miles) ·
[Stop] in a Safe Place within 5.0 km (3.1 miles) ·
[Stop] in a Safe Place within 10km (6.2 miles) ·
Output power reduced Avoid shifting to [N] ·
Avoid shifting to [N] Visit Your Dealer ·
Shift to [P] See owner's manual ·
Vehicle is Unavailable Stop in a Safe Place ·
FCV system stopped Stop in a safe place |
FC control system malfunction |
| FCV system stopped
·
Visit Your Dealer ·
Output Power Greatly Reduced Visit Your Dealer ·
Output Power Reduced Visit Your Dealer ·
[Stop] in a Safe Place See Owner's Manual ·
[Stop] in a Safe Place within 0.5 km (0.3 miles) ·
[Stop] in a Safe Place within 1.0 km (0.6 miles) ·
[Stop] in a Safe Place within 1.5 km (0.9 miles) ·
[Stop] in a Safe Place within 5.0 km (3.1 miles) ·
[Stop] in a Safe Place within 10km (6.2 miles) ·
Output power reduced Avoid shifting to [N] ·
Avoid shifting to [N] Visit Your Dealer ·
Shift to [P] See owner's manual ·
Vehicle is Unavailable Stop in a Safe Place ·
FCV system stopped Stop in a safe place |
FC control system is stopped |
| Release Accelerator
(and image display) |
Shift position is changed with the accelerator pedal depressed |
| Drive-Start Control Malfunction Visit Your Dealer
(and image display) |
Drive start control malfunction |
| Brake Override Malfunction Visit Your Dealer
(and image display) |
Brake override system malfunction |
| Accelerator and Brake Pedals Pressed Simultaneously
(and image display) |
Accelerator pedal and brake pedal are depressed simultaneously |
| Maintenance Required for Traction Battery Cooling Parts See Owner's Manual | EV battery cooling performance decreases |
| Low Auxiliary Battery See Owner's Manual | Auxiliary battery level decreases to the threshold or less |
| Accelerator Pedal is Pressed | Accelerator pedal is depressed with the shift position in P |
| Regenerative Braking Limited Press Brake to Decelerate | Regenerative braking is restricted |
| Diagnose Traction Battery | EV battery is under diagnosis |
| Maintenance Required For Traction Battery At Your Dealer | EV battery diagnosis request is established |
| Vehicle Start Will Soon Be Unavailable Maintenance Required For Traction Battery Visit Your Dealer | EV battery diagnosis request is established (re-notification) |
| Vehicle Start Unavailable Until Traction Battery Inspected Contact Your Dealer | EV battery diagnosis request is established (re-notification) |
| Fuel Gauge Malfunction Visit Your Dealer Drive Carefully as the Range May be Limited | Unable to calculate the level due to a fuel gauge malfunction |
| Unable to Start Power Supply Due to Low Temperature Restart Power Supply When FCV System Warm-up is Completed | Unable to start the plug-in control system because the FC control system is warming up |
| Br Mode is Not Available | Br mode is unavailable |
| Hydrogen Leakage Detected Visit Your Dealer | Hydrogen leak is detected (3% or more) |
| FCV System Shutdown Due to Hydrogen Leakage Stop in a Safe Place See Owner's Manual | Hydrogen leak is detected (4% or more) |
| FCV System Periodic Check Completed Normal Condition is Confirmed. | Periodic FC control system check was conducted and the result was normal |
| FCV System Periodic Check in Progress | Periodic FC control system check is in progress |
| FCV System Malfunction Visit Your Dealer | Periodic FC control system check was conducted and problems were found |
| Water Purge has Completed | FC control system drainage processing is complete |
| FCV System Purge in Progress Purge will Stop Automatically | FC control system drainage processing is in progress |
| Active Purge Mode ON | Switched to active drainage mode |
| Stop in a Safe Place Turn Power OFF Open Hydrogen Filler Door | Attempt is made to open the fuel lid when the power switch is not off, or the power switch is off with the shift position not in P |
| Open Filler Door Detected Stop in a Safe Place Close Hydrogen Filler Door | Fuel lid is open |
| Open Filler Door Detected Close Hydrogen Filler Door Restart Vehicle | Power switch is pressed with the fuel lid open |
| 12-Volt Battery Charging System Malfunction Visit Your Dealer
(and image display) |
Auxiliary battery charging system malfunction |
| FCV system overheated Output power reduced
(and image display) |
FC control system high temperature malfunction and output is restricted |
| Press brake when vehicle is stopped FCV system may overheat | FC control system may be overheating |
| Hydrogen Sensor Malfunction Visit Your Dealer
(and image display) |
Any hydrogen sensor is malfunctioning |
| Ion Filter Maintenance Required Visit Your Dealer | Ion filter must be replaced |
| Reset Complete | Ion filter replacement information is reset |
| Reset Incomplete | Failed to reset ion filter replacement information |
| FCV System Shutdown Due to Freezing Stop in a Safe Place See Owner's Manual | Unable to generate power due to a frozen FC stack |
| FCV System is Warmed Up Wait... | Rechecking for hydrogen leaks before system start |
| FCV Power Reduced | FC control system output is restricted |
| FCV Power Significantly Reduced | FC control system output is significantly restricted |
| FCV Power Reduced Due to Vehicle Tilt | Output is restricted due to a FC stack power generation malfunction caused by an inclination |
| FCV Power Reduced Due to High G | Output is restricted due to a FC stack power generation malfunction caused by high acceleration |
| FCV System High Temp. FCV Power Reduced | Output is restricted due to the high temperature of the FC control system |
| FCV System Low Temp. FCV Power Reduced | Output is restricted due to the low temperature of the FC control system |
| FCV System is Warming Up FCV Power Reduced | Output is restricted due to the FC control system warming up |
| FCV Power Reduced Due to Excessive Acceleration | Output is restricted due to the low temperature of the hydrogen tank |
| Drive Carefully | Careful driving is required |
| Drive to Flat Surface | Vehicle must be moved to a flat location |
| Press Brake to Stop Vehicle Completely Start Driving Again | Vehicle must be completely stopped for a moment |
| Stop in a Safe Place | Vehicle must be stopped in a safe location |
| Stop in a Safe Place Restart FCV System | FC control system must be restarted |
| Remaining Fuel Low Acceleration Reduced Refuel Hydrogen Now | Output is restricted due to a low hydrogen level |
| Remaining Fuel Low Refuel Hydrogen Now | Low hydrogen level |
| Remaining Fuel Low Refuel Hydrogen | Low hydrogen level |
| Display | Display Conditions |
|---|---|
| Battery Low Shifting Unavailable See Owner's Manual | Unable to change the shift position due to low auxiliary battery voltage |
| Release Accelerator to Shift | An attempt is made to change the shift position from P with both the accelerator pedal and brake pedal depressed |
| Temporarily Hold Shift Lever in [N] Position to Shift into [N] | When changing the shift position to N, the shift position is not held in N |
| Shifted Into [N] Vehicle Must be Stopped to Shift Into [R] | Shift position is changed to R while the vehicle is moving forward |
| Shifted Into [N] Shift Again to Drive | Drive force is cut while driving |
| Shifted Into [N] Vehicle Must be Stopped to Shift Into [P] | P position switch is pressed repeatedly or pressed and held while the vehicle is being driven |
| Shifted Into [N] Vehicle Must be Stopped to Shift Into [D] | Shift position is changed to D while the vehicle is reversing |
| Shifted into [P] Shift Again to Start Vehicle | A door was opened to exit the vehicle with the power switch on (IG), the shift position not in P, the brake pedal not depressed, and the driver's seat belt not fastened |
| Holding [N] Push [P] Switch When Done | Power switch is turned off after changing the shift position to N continuously 2 times |
| Shifting Unavailable Wait a Moment and Shift Again | Shift position is changed between P and another position repeatedly in a short period of time |
| Shift System Malfunction Stop in a Safe Place See Owner's Manual | Shift lever position sensor malfunction |
| Stop Vehicle in a Safe Place Push [P] Switch | Automatic P position switching function malfunction |
| Shift System Malfunction Apply Parking Brake Securely When Parking See Owner's Manual | Parking lock mechanism malfunction |
| Shift System Unavailable Apply Parking Brake Securely When Parking See Owner's Manual | FC system is stopped due to performing a power switch emergency stop while the vehicle is being driven |
| [P] Switch Malfunction Apply Parking Brake Securely When Parking See Owner's Manual | P position switch malfunction |
| Battery Low Apply Parking Brake Securely When Parking See Owner's Manual | Unable to change the shift position to P due to low auxiliary battery voltage |
| Shift System Malfunction Driving Unavailable | Electronic shift lever system malfunction and unable to drive vehicle |
| Shift System Malfunction Shifting Unavailable Drive to a Safe Place and Stop | Unable to change the shift position while driving with the shift position in D |
| Shift System Malfunction See Owner's Manual | Electronic shift lever system malfunction |
| FCV System Must be READY to Shift | Shift position is changed when the FC system has not started |
| Vehicle Must be in [D] to Shift into [Br] | Shift position is changed from P or N to Br |
| Shifted into [N] Vehicle Must be in [D] to Shift into [Br] | Shift position is changed from R to Br |
| Press Brake to Shift | Shift position is changed without depressing the brake pedal with the shift position in P |
| Display | Display Conditions |
|---|---|
| TPWS Malfunction Visit Your Dealer | Tire pressure warning system malfunction |
| Setting Tire Pressure Warning System | Tire pressure warning system is being configured |
| Tire Pressure Recalibrating Please Wait until Complete | Tire pressure warning valve/transmitter ID is registered |
| Tire Pressure Low Check Tire
(and image display) |
Tire pressure decreases below the threshold |
| Not Available
(and image display) |
Tire pressure warning system is temporarily unavailable |
| Display | Display Conditions |
|---|---|
| Braking Power Low [Stop] in a Safe Place See Owner's Manual | Brake system malfunction |
| Brake Hold Malfunction Press Brake to Deactivate Visit Your Dealer | Brake hold malfunction |
| Brake Hold Warning Press Brake on Slope | Vehicle is stopped on a steep slope and then the brake pedal is released, with brake hold in operation |
| Antilock Brake System Malfunction Visit Your Dealer | ABS malfunction |
| Braking Power Low Visit Your Dealer | Electronic control type hydraulic pressure brake system malfunction |
| Brake Hold Malfunction Visit Your Dealer | Brake hold system malfunction |
| Brake Hold Less Effective During Icy Conditions | Brake hold system is operated when the outside air temperature is low and the road surface could be frozen |
| Brake Hold Active Press Brake and Switch to Deactivate | Brake hold switch is operated without depressing the brake pedal, with brake hold in operation |
| Brake Hold Unavailable Driver Door Open | Brake hold switch is operated with the driver door open |
| Brake Hold Unavailable Driver Seat Belt Unbuckled | Brake hold switch is operated without the seat belt fastened |
| Brake Hold Unavailable Hood or Trunk Open | Brake hold switch is operated with either the hood or luggage compartment door open |
| Press Brake to Maintain Brake Hold | A certain period of time has passed with the brake pedal not depressed with brake hold in operation |
| Close Driver Door to Maintain Brake Hold | Driver door is opened with brake hold in operation |
| Fasten Driver Seat Belt to Maintain Brake Hold | Seat belt is unfastened with brake hold in operation |
| Brake Hold Unavailable | Brake hold system cannot operate temporarily |
| Brake Hold Deactivated | Brake hold system cannot operate temporarily |
| Brake Hold Deactivated Parking Brake Automatically Applied | Brake system temperature is high with brake hold in operation |
| Traction Control Turned OFF | TRC is turned off |
| Secondary Collision Brake system Malfunction Visit Your Dealer | Secondary collision brake malfunction |
| Release Accelerator
(and image display) |
Secondary collision brake is operated |
| Display | Display Conditions |
|---|---|
| EPB Shift Interlock Function Activated | Electric parking brake system automatic function is turned on |
| EPB Shift Interlock Function Deactivated | Electric parking brake system automatic function is turned off |
| EPB Automatically Applied | Parking brake is automatically applied |
| Parking Brake Unavailable | Electric parking brake system does not operate temporarily |
| Parking Brake Temporarily Unavailable | Electric parking brake system temperature is high |
| EPB Activation Stopped Incompletely | Parking brake does not operate normally and stops |
| Vehicle May Roll Park on Flat Road | Vehicle is stopped on a steep slope and the brake rotor temperature is high |
| Parking Brake Unable to Disengage Press Brake and Push Parking Brake Switch to Release | Parking brake is operated without depressing the brake pedal |
| Parking Brake Unable to Disengage Close Door and Fasten Seat Belt | Parking brake cannot be automatically released, with the driver door open or the driver's seat belt not fastened |
| Parking Brake ON | Vehicle speed is approximately 5 km/h or higher with the parking brake not released |
| Parking Brake Malfunction Visit Your Dealer | Electric parking brake system malfunction |
| Vehicle May Roll Shift into P | Shift position is not in P with the parking brake in operation |
| Display | Display Conditions |
|---|---|
| Power Steering Malfunction Steering Power Low Visit Your Dealer | Power steering system malfunction (assist stopped) |
| Voltage Abnormality Steering Power Low Visit Your Dealer | Power steering system unable to perform assist due to a power source malfunction |
| Power Steering Malfunction Visit Your Dealer | Power steering system malfunction (assist continues) |
| FCV System Stopped Steering Power Low | Power steering system unable to perform assist due to the FC system stopping |
| Display | Display Conditions |
|---|---|
| Parking Assist Malfunction Visit Your Dealer | Toyota parking assist-sensor system malfunction |
| Parking Assist Unavailable | Toyota parking assist-sensor system is temporarily stopped |
| Parking assist sensor detection display
(image display) |
Toyota parking assist-sensor system detects a stationary object |
| Temporary mute display
(image display) |
Toyota parking assist-sensor system detects a stationary object |
| Clean Parking Assist Sensor
(and image display) |
Ultrasonic sensor is dirty and frozen |
| Display | Display Conditions |
|---|---|
|
*1: Models with parking support brake system *2: Models with rear camera detection |
|
| WRITE ZERO-POINT OF STEERING ANGLE | Steering neutral point memorization is complete |
| END OF ADJUSTMENT | Steering angle adjustment is complete |
| MEMORY ERROR | Failed to adjust steering angle |
| Switch to Brake
(and image display) |
Accelerator pedal is depressed when the vehicle is stopped by the parking support brake system |
| Brake
(and image display) |
Accelerator pedal is not depressed when the vehicle is stopped by the parking support brake system |
| BRAKE! | Parking support brake system determines the possibility of a collision |
| Object Detected Acceleration Reduced | Drive force suppression control is applied by the parking support brake system |
| PKSB Malfunction Visit Your Dealer | Parking support brake system malfunction |
| PKSB Unavailable | Parking support brake system is temporarily stopped |
| Parking Support Brake Unavailable Remove the Dirt of Rear Camera*2 | |
| Display | Display Conditions |
|---|---|
|
*: Models with blind spot monitor system |
|
| Rear Cross Traffic Alert Malfunction Visit Your Dealer | Rear cross traffic alert malfunction |
| Rear Cross Traffic Alert Unavailable | Blind spot monitor sensor RH/LH or rear bumper (where blind spot monitor sensor is installed) is dirty and system does not operate |
| Blind Spot Monitor Unavailable See Owner's Manual | |
| Blind Spot Monitor Malfunction Visit Your Dealer | Blind spot monitor system malfunction |
| Display | Display Conditions |
|---|---|
|
*: Models with automatic rear flashing hazard light system |
|
| Rear Traffic Approaching | Proximity warning function for vehicles to the rear detects a vehicle approaching from the rear |
| FHL Malfunction Visit Your Dealer | Proximity warning function for vehicles to the rear malfunction |
| FHL Not Available | Proximity warning function for vehicles to the rear is temporarily stopped |
| Display | Display Conditions |
|---|---|
|
*: Models with rear camera detection |
|
| Rear Camera Detection Unavailable | Rear camera system is temporarily stopped |
| Rear Camera Detection Unavailable Remove the Dirt of Rear Camera | Rear television camera assembly is dirty and the system does not operate |
| Rear Camera Detection Malfunction Visit Your Dealer | Rear television camera assembly malfunction |
| Display | Display Conditions |
|---|---|
| Push and Hold Power Switch for Emergency Stop | Power switch is pressed while driving |
| Shift to [N] and Push POWER Switch to Restart | FC system is stopped while driving |
| FCV System Stopped Shift to P | ·
FC system is stopped with the shift position not in P or N ·
Shift position is changed to a position other than P or N with the power switch on (IG) (FC system stopped) and the vehicle stopped |
| FCV System Stopped Stop in a Safe Place | Vehicle roll warning is provided when the power switch is turned on (IG) and the FC system is stopped, with the shift position not in P or N |
| Shift to [P] Before Exiting Vehicle | ·
Power switch is turned off with the shift position not in P ·
Driver door is opened with the shift position not in P |
| Auto Power OFF to Conserve Battery | Automatic power off function is operated |
| Key Not Detected Check Key Location | ·
Electrical key is not located in the vehicle with the power switch on (IG) or on (ACC) ·
FC system starting operation is performed with the electrical key not in the vehicle ·
Vehicle starts moving (first time only) with the electrical key not in the vehicle ·
Key is taken outside the vehicle and the door is closed, with the power switch on (IG) or on (ACC) |
| Smart Entry & Start System Malfunction See Owner's Manual | Entry and start system malfunction |
| Turn Power OFF | ·
Shift position changed to P when "Shift to [P] Before Exiting Vehicle" is displayed ·
Key is taken outside the vehicle and the door is locked, with the power switch on (IG) or on (ACC) |
| Key Detected in Vehicle | Door is locked with the electrical key inside the vehicle, when the power switch is off |
| Press Brake Pedal and Touch Power Switch with Key | ·
Electrical key is not certified by the vehicle after unlocking the door with the mechanical key ·
FC system starting operation is performed 2 times with the electrical key not certified by the vehicle |
| [Not Ready To Drive] Press Brake Pedal and Push Power Switch to Start
(and image display) |
·
Driver door is opened after unlocking the door (displayed for approx. 19 seconds) ·
Power switch is turned from off to on (ACC) or on (IG) without depressing the brake pedal ·
Shift position is changed to P from a position other than P with the power switch on (IG) (FC system stopped) |
| Press Brake Pedal and Push Power Switch to Start
(and image display) |
Immobilizer certification completed via operation of the smart ignition |
| Push Power Switch while Turning Steering Wheel in Either Direction | Steering lock is not released |
| Shift to P to Start | Shift position is changed to N when the FC system can be started, with the power switch on (IG) (FC system stopped) and the vehicle stopped |
| Key Battery Low Replace Key Battery | Electrical key battery level is low |
| A New Key has been Registered Contact Your Dealer for Details | New key is registered |
| Press Brake Pedal and Push Power Switch to Start
(and image display) |
FC system start conditions are satisfied |
| Display | Display Conditions |
|---|---|
|
*: Models with theft deterrent system |
|
| Theft Sensor Turned OFF | Intrusion sensor operation is turned off |
| Theft Sensor Turned ON | Intrusion sensor operation is turned on |
| Display | Display Conditions |
|---|---|
| SRS Airbag System Malfunction Visit Your Dealer | SRS airbag system malfunction |
| Display | Display Conditions |
|---|---|
| Pedestrian Protection System Malfunction Visit Your Dealer | Pedestrian protection system malfunction |
| Pedestrian Protection System Actuated Visit Your Dealer | Driver is notified that the pedestrian protection system operated |
| Display | Display Conditions |
|---|---|
| Window Open | Any window is open when the power switch is turned off, or when the driver door is opened with the power switch turned off |
| Display | Display Conditions |
|---|---|
| Driver door open
(image display) |
·
Either a door (driver seat, front passenger seat, rear seats), the hood or the luggage compartment door is open (or ajar) ·
If multiple doors are open, they will be shown on the illustration |
| Front passenger door open
(image display) |
|
| Rear passenger door LH open
(image display) |
|
| Rear passenger door RH open
(image display) |
|
| Hood open
(image display) |
|
| Luggage compartment door open
(image display) |
| Display | Display Conditions |
|---|---|
| Wiper System Malfunction Visit Your Dealer | Wiper system malfunction |
| Display | Display Conditions |
|---|---|
| Windshield Washer Fluid Low | Washer fluid level decreases below the threshold |
| Display | Display Conditions |
|---|---|
| Headlight System Uninitialized Visit Your Dealer | System uninitialized |
| Turn Lights OFF | Taillights and headlights illuminate with the power switch turned off |
| Headlight System Malfunction Visit Your Dealer | ·
AHB (Automatic High Beam) system malfunction ·
AHS (Adaptive High Beam System) malfunction ·
Automatic headlight beam level control system malfunction ·
LED headlight system malfunction |
| Display | Display Conditions |
|---|---|
| Acoustic Vehicle Alerting System Malfunction Visit your Dealer | Vehicle proximity notification system malfunction |
| Display | Display Conditions |
|---|---|
| ERROR ADJUSTING FRONT RADAR BEAM | Failed to adjust the millimeter wave radar sensor assembly |
| ADJUSTING FRONT RADAR BEAM VERTICAL | The system has been switched to test mode (millimeter wave radar sensor assembly) |
| ADJUSTING FRONT RADAR BEAM HORIZONTAL | The system has been switched to test mode (millimeter wave radar sensor assembly) |
| CHECKING PCS BRAKE | The system has been switched to test mode (forward recognition camera) |
| BRAKE! | Warning is provided indicating a risk of collision with the preceding vehicle while the vehicle is being driven |
| Front Camera Out of Temperature Range Unavailable Wait until Normal Temperature | Forward recognition camera temperature malfunction |
| Front Camera Low Visibility Unavailable See Owner's Manual | Obstacle due to dirt or fog in front of the forward recognition camera |
| Pre-Collision System Malfunction Visit Your Dealer | Pre-collision safety malfunction |
| VSC Turned OFF Pre-Collision Brake System Unavailable | Pre-collision brake operation is stopped due to the VSC being turned off |
| Pre-Collision System Radar In Self Calibration Unavailable See Owner's Manual | Millimeter wave radar sensor assembly beam axis misalignment |
| Pre-Collision System Out of Temperature Range Unavailable See Owner's Manual | Millimeter wave radar sensor assembly temperature malfunction |
| Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor | Millimeter wave radar sensor assembly or radar cover is dirty |
| Pre-Collision System OFF | PCS (Pre-collision Safety) system is turned off |
| Front Camera Unavailable See Owner's Manual | ·
Forward recognition camera voltage malfunction ·
Forward recognition camera malfunction (other) |
| Pre-Collision System Unavailable See Owner's Manual | ·
Millimeter wave radar sensor assembly voltage malfunction ·
Millimeter wave radar sensor assembly malfunction (other) |
| Display | Display Conditions |
|---|---|
| ADJUSTING FRONT RADAR BEAM | The system has been switched to test mode (millimeter wave radar sensor assembly) |
| Dynamic radar cruise control approach warning display
(image display) |
Vehicle-to-vehicle distance with preceding vehicle decreased while the radar cruise control system is operating |
| Radar Cruise Control Unavailable See Owner's Manual | ·
Millimeter wave radar sensor assembly front surface or radar cover is dirty ·
Forward recognition camera front surface is dirty |
| Radar Cruise Control Unavailable | Measurement is difficult due to bad weather, etc. |
| Radar Cruise Control Unavailable Press Brake to Resume Driving | ·
Vehicle is stopped on a steep slope with the radar cruise control system in operation ·
Unable to detect a preceding vehicle during stop retention control |
| Cruise Control Malfunction Visit Your Dealer | Radar cruise control system malfunction |
| Cruise Control Fault Press Brake to Deactivate Visit Your Dealer | Radar cruise control system malfunction during stop retention control |
| Radar Cruise Active Please Pay Attention to Other Vehicles | Radar cruise control system is turned on |
| Dynamic radar cruise control normal control display
(image display) |
Radar cruise control system is in operation |
| Display | Display Conditions |
|---|---|
| ADJUSTING FORWARD CAMERA | The system has been switched to test mode (forward recognition camera) |
| Lane tracing assist approach warning display
(image display) |
Vehicle determined to have departed from lane while driving |
| LTA Hold Steering Wheel
(and image display) |
Hands-off judgment signal received while the lane tracing assist system is starting |
| LTA Steering Assist Unavailable Hold Steering Wheel
(and image display) |
Lane tracing assist system receives a hands-off judgment signal and then stops |
| LTA Malfunction Visit Your Dealer
(and image display) |
Lane tracing assist system malfunction |
| LTA Unavailable
(and image display) |
Lane tracing assist system is temporarily stopped |
| LTA Steering Assist Active Lane Centering Active
(and image display) |
Lane tracing assist system is started |
| LTA Steering Assist Active
(and image display) |
|
| LTA Unavailable at Current Speed
(and image display) |
Lane tracing assist system operation speed range is exceeded |
| Lane tracing assist normal control display
(image display) |
Lane tracing assist system is in operation |
| Would You Like to Take a Break?
(and image display) |
Vehicle lane departure is detected |
| Display | Display Conditions |
|---|---|
|
*: Models with RSA |
|
| RSA Malfunction Visit Your Dealer | Road sign assist system malfunction |
| Display | Display Conditions |
|---|---|
|
*: Models with advanced park |
|
| Advanced Park Active [Advanced Park Switch Icon] : Cancel | Advanced park is in operation |
| Advanced Park Malfunction Visit Your Dealer | Advanced park malfunction |
| Advanced Park Malfunction Press Brake Pedal | Brake operation is required due to an advanced park malfunction |
| Advanced Park Canceled Press Brake Pedal | Advanced park is stopped |
Buzzer
The table below shows the warning and reminder functions of the buzzer in the combination meter assembly:
| Priority | Item | Sounding Pattern | Frequency
(Hz) |
Period
(sec.) |
ON Duty
(sec.) |
Time Constant |
|---|---|---|---|---|---|---|
| 1 | READY | Once | 800 | 0.2 | - | - |
| 2 | Advanced Park Warning Buzzer | 2 Times | 1.6k | 0.2 | 0.1 | - |
| 3 | Once | 800 | 1.0 | - | - | |
| 4 | Once | 1.6k | 0.2 | - | - | |
| 5 | Once | 1.6k | 1.1 | - | - | |
| 6 | Pre-collision System Warning | Intermittent | 2.4k | 0.2 | 0.1 | - |
| 7 | Dynamic Radar Cruise Control System Proximity Warning Buzzer | Intermittent | 2.4k | 0.2 | 0.1 | - |
| 8 | EPS Warning | Intermittent | 1.6k | 0.4 | 0.2 | - |
| 9 | Electrical Ignition Switch Control | Intermittent | 1.6k | 0.4 | 0.2 | - |
| 10 | Brake Fluid Low Warning | Intermittent | 1.6k | 0.4 | 0.2 | - |
| 11 | Lane Tracing Assist System Cancel Warning | 2 Times | 1.6k | 0.2 | 0.1 | - |
| 12 | Hands off Steering Wheel Warning | Intermittent | 800 | 0.7 | 0.35 | - |
| 13 | Secondary Collision Brake Operation Buzzer | Intermittent | 1.6k | 0.4 | 0.2 | - |
| 14 | EV System Warning | Intermittent | 1.6k | 0.2 | 0.1 | - |
| 15 | Intermittent | 1.6k | 0.4 | 0.2 | - | |
| 16 | Intermittent | 1.6k | 0.7 | 0.35 | - | |
| 17 | Intermittent | 1.6k | 1.2 | 0.6 | - | |
| 18 | Continuous | 1.6k | - | - | - | |
| 19 | Once | 1.6k | 0.9 | - | - | |
| 20 | Towing Prohibition Notice Buzzer | Intermittent | 1.6k | 0.4 | 0.2 | - |
| 21 | Hydrogen Leak 4.0% or more Detected Warning | Intermittent | 1.6k | 0.9 | 0.45 | - |
| 22 | FC System Warning | Once | 1.6k | 0.9 | - | - |
| 23 | Continuous | 1.6k | - | - | - | |
| 24 | Intermittent | 1.6k | 0.2 | 0.1 | - | |
| 25 | Intermittent | 1.6k | 0.4 | 0.2 | - | |
| 26 | Intermittent | 1.6k | 0.7 | 0.35 | - | |
| 27 | Intermittent | 1.6k | 1.2 | 0.6 | - | |
| 28 | Accelerator Hold Warning | Continuous | 800 | - | - | - |
| 29 | Shift Reject Warning | 2 Times | 1.6k | 0.13 | 0.065 | - |
| 30 | Accelerator Depression in N Position | Continuous | 800 | - | - | - |
| 31 | Automatic P Position Switching Buzzer When Exiting Vehicle | Intermittent | 1.6k | 0.4 | 0.2 | - |
| 32 | Brake Hold System Control Not Release Warning | Intermittent | 1.6k | 0.4 | 0.2 | - |
| 33 | Reverse Warning Buzzer | Once | 1.6k | - | - | - |
| 34 | Rear Seat Belt Warning | Once | 800 | 1.2 | - | 0.8 |
| 35 | Seat Belt Warning (Level 2) | Intermittent | 800 | 0.4 | - | 0.8 |
| 36 | Seat Belt Warning (Level 1) | Intermittent | 800 | 1.2 | - | 0.8 |
| 37 | Brake System Low Braking Force Warning Buzzer | Intermittent | 1.6k | 0.4 | 0.2 | - |
| 38 | Brake System Non-operation Buzzer | Intermittent | 1.6k | 0.4 | 0.2 | - |
| 39 | Brake System Malfunction Buzzer | Intermittent | 1.6k | 0.4 | 0.2 | - |
| 40 | Brake System Non-operation Buzzer | Intermittent | 1.6k | 0.2 | 0.1 | - |
| 41 | EV Unit Overheat Warning | Once | 800 | 0.9 | - | 0.8 |
| 42 | P Position Operation Advice Buzzer | Continuous | 800 | - | - | - |
| 43 | Door Open while Driving Warning Buzzer | Intermittent | 1.6k | 0.7 | 0.35 | - |
| 44 | FC System Start while Driving Reminder | Continuous | 800 | - | - | - |
| 45 | Door Open when Shift Lever Not in P Warning | Continuous | 800 | - | - | - |
| 46 | Smart Key System Warning | Continuous | 800 | - | - | - |
| 47 | Road Sign Assist System Buzzer | Once | 800 | 0.9 | - | 0.8 |
| 48 | Dynamic Radar Cruise Control Brake Operation Request Buzzer | Intermittent | 2.4k | 0.4 | 0.2 | - |
| 49 | Vehicle Sway Warning | 2 Times | 1.6k | 0.2 | 0.1 | - |
| 50 | Sport Shift Reject Warning | 2 Times | 1.6k | 0.13 | 0.065 | - |
| 51 | Dynamic Radar Cruise Control Speed Exceeded Buzzer | Intermittent | 800 | 0.7 | 0.35 | - |
| 52 | EPS Warning | Once | 800 | 0.9 | - | 0.8 |
| 53 | Shift-by-wire Buzzer | Once | 1.6k | 0.9 | - | - |
| 54 | Warning Mode Display Interlocking Buzzer | Once | 800 | 0.9 | - | - |
| 55 | Brake system temperature increase/Active Test buzzer | Intermittent | 1.6k | 0.2 | 0.1 | - |
| 56 | Fuel Lid Release Warning | Intermittent | 800 | 1.2 | 0.6 | - |
| 57 | Brake Hold System Control Not Release Warning | 2 Times | 1.6k | 0.2 | 0.1 | - |
| 58 | Entry and Start System Warning Buzzer | Once | 800 | 0.9 | - | 0.8 |
| 59 | Light Reminder | Continuous | 800 | - | - | - |
| 60 | HV Battery Diagnostic Request Notice Buzzer | Intermittent | 800 | 0.7 | 0.35 | - |
| 61 | EV Battery Cooling Performance Deterioration Warning Buzzer | Once | 800 | 0.9 | - | - |
| 62 | Entry and Start System Warning Buzzer | Intermittent | 800 | 1.2 | 0.6 | 0.8 |
| 63 | Intermittent | 800 | 0.7 | 0.35 | - | |
| 64 | Brake System App Drive Notification Buzzer | Intermittent | 1.6k | 0.4 | 0.2 | - |
| 65 | Intermittent | 1.6k | 0.2 | 0.1 | - | |
| 66 | 2 Times | 1.6k | 0.13 | 0.065 | - | |
| 67 | Fuel Lid Opening Not Possible Warning Buzzer | 2 Times | 1.6k | 0.13 | 0.065 | - |
| 68 | Electrical Ignition Switch Control | Once | 1.6k | 0.13 | - | - |
| 69 | PBA Notification | Intermittent | 2.4k | 0.1 | 0.05 | - |
| 70 | ALM Notification | Intermittent | 2.4k | 0.2 | 0.1 | - |
| 71 | Brake Inspections Standby Mode Notification | Intermittent | 2.4k | 0.4 | 0.2 | - |
| 72 | Radar Axis Adjustment Complete Notification | Intermittent | 2.4k | 0.5 | 0.25 | - |
| 73 | Camera Axis Adjustment Complete Notification | Intermittent | 2.4k | 1.0 | 0.5 | - |
| 74 | FPB/PB / Brake Inspection Normal Return / Radar Axis Adjustment Incomplete / Camera Adjustment Start Notification | Continuous | 2.4k | - | - | - |
| 75 | Brake System Test Mode | Intermittent | 1.6k | 0.2 | 0.1 | - |
| 76 | Once | 1.6k | 0.13 | - | - | |
| 77 | 2 Times | 1.6k | 0.13 | 0.065 | - | |
| 78 | Fuel Lid Release Prohibited Warning | 2 Times | 1.6k | 0.13 | 0.065 | - |
| 79 | Br Mode Reject Warning Buzzer | 2 Times | 1.6k | 0.13 | 0.065 | - |
| 80 | FC Water Release Switch not Available Buzzer | 2 Times | 1.6k | 0.13 | 0.065 | - |
| 81 | Turn Signal/Hazard Warning Operation | Intermittent | When turn signal light is operating, sounds intermittently. | |||