Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
NM37H0E _51 Engine / Hybrid System _097147 HYBRID / BATTERY CONTROL _0466531 HYBRID CONTROL SYSTEM CO CONTROL F

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  CONTROL  HYBRID CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
EV Control ECU
·

Performs driving and electrical distribution based on the signals from each sensor and ECU.

·

Monitors the EV supply battery assembly condition (battery voltage / current / temperature)

·

Controls the water pump with motor assembly to adjust the output quantity.

·

Optimally controls the amount of hydrogen and oxygen supplied to the FC stack assembly.

·

Sends cooling fan spinning request signals to the fan with motor assembly, and optimally controls the FC stack coolant temperature.

·

Performs cooperative control with the No. 2 skid control ECU and regenerative breaking system.

·

Actuates the System Main Relays (SMRs) to connect and disconnect the high voltage circuits from the EV supply battery assembly.

·

Controls the DC-DC converter to step down the DC 310.8 V of the EV supply battery assembly to DC 14 V.


FC Control ECU Operates the fuel injector assembly based on signals from the EV control ECU.
Accelerator Pedal Rod with Sensor Assembly Detects the accelerator opening angle and sends it to the EV control ECU.
Shift Control ECU Requests the EV control ECU to change to the shift range or the Br mode according to the shift lever position, based on the signal (R, N, D or Br) from the shift lever position sensor and the vehicle status.
Inverter with Converter Assembly MG ECU According to the output value requested from the EV control ECU, operates the inverter and boost converter, and controls the electric motor (traction motor) and FC air compressor.
Inverter Converts between high voltage DC and three phase AC.
Converter
·

Boosts the EV supply battery assembly voltage to a maximum of DC 650 V.

·

Steps down the FC stack assembly voltage and the high voltage (max. 650 V) from the inverter.


DC-DC Converter Steps down the voltage of the high voltage system to approximately DC 14 V and provides it to accessory components and the auxiliary battery.
FCV Transaxle with Motor Assembly Electric Motor (Traction Motor) Based on driving conditions, uses the electrical energy from the FC stack assembly and the electrical energy from the EV supply battery assembly to generate driving force. Also, uses regenerative braking to generate electricity when decelerating.
FC Air Compressor with Motor Assembly
·

Supercharges the air that has passed the air cleaner and provides it to the FC stack assembly.

·

Driven by the inverter of the inverter with converter assembly.


FC Stack Assembly FC Stack Generates electrical energy by causing a chemical reaction between hydrogen fuel from the hydrogen tank and oxygen from the FC air compressor with motor assembly.
FC Stack Voltage Sensor Detects the output voltage of the FC and sends it to the FC control ECU.
FC Converter Assembly FC Boost Converter Boosts the voltage of the electrical energy generated in the FC stack assembly to a maximum of DC 650 V.
FC DC converter control ECU Board sub-assembly Sends MOSFET on and off signals to the FC converter power module transistor.
FC Converter Power Module Transistor Turns the Metal Oxide Semiconductor Field Effect Transistor (MOSFET) on/off based on signals from the FC DC converter control ECU board sub-assembly.
Reactor Changes the current and boosts the voltage according to the MOSFET turning on or off.
FRB (FC Stack Main Relay) Based on the signal from the EV control ECU, connects and disconnects the high voltage circuits of the FC stack assembly.
FRG (FC Stack Main Relay)
FRP (Precharge Relay)
EV Supply Battery Assembly No. 1 EV Supply Stack Sub-assembly
·

Stores the electrical power generated by the FC stack as well as the electrical power regenerated through regenerative braking of the electric motor (traction motor).

·

Supplies electrical power to the electric motor (traction motor) when starting out, accelerating, etc.


No. 2 EV Supply Stack Sub-assembly
Battery ECU Assembly
·

Monitors the conditions of the EV supply battery assembly such as voltage, current and temperature, and transmits this information to the EV control ECU.

·

Controls the battery cooling blower assemblies.


Battery Voltage Sensor Connected to the battery ECU assembly via a communication wire and sends information required for calculations performed by the EV control ECU.
System Main Relays (SMRs) Connects and disconnects the high voltage circuits of the EV supply battery assembly based on the signals from the EV control ECU. The EV control ECU assembly controls the SMRs by turning them on or off as appropriate.
EV Battery Current Sensor Measures the current of the No. 1 EV supply stack sub-assembly and No. 2 EV supply stack sub-assembly.
EV Battery Temperature Sensors Detects temperatures in the parts of the No. 1 EV supply stack sub-assembly, No. 2 EV supply stack sub-assembly and the intake air temperature from the battery cooling blower assembly.
Battery Cooling Blower Assembly Operates under the control of the battery ECU assembly in order to cool the EV supply battery assembly.
Service Plug Grip Removed during inspection or service to disconnect the high voltage circuits of the EV supply battery assembly.
Drive Mode Select Switch (No. 1 Pattern Select Switch Assembly) Switches the drive mode between the following 3 modes.
·

NORMAL mode

·

ECO mode

·

SPORT mode


Snow Mode Switch (Pattern Select Switch Assembly) Switches to SNOW mode.
Stop Light Switch Assembly Detects the brake pedal on/off condition.
Battery State Sensor Assembly Calculates the current, voltage, temperature, SOC (battery charging percentage) and SOH (battery degradation percentage) of the auxiliary battery.
Water Pump with Motor Assembly Circulates coolant in order to cool the FC converter assembly, inverter with converter assembly and FC Air Compressor with Motor Assembly.
Brake Actuator Assembly No. 2 Skid Control ECU
·

When braking, calculates the necessary regenerative braking force and sends it to the EV control ECU, and at the same time controls the hydraulic brakes.

·

When traction control system (TRC) or vehicle stability control (VSC) is operating, sends requested torque to the EV control ECU, and controls driving force.

·

Sends the motor traction control requested torque to the EV control ECU, and controls braking force of the brakes.


Airbag ECU (Airbag ECU Assembly) In a collision, sends the collision detection signal to the EV control ECU.
Air Conditioning Amplifier Assembly Sends compressor with motor assembly speed control instruction signal drive request signal and electric heater sub-assembly power command signals to the EV control ECU, and controls the air conditioner system.
Combination Meter Assembly READY Indicator Light Indicates a status in which driving is possible.
ECO Mode Indicator Indicates that ECO mode is selected.
SPORT Mode Indicator Indicates that SPORT mode is selected.
SNOW Mode Indicator Indicates that SNOW mode is selected.
Br Mode Indicator Indicates that Br mode is selected.
Hydrogen Leak Warning Light Illuminates when a hydrogen leak has been detected.
Shift Position Indicator Displays the selected shift position.
Buzzer When there is a system malfunction, the buzzer sounds depending on the contents of the malfunction.
Multi-information Display
·

Displays the FC system output status via the energy monitor.

·

Displays the FC system output and regeneration status using the FC system indicator.

·

Displays a message when the system is malfunctioning.




SYSTEM CONTROL


a.

Based on a number of driving conditions, the EV control ECU provides an optimum amount of electrical energy to the electric motor (traction motor) to realize smooth and powerful driving in response to driver demands. Also, it monitors and controls EV supply battery assembly conditions and high voltage circuits, uses cooperative control with the No. 2 skid control ECU for regenerative braking, etc., and comprehensively performs various controls relating to the FC system.

System Control List
Item Function
FC System Output Control Based on the accelerator opening angle signal, shift position signal and vehicle speed signal, the EV control ECU performs control of FC system output by calculating the FC stack electrical output power, FC air compressor motor torque and the electric motor (traction motor) torque according to the driver request, and sending requested values to each ECU.
FC Stack Current and Boost Control The FC DC converter control ECU board sub-assembly controls the output current from the FC stack so that it is as requested by the command from the EV control ECU, and boosts the voltage to 650 V.
Brake Cooperative Control and Regenerative Brake Control When decelerating, the No. 2 skid control ECU calculates the necessary regenerative braking force and sends the value to the EV control ECU. When this happens, the EV control ECU sends the actual regenerative braking value to the No. 2 skid control ECU, and based on this, the No. 2 skid control ECU controls the hydraulic braking force.
Collision Control When an airbag deployment signal from the airbag ECU is detected, the high voltage circuits and hydrogen fuel supply lines are shut off.
Brake Override Control The FC system output is restricted when both the accelerator and brake pedals are depressed. (For the activation conditions and inspection method, refer to the Repair Manual)
Drive Start Control If an abnormal shift (R to D, D to R, N to R, P to D, P to R) is detected while accelerating, a warning is displayed in the combination meter assembly and FC system output is reduced to limit the acceleration, helping to avoid a collision.


b.

FC System Activation

i.

The FC system can be activated by pressing the ignition switch while the brake pedal is being depressed.

HINT:

The FC relay built into the FC converter assembly and hydrogen tank valve installed in the hydrogen tank are operated when starting and stopping, and an operating sound may be heard.



ii.

If the FC stack coolant temperature is low at the time the FC system is started, startup time will become longer and so the following screen will be displayed on the multi-information display in the combination meter assembly.

Multi-information Display Screen
W147875

·

When the intake air temperature after passing through the intercooler is 0°C (32°F) or less or the FC stack coolant temperature after passing through the FC stack is 0°C (32°F) or less, quick warmup is performed in addition to the normal start sequence to ensure starting performance in low outside air temperature.

·

When the vehicle is being driven in low outside air temperature (0°C (32°F) or less), a freeze prevention process is conducted in addition to the normal stop sequence to ensure starting performance in low outside air temperature.



iii.

While the FC system is starting up, pressing the ignition switch again will stop the system.


iv.

While the vehicle is being driven, ignition switch operation is canceled.*

HINT:

*: If a situation arises in which it is absolutely necessary to stop the FC system while the vehicle is being driven, rapidly pressing the ignition switch 2 times or more, or pressing and holding the ignition switch for 2 seconds or more, will forcibly stop the FC system and the ignition position will be changed to ACC.


W107197C02
2.25,1.469 2.563,1.625 0.313,0.156 10 *1 4.865,1.219 5.177,1.375 0.313,0.156 10 *2
*1 Power Switch (Push Start Switch) *2 READY Indicator Light (Inside Combination Meter Assembly)



v.

When there is a start request by operation of the driver's switch, high voltage and hydrogen fuel safety checks will be performed and then the system will start. Then, when the ignition switch is turned off, exhaust water processing and hydrogen fuel leak checks will be performed and then the system will turn off.



c.

FC System Output Control

i.

The EV control ECU determines the total output according to the driving conditions based on the output requested by the driver (calculated based on the accelerator opening angle, shift position signal and vehicle speed signal), and sends request signals to each ECU to control drive force. Additionally, it calculates the amount of required air and hydrogen based on the total calculated output.


ii.

The FC control ECU controls the fuel injector assembly and the EV control ECU controls the hydrogen recirculation pump assembly based on the FC output calculated by the EV control ECU, and ensures sufficient hydrogen required for power generation.


iii.

Based on the torque request from the EV control ECU, the MG ECU controls the FC air compressor with motor assembly and the driving force of the electric motor (traction motor).

W147919E02
0.281,0.51 1.719,1.031 1.438,0.521 10 false Accelerator Pedal Rod with Sensor Assembly 1.99,0.875 3.25,1.313 1.26,0.438 10 false Accelerator opening angle 0.458,1.448 2.188,1.75 1.729,0.302 10 false Shift Control ECU 2.01,1.656 3.229,2.042 1.219,0.385 10 false Shift position signal 0.135,2.115 1.854,2.479 1.719,0.365 10 false Battery ECU Assembly 0.156,2.51 1.635,2.854 1.479,0.344 10 false - EV battery voltage 0.156,2.896 1.667,3.271 1.51,0.375 10 false - EV battery current 0.146,3.271 1.698,3.625 1.552,0.354 10 false - EV battery temperature 2.083,2.906 3.135,3.323 1.052,0.417 10 false EV battery state signal 0.208,4.354 1.896,4.688 1.688,0.333 10 false - Skid Control ECU No. 2 0.125,3.906 1.854,4.208 1.729,0.302 10 false Brake Actuator Assembly 1.958,3.958 3.229,4.469 1.271,0.51 10 false Regenerative braking request value 1.99,5.052 3.198,5.5 1.208,0.448 10 false Regenerative brake execution value 3.438,0.219 4.521,0.708 1.083,0.49 10 false EV Control ECU 3.563,0.771 4.354,1.25 0.792,0.479 10 false Driver output request 3.552,2.313 4.396,2.802 0.844,0.49 10 false Total request output 3.573,3.594 4.333,4.052 0.76,0.458 10 false Driving force control 5.375,2.802 6.635,3.458 1.26,0.656 10 false - Required hydrogen amount calculation 5.354,3.5 6.698,4.083 1.344,0.583 10 false - Required air amount calculation 4.917,1.688 6,2.438 1.083,0.75 10 false Injector operation command signal 5.521,0.76 6.604,1.219 1.083,0.458 10 false FC Control ECU 5.823,5.469 6.99,6.021 1.167,0.552 10 false FC air compressor request 3.896,5.542 5.26,5.865 1.365,0.323 10 false Required motor torque 4.406,7.885 6.948,8.188 2.542,0.302 10 false FC Air Compressor with Motor Assembly 4.99,6.604 6.646,6.927 1.656,0.323 10 false FC air compressor control 2.521,6.604 4.833,6.969 2.313,0.365 10 false Electric motor (traction motor) control 1.781,6.375 2.365,6.667 0.583,0.292 10 false MG ECU 0.188,6.302 1.542,6.729 1.354,0.427 10 false Inverter with Converter Assembly 1.917,8.302 3.823,8.635 1.906,0.333 10 false Electric Motor (Traction Motor) 5.021,8.302 6.594,8.688 1.573,0.385 10 false FC Air Compressor Motor 1.719,7.906 3.979,8.292 2.26,0.385 10 false FCV Transaxle with Motor Assembly


iv.

In certain situations, the FC system will judge the vehicle conditions and perform output restriction. While output restriction is in effect, the intended level of vehicle acceleration might not be obtainable.

·

Output restriction due to FC control system temperature increase (restriction by EV control ECU and FC control ECU)

When continuously driving uphill or driving at a high output level at high altitude has caused the temperature of the FC cooling system to increase, the electrical power supplied to the electric motor (traction motor) will be restricted, and a message will be displayed in the multi-information display of the combination meter informing that output has been restricted due to high temperature of the FC cooling system. When the temperature of the FC cooling system returns to the normal range, the restriction will be canceled.

·

Output restriction due to inverter and the electric motor (traction motor) temperature increase (restriction by EV control ECU)

When the temperature of the powertrain system cooling system increases due to high-load driving, the power supplied to the electric motor (traction motor) will be restricted. Restrictions are released when the temperature of the inverter and electric motor (traction motor) returns to normal.

·

Output restriction when starting at freezing temperatures (restriction by EV control ECU)

When the system is started at temperatures below freezing, the fuel cell performance is reduced. As the FC stack coolant temperature increases, the output restriction is gradually removed.

·

Output restriction due to low fuel remaining (restriction by EV control ECU)

When the amount of hydrogen fuel remaining in the hydrogen tank has decreased to the specified value (6%) or less, a message will be displayed informing that output is restricted due to low fuel remaining. If the vehicle continues to be driven, when the remaining hydrogen fuel pressure is 1 MPa or less, the FC control system will stop and electrical generation will stop. If the State of Charge (SOC) of the EV supply battery assembly is low, the vehicle will also stop.

·

Output restriction due to FC air compressor with motor assembly temperature (restriction by EV control ECU)

If the temperature of the built-in motor of the FC air compressor with motor assembly has increased, or if the compressor portion temperature has decreased, output will be restricted to protect the FC air compressor with motor assembly.

·

When repeated accelerations and decelerations have been performed continuously, the EV supply battery assembly is being subjected to abrupt charging and discharging, which can result in temperature increases or reductions of the SOC, causing reduced power output. Also, in a low temperature environment, output will also be reduced if the EV battery temperature is low.




d.

FC Stack Current and Boost Restrictions

i.

Based on requests from the EV control ECU, the FC DC converter control ECU board sub-assembly built into the FC converter assembly controls the FC stack assembly output current based on the requests from the EV control ECU, and boosts the voltage to a maximum of 650 V and supplies it to the inverter with converter assembly.

W125764E02
0.219,0.188 2.365,0.385 2.146,0.198 10 false EV Control ECU 0.229,1.813 2.833,2.01 2.604,0.198 10 false FC Stack Assembly 1.594,0.823 2.552,1.302 0.958,0.479 10 false Output current value 2.823,0.313 3.927,0.813 1.104,0.5 10 false FC DC Converter Control ECU Board Sub-assembly 2.896,1.802 4.885,2 1.99,0.198 10 false FC Boost Converter 5.448,1.521 6.844,2.198 1.396,0.677 10 false Inverter with Converter Assembly 4.583,2.063 5.208,2.49 0.625,0.427 10 false Maximum 650 V 1.604,2.104 2.5,2.552 0.896,0.448 10 false FC stack output voltage 2.729,2.375 5.938,2.573 3.208,0.198 10 false FC Converter Assembly


ii.

The FC converter power module transistor increases the number of drive phases from 2 only during a low load to 3 then 4 during a medium and then high load according to commands from the FC DC converter control ECU board sub-assembly which has received the current command value requested by the EV control ECU, in an attempt to reduce MOSFET switching loss and improve fuel efficiency.



e.

Electronically Controlled Brake Control

i.

Electronically controlled hydraulic brake control and cooperative control

·

The electronically controlled hydraulic brake system uses communication between the EV control ECU and the No. 2 skid control ECU to cooperatively control the regenerative braking force from the electric motor (traction motor) and the braking force from the hydraulic brake in order to perform regenerative cooperative brake control that can effectively reuse the driving energy.

W125765E02
0.135,0.521 1.031,0.958 0.896,0.438 10 false Driver braking request 1.49,0.385 3.938,0.583 2.448,0.198 10 false No. 2 Skid Control ECU 1.479,1.531 4.844,1.729 3.365,0.198 10 false Hydraulic Control Unit 5.844,0.26 6.938,0.646 1.094,0.385 10 false EV Control ECU 3.427,0.542 5.604,0.896 2.177,0.354 10 false Regenerative braking request value 3.427,0.917 5.604,1.271 2.177,0.354 10 false Regenerative brake execution value 0.844,2.344 4.375,2.698 3.531,0.354 10 false Brake Booster with Master Cylinder Assembly

·

The No. 2 skid control ECU detects the driver's brake operation amount, and sends the calculated regenerative brake braking force request value to the EV control ECU. Based on the requested value, the EV control ECU performs regenerative brake control, and at the same time sends the actual regenerative brake control value to the No. 2 skid control ECU.

W148164E02
2.958,1.573 2.125,1.135 2.125,1.135 1.896,1.135 true 5.438,1.219 5.219,1.219 5.219,1.219 4.573,1.802 true 5.177,0.167 4.958,0.167 4.958,0.167 4.625,0.51 true 2.073,2.24 2.948,2.438 0.875,0.198 10 false Start Braking 4.75,2.26 5.792,2.438 1.042,0.177 10 false Vehicle Stop 1.031,1.031 1.938,1.229 0.906,0.198 10 false Friction Brake 5.25,0.052 7.01,0.594 1.76,0.542 10 false Braking force corresponding to the brake pedal operation. 1.51,0.521 2.521,0.854 1.01,0.333 10 false Braking Force 5.5,1.146 6.771,1.354 1.271,0.208 10 false Regenerative Brake



ii.

Regenerative Brake Control

·

The electrical energy from the regenerative braking is used to charge the EV supply battery assembly.




f.

Control in a Collision

i.

When the vehicle has received a strong impact and an airbag operation signal has been received from the airbag ECU, the FC system turns off the hydrogen tank shut valve relay to shut off the flow of hydrogen fuel, and at the same time turns off the SMR and FC relay, shutting off the high voltage power supply circuits to ensure safety.



g.

Drive Start Control

·

When abnormal driver accelerator pedal and shift operations are detected, the system limits the motive force and informs the driver.

W147920E01
0.219,0.177 1.896,0.896 1.677,0.719 10 false Accelerator Pedal Rod with Sensor Assembly 0.427,1.354 2.073,2.073 1.646,0.719 10 false Shift Control ECU 0.177,2.479 1.667,3.188 1.49,0.708 10 false Electric Motor (Traction Motor) Rotation Sensor 2.156,2.635 2.833,3.031 0.677,0.396 10 false MG ECU 0.417,3.771 1.646,4.479 1.229,0.708 10 false Airbag ECU (Airbag ECU Assembly) 0.302,4.979 1.771,5.438 1.469,0.458 10 false No. 2 Skid Control ECU 3.427,2.49 4.146,2.917 0.719,0.427 10 false EV Control ECU 5.198,0.677 7.021,1.396 1.823,0.719 10 false Combination Meter Assembly 5.406,2.094 6.896,2.802 1.49,0.708 10 false Headup Display (Meter Mirror Sub-assembly)* 5.563,3.563 6.74,4.063 1.177,0.5 10 false FC System Output Request 4.708,4.813 7.031,5.5 2.323,0.688 10 false *: Models with Headup Display (Meter Mirror Sub-assembly)

HINT:

When the system is operating, even if the driver depresses and holds the accelerator pedal, FC system output may increase on an uphill slope and decrease on a downhill slope. This behavior allows the system to restrict the vehicle speed and acceleration below the predetermined limit on slopes and is not a malfunction.



i.

Control during Shift Operation

·

Responds to shift operations with the accelerator pedal depressed.

·

Changes the limit amount according to the manual shift operation pattern.

·

Corrects FC system output according to the road grade.

Control when Starting Off from a Parked Position

*: Depending on the situation, the shift position may not be change.

Control Start Conditions (When all of the following conditions are met, control starts.)
·

Shift state is changed from P to D*, or P to R*.

·

Accelerator opening angle is approximately 1/5 or higher.


Control Operation Restricts the FC system output so the vehicle speed and acceleration are at or below a certain level.
Control Stop Conditions
·

Accelerator pedal is fully released.

·

Shift state is P or N.



Image of Control when Starting Off from a Parked Position
W122967E22
4.427,1.802 4.854,1.802 true 1.833,0.198 2.531,0.396 0.698,0.198 10 false Shift State 1.427,0.552 2.615,0.75 1.188,0.198 10 false Accelerator Pedal 2.823,0.208 3.021,0.417 0.198,0.208 10 false P 3.385,0.208 3.583,0.417 0.198,0.208 10 false D 2.771,0.563 2.969,0.771 0.198,0.208 10 false On 3.031,0.833 3.938,1.021 0.906,0.188 10 false Control Starts 1.854,1.479 2.625,1.865 0.771,0.385 10 false FC System Output 4.927,1.75 5.75,1.958 0.823,0.208 10 false Restricted 5.229,2.25 6.073,2.438 0.844,0.188 10 false With Control 3.667,2.469 4.146,2.656 0.479,0.188 10 false Time 5.26,1.365 6.365,1.573 1.104,0.208 10 false Without Control

Control during Other Situations
Control Start Conditions (When all of the following conditions are met, control starts.)
·

Shift state is changed from R to D/S, D/S to R, or N to R.

·

Accelerator opening angle is approximately 1/5 or higher.


Control Operation Restricts the FC system output so the vehicle speed and acceleration are at or below a certain level.
Control Stop Conditions
·

Accelerator pedal is fully released.

·

Shift state is P or N.



Image of Control during Other Situations
W122968E15
4.406,1.74 4.74,1.74 true 1.677,0.208 2.594,0.406 0.917,0.198 10 false Shift State 1.417,0.563 2.573,0.771 1.156,0.208 10 false Accelerator Pedal 3.042,0.833 3.958,1.042 0.917,0.208 10 false Control Starts 3.385,0.219 3.573,0.417 0.188,0.198 10 false R 2.823,0.219 3.01,0.417 0.188,0.198 10 false N 2.771,0.573 3,0.76 0.229,0.188 10 false On 5.292,1.344 6.448,1.552 1.156,0.208 10 false Without Control 5.292,2.135 6.448,2.344 1.156,0.208 10 false With Control 1.844,1.615 2.615,2.01 0.771,0.396 10 false FC System Output 3.802,2.469 4.188,2.667 0.385,0.198 10 false Time 4.781,1.677 5.583,1.927 0.802,0.25 10 false Restricted

CAUTION:
·

The FC system output restraint level differs in the above 2 situations.

·

During control while a manual shift state is performed (from control start until the accelerator pedal is released), the system informs the driver of the control via the multi-information display and headup display (meter mirror sub-assembly)*.

·

When the VSC OFF switch is operated to turn the TRC off, the system does not operate.

*: Models with headup display (meter mirror sub-assembly)





ii.

Control during Reverse Operation

·

Responds to excessive depression of the accelerator pedal while operating in reverse.

·

Corrects FC system output according to the road grade.

Control Start Conditions (When all of the following conditions are met, control starts.)
·

Shift state is R.

·

Accelerator pedal is depressed excessively.


Control Operation Restricts the FC system output so the vehicle speed and acceleration are at or below a certain level.
Control Stop Conditions
·

Shift state is not R.

·

Accelerator pedal is fully released.



W122966E18
4.375,1.667 4.74,1.667 true 1.771,0.198 2.74,0.406 0.969,0.208 10 false Shift State 1.375,0.552 2.531,0.76 1.156,0.208 10 false Accelerator Pedal 1.885,1.438 2.625,1.802 0.74,0.365 10 false FC System Output 3.677,2.448 4.115,2.656 0.438,0.208 10 false Time 4.771,1.594 5.604,1.802 0.833,0.208 10 false Restricted 2.938,1.031 3.823,1.219 0.885,0.188 10 false Control Starts 2.823,0.208 3.031,0.396 0.208,0.188 10 false R 3.26,0.552 3.469,0.74 0.208,0.188 10 false On 5.26,1.333 6.323,1.552 1.063,0.219 10 false Without Control 5.281,1.979 6.177,2.198 0.896,0.219 10 false With Control





FUNCTION


a.

Driving Mode

i.

The drive mode is changed from NORMAL mode to SPORT mode by pressing the top of the drive mode select switch, and it is changed from NORMAL mode to ECO mode by pressing the bottom of the drive mode select switch.


ii.

If the ignition switch is turned off with "NORMAL" or "ECO" mode selected, the latest mode will be maintained when the ignition switch is turned to ON. However, if "SPORT" mode is selected when the ignition switch is turned off, the drive mode will change to "NORMAL" mode when the ignition switch is turned to ON.

LHD Models
W147902C01
5.375,1.24 5.594,0.792 5.594,0.792 5.792,0.792 true 5.854,0.719 6.167,0.917 0.313,0.198 10 false *1
*1 Drive Mode Select Switch (No. 1 Pattern Select Switch Assembly) - -


RHD Models
W147901C01
5.375,1.24 5.625,0.844 5.625,0.844 5.792,0.844 true 5.833,0.771 6.146,0.969 0.313,0.198 10 false *1
*1 Drive Mode Select Switch (No. 1 Pattern Select Switch Assembly) - -


Motive Force Output Characteristics
W110855E04
3.49,1.115 3,0.406 true 3.917,1.75 3.594,1.417 true 4.948,1.417 4.5,0.979 true 2.51,0.219 4.031,0.479 1.521,0.26 10 false SPORT Mode 1.094,1.25 2.323,1.448 1.229,0.198 10 false Motive force output 3.688,1.813 4.917,2.01 1.229,0.198 10 false NORMAL Mode 4.813,1.458 6.042,1.656 1.229,0.198 10 false ECO Mode 2.906,2.365 4.844,2.625 1.938,0.26 10 false Accelerator pedal opening


iii.

The SNOW mode can be selected by operating the SNOW mode switch.

LHD Models
W147903C01
1.198,1.594 1.427,1.594 1.427,1.594 1.771,1.802 true 4.49,1.625 4.719,1.625 4.719,1.625 4.896,1.854 true 1.021,1.521 1.333,1.677 0.313,0.156 10 false *1 0.125,0.146 0.438,0.302 0.313,0.156 12 false *A: 3.615,0.156 3.927,0.313 0.313,0.156 12 false *B: 4.323,1.552 4.635,1.708 0.313,0.156 10 false *1
*A Models with Advanced Park *B Models without Advanced Park
*1 Snow Mode Switch (Pattern Select Switch Assembly) - -


RHD Models
W147904C01
1.198,1.594 1.427,1.594 1.427,1.594 1.771,1.802 true 4.49,1.625 4.719,1.625 4.719,1.625 4.896,1.854 true 1.01,1.51 1.323,1.667 0.313,0.156 10 false *1 0.125,0.146 0.438,0.302 0.313,0.156 12 false *A: 3.615,0.156 3.927,0.313 0.313,0.156 12 false *B: 4.323,1.542 4.635,1.698 0.313,0.156 10 false *1
*A Models with Advanced Park *B Models without Advanced Park
*1 Snow Mode Switch (Pattern Select Switch Assembly) - -



iv.

When driving without depressing the accelerator pedal, operating the shift lever to Br mode will activate both the regenerative and hydraulic brakes, generating stronger deceleration force than when the shift lever is in D. Depressing the accelerator pedal or operating the shift lever to D will return to normal driving mode.


v.

To display the driving mode selection status, driving mode indicator lights are provided in the combination meter assembly.

Mode Characteristics
Driving Mode Control Characteristics
NORMAL Mode Control is optimized for ease of driving.
ECO Mode The amount of driving force generated in response to accelerator pedal angle is controlled for a milder response, and air conditioner control is changed to give priority to fuel efficiency, with the overall control objective of more fuel-efficient driving.
SPORT Mode At intermediate accelerator opening angles, the power output response is greater than in normal mode, improving accelerator responsiveness.
SNOW Mode Drive force is controlled to improve operability in response to the driver operating the accelerator pedal, such as when driving on a slippery surface.
Br Mode The regenerative brakes and hydraulic brakes are operated to generate stronger deceleration than when the shift lever is in D.