Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
NM37H0E _51 Engine / Hybrid System _097147 HYBRID / BATTERY CONTROL _0466531 HYBRID CONTROL SYSTEM DE DETAILS F

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  DETAILS  INVERTER WITH CONVERTER  


CONSTRUCTION


a.

The MG ECU, inverter, boost converter, and DC-DC converter are combined into a single body, the compact and lightweight inverter with converter assembly. The inverter and boost converter are mainly composed of the Intelligent Power Modules (IPMs) that handle vehicle driving, FC air compressor motor driving, electrical generation and voltage boosting, and also the reactor and capacitor.


b.

The MG ECU controls the inverter and boost converter according to output request values from the EV control ECU.


c.

The boost converter boosts the EV supply battery assembly voltage from DC 310.8 V to a maximum of DC 650 V. In this way, the FC air compressor motor and the electric motor (traction motor) are driven at high voltage, providing higher output power and reducing electrical losses.


d.

The inverter takes the high voltage DC current boosted by the boost converter and the high voltage DC current from the FC stack and changes it to AC current to supply the FC air compressor motor and the electric motor (traction motor). Also, when the electric motor (traction motor) is used as a generator, it changes the generated AC current to DC current.


e.

To optimally control the inverter and boost converter, the inverter with converter assembly contains a number of sensors such as the inverter current sensor, inverter temperature sensor and atmospheric pressure sensor.


f.

The DC-DC converter steps down the EV supply battery assembly voltage from DC 310.8 V to approximately DC 14 V to supply to the auxiliary battery and auxiliary components.


g.

In consideration of safety, interlock switches are provided for the inverter with converter assembly. The interlock switches turn off the SMRs when the inverter terminal cover or connector cover assembly is removed or the connector of the power cable is disconnected.


h.

The inverter with converter assembly includes the EV cooling system, which is independent from the FC cooling system. The coolant directly cools the IPMs that handles vehicle driving, FC air compressor with motor driving, electrical generation and voltage boosting, providing a high level of heat dissipation when the system is in operation, and contributing to the compactness of the inverter with converter assembly.

LHD Models
W147884C01
3.667,2.271 2.708,1.771 2.708,1.771 3.625,2.656 true 1.646,3.708 0.896,3.854 0.896,3.854 1.896,3.427 true 5.24,2.115 5.479,1.635 5.479,1.635 5.729,1.635 true 0.865,1.948 1.125,1.948 1.125,1.948 1.583,2.479 true 0.719,2.448 0.979,2.448 0.979,2.448 1.667,2.708 true 3.667,1.115 4.281,0.885 4.281,0.885 4.531,0.885 true 0.979,4.438 1.24,4.438 1.24,4.438 1.833,3.906 true 2.833,0.49 3.094,0.49 3.094,0.49 3.563,0.854 true 0.698,1.865 1.01,2.021 0.313,0.156 10 false *1 0.552,2.365 0.865,2.521 0.313,0.156 10 false *2 0.813,4.365 1.125,4.521 0.313,0.156 10 false *3 5.771,1.563 6.083,1.719 0.313,0.156 10 false *5 2.271,3.427 2.583,3.583 0.313,0.156 10 false *a 2.531,2.948 2.844,3.104 0.313,0.156 10 false *b 2.656,0.406 2.969,0.563 0.313,0.156 10 false *4 4.594,0.813 4.906,0.969 0.313,0.156 10 false *2 0.719,3.792 1.031,3.948 0.313,0.156 10 false *2 2.563,1.615 2.875,1.771 0.313,0.156 10 false *2
*1 Connector Cover Assembly *2 Interlock Switch
*3 Inverter Hybrid Connector Assembly *4 Inverter Terminal Cover
*5 Inverter with Converter Assembly - -
*a Coolant Inlet *b Coolant Outlet


RHD Models
W147883C01
3.521,2.26 4.469,1.656 4.469,1.656 3.333,2.646 true 5.156,3.448 4.563,4.104 4.563,4.104 5.469,3.635 true 5.542,2.479 5.781,2 5.781,2 6.031,2 true 0.938,1.177 1.198,1.177 1.198,1.177 1.99,1.875 true 2.083,0.802 2.344,0.802 2.344,0.802 3.479,1.188 true 4.208,2.906 4.677,2.208 4.677,2.208 4.927,2.208 true 3.688,0.917 4.302,0.688 4.302,0.688 4.552,0.688 true 5.5,2.708 5.75,3.083 5.75,3.083 6,3.083 true 5.698,3.635 5.948,4.01 5.948,4.01 6.198,4.01 true 0.75,1.115 1.063,1.271 0.313,0.156 10 false *1 1.906,0.729 2.219,0.885 0.313,0.156 10 false *2 4.625,0.635 4.938,0.792 0.313,0.156 10 false *3 6.25,3.948 6.563,4.104 0.313,0.156 10 false *5 4.677,3.354 4.99,3.51 0.313,0.156 10 false *a 4.969,2.125 5.281,2.281 0.313,0.156 10 false *b 6.073,1.927 6.385,2.083 0.313,0.156 10 false *4 4.5,1.531 4.813,1.688 0.313,0.156 10 false *2 6.052,3.042 6.365,3.198 0.313,0.156 10 false *2 4.406,4.083 4.719,4.24 0.313,0.156 10 false *2
*1 Inverter with Converter Assembly *2 Interlock Switch
*3 Inverter Terminal Cover *4 Connector Cover Assembly
*5 Inverter Hybrid Connector Assembly - -
*a Coolant Inlet *b Coolant Outlet


W147921E02
4.083,1.604 4.854,0.865 4.854,0.865 5.115,0.865 true 5.083,2.25 5.51,1.656 5.51,1.656 5.771,1.656 true 4.479,6.854 4.719,6.552 4.719,6.552 4.979,6.552 true 4.948,3.729 5.375,3.135 5.375,3.135 5.635,3.135 true 2.01,1.969 2.073,0.51 2.073,0.51 2.25,0.51 true 0.969,0.448 1.958,0.854 0.99,0.406 10 false Electric Motor (Traction Motor) 3.521,0.344 4.333,0.844 0.813,0.5 10 false FC Air Compressor Motor 5.156,0.771 6.333,1.063 1.177,0.292 10 false Current Sensor 5.823,1.438 6.625,2.302 0.802,0.865 10 false Inverter with Converter Assembly 2.313,0.438 3.281,1.49 0.969,1.052 10 false IPM for Electric Motor (Traction Motor) 2.865,4.115 4.917,4.417 2.052,0.302 10 false IPM for FC Air Compressor Motor 1.198,5.292 2.104,5.583 0.906,0.292 10 false Capacitor 0.438,6.458 1.344,6.75 0.906,0.292 10 false Boost IPM 1.635,6.594 2.542,6.885 0.906,0.292 10 false Reactor 0.375,7.156 1.396,7.458 1.021,0.302 10 false Boost Converter 3.083,5.135 3.99,5.427 0.906,0.292 10 false MG ECU 5.208,5.448 6.219,5.729 1.01,0.281 10 false EV Control ECU 2.958,5.781 4.052,6.125 1.094,0.344 10 false DC-DC Converter 5.052,6.469 6.25,6.875 1.198,0.406 10 false EV Supply Battery Assembly 5.229,7.427 6.75,7.792 1.521,0.365 10 false FC Converter Assembly 5,8.344 6.479,8.656 1.479,0.313 10 false FC Stack Assembly 0.375,8.281 2.51,8.656 2.135,0.375 10 false Compressor with Motor Assembly 5.698,3.042 6.604,3.333 0.906,0.292 10 false Inverter

i.

Inverter

1.

The inverter converts the boosted high-voltage direct current of the EV supply battery assembly into 3 phase alternating current to drive the FC air compressor motor and the electric motor (traction motor).

2.

The activation of the power transistors is controlled by the MG ECU. Additionally, the inverter sends information that is necessary for current control, such as the output amperage and voltage, to the EV control ECU via the MG ECU.

3.

The power transistors used in the inverter are Insulated Gate Bipolar Transistors (IGBTs).



ii.

Boost Converter

1.

The boost converter uses a boost IPM to perform switching control, a reactor to act as an inductor, and a capacitor to accumulate and store electricity. The boost IPM uses IGBT2 for boosting voltage, and IGBT1 for reducing voltage.



iii.

DC-DC Converter

1.

The DC-DC converter steps down the EV supply battery assembly voltage from DC 310.8 V to approximately DC 14 V to supply to the auxiliary battery and auxiliary components.



iv.

MG ECU

1.

The MG ECU is built into the inverter with converter assembly, and following the output request values from the EV control ECU, operates the IPMs that handle vehicle driving, FC air compressor motor driving, electrical generation and voltage boosting, and controls the inverter and boost converter. Also, the MG ECU sends the information necessary for vehicle control, such as the inverter output current value, voltage, inverter with converter assembly internal temperature sensors and atmospheric pressure sensor, to the EV control ECU.

2.

When the MG ECU drives the FC air compressor motor and the electric motor (traction motor), it uses the boost converter to boost the voltage of the DC current from the EV supply battery assembly.

3.

The MG ECU uses the inverter to change DC current into 3 phase AC current, and performs current control. Also, when the electric motor (traction motor) operates as a generator, the AC current generated by the electric motor (traction motor) through regenerative braking is changed to DC current and stepped down to a lower voltage to charge the EV supply battery assembly.

Main Functions of MG ECU
Control Function
Inverter Control FC Air Compressor Motor Control Drives the FC Air Compressor with Motor Assembly according to FC air request values from the FC control ECU.
Electric Motor (Traction Motor) Control
·

Drives the electric motor (traction motor) following output request values from the EV control ECU, which are made according to the torque requested by the driver.

·

Controls the electric motor (traction motor) to function as a generator when there is a regenerative braking request from the No. 2 skid control ECU (brake booster with master cylinder assembly).


Boost Converter Control Boosts the voltage from the EV supply battery assembly from DC 310.8 V to a maximum of DC 650 V and outputs it to the inverter. Also, when the electric motor (traction motor) has generated electricity that has been changed to DC at a maximum of 650 V by the inverter, it is stepped down to DC 310.8 V in order to charge the EV supply battery assembly.



v.

Current Sensor (for Inverter with Converter Assembly)

1.

For the 3-phase AC used to drive the FC air compressor motor and electric motor (traction motor), there are current sensors for the V and W phases. The actual current value is measured and used as feedback by the MG ECU.


Characteristics of Inverter Current Sensor:
W111864E08
0.448,1.26 2.198,1.583 1.75,0.323 10 false Sensor Output Voltage (V) 2.115,1.26 2.729,1.51 0.615,0.25 10 false 5 3.427,2.354 4.24,2.604 0.813,0.25 10 false Current (A) 3.719,2.135 4.333,2.385 0.615,0.25 10 false 0


vi.

Temperature Sensor (for Inverter with Converter Assembly)

1.

For the inverter with converter assembly, there are 5 different temperature sensors; 2 of them are located at the IPMs for FC air compressor motor and the electric motor (traction motor), 2 of them are located at the boost converter, and the remaining sensor is located at the EV coolant passage.

2.

These sensors detect the temperatures at areas inside the inverter with converter assembly, and transmit that temperature information to the EV control ECU via the MG ECU. The EV control ECU optimizes the cooling system according to the temperature information, maintaining the output performance of the inverter with converter assembly.



vii.

Atmospheric Pressure Sensor

1.

The atmospheric pressure sensor is provided on the MG ECU board.

2.

This sensor detects the atmospheric pressure and transmits a signal to the MG ECU to allow corrections that correspond to the usage environment.