Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
NM37H0E _51 Engine / Hybrid System _097147 HYBRID / BATTERY CONTROL _0466531 HYBRID CONTROL SYSTEM DE DETAILS F

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  DETAILS  BOOST CONVERTER  


CONSTRUCTION


a.

An FC boost converter that boosts the output voltage of the FC stack assembly to a maximum of 650 V is used.


b.

The FC boost converter is composed of an FC DC converter control ECU board sub-assembly, FC converter power module transistor (Intelligent Power Module (IPM) for boosting and condenser built-in) and reactors, all of which are built into the FC converter assembly.

W147886C02
2.229,0.24 2.5,0.24 2.5,0.24 2.99,0.792 true 1.646,0.625 1.917,0.625 1.917,0.625 3.094,1.177 true 1.604,2.125 1.875,2.125 1.875,2.125 2.792,1.698 true 2.625,2.51 2.896,2.51 2.896,2.51 3.344,1.969 true 3.729,2.01 5.073,2.448 5.073,2.448 4.031,1.719 true 4.281,1.51 5.635,1.479 5.635,1.479 4.583,1.219 true 2.052,0.167 2.365,0.323 0.313,0.156 10 false *1 1.458,0.552 1.771,0.708 0.313,0.156 10 false *2 1.417,2.052 1.729,2.208 0.313,0.156 10 false *3 2.417,2.448 2.729,2.604 0.313,0.156 10 false *4 5.125,2.448 5.438,2.604 0.313,0.156 10 false *5 5.708,1.417 6.021,1.573 0.313,0.156 10 false *5
*1 FC Converter Assembly *2 FC DC Converter Control ECU Board Sub-assembly
*3 FC Converter Power Module Transistor *4 FC Converter Current Sensor
*5 Reactor - -



c.

The FC DC converter control ECU board sub-assembly operates the boosting IPM to control the FC output current value based on the output request value from the EV control ECU, and boosts the voltage to a maximum of 650 V


d.

The FC converter assembly includes sensors such as the FC converter current sensor.


e.

The FC converter assembly uses coolant to directly cool the boost IPM and reactor.


f.

FC Boost Converter

W147922E02
0.854,0.875 1.052,0.875 1.052,0.875 1.365,1.094 true 1.052,1.563 1.198,1.563 1.198,1.563 1.51,1.781 true 1.094,4.135 1.24,4.135 1.24,4.135 1.906,4.375 true 0.26,4.063 1.104,4.427 0.844,0.365 10 false FC Converter Current Sensor 2.979,0.25 5.146,0.479 2.167,0.229 10 false Inverter with Converter Assembly 0.198,0.823 0.823,1.385 0.625,0.563 10 false FC Boost Converter 0.083,1.51 1.021,2.156 0.938,0.646 10 false FC Converter Power Module Transistor 3.792,1.24 4.917,1.813 1.125,0.573 10 false Capacitor 2.365,5.125 3.49,5.698 1.125,0.573 10 false Reactor 3.438,5.125 4.563,5.698 1.125,0.573 10 false Reactor 4.49,5.115 5.615,5.688 1.125,0.573 10 false Reactor 5.521,5.115 6.646,5.688 1.125,0.573 10 false Reactor 3.51,6.25 4.823,6.5 1.313,0.25 10 false FC Stack Assembly

1.

The FC boost converter consists of 4 phase reactors, MOSFETs, and capacitor.

2.

The ON/OFF operation of the MOSFETs is used to perform FC output power control and voltage boosting. By changing the number of operating MOSFETs based on vehicle conditions, fuel efficiency is improved.



g.

FC Converter Current Sensor

i.

The FC converter current sensor is positioned between the FC converter power module transistor and reactors, and detects each FC output current value. The FC DC converter control ECU board sub-assembly performs feedback control for the on time of the MOSFET, based on this output current value.

Characteristics of Current Sensor:
W111864E10
0.25,1.25 1.958,1.625 1.708,0.375 10 false Sensor Output Voltage (V) 2.021,1.26 2.177,1.51 0.156,0.25 10 false 5 3.427,2.354 4.167,2.667 0.74,0.313 10 false Current (A) 3.719,2.135 3.917,2.333 0.198,0.198 10 false 0



h.

FC DC Converter Control ECU Board Sub-assembly

1.

The FC DC converter control ECU board sub-assembly is located inside the FC converter assembly, and operates the MOSFET according to the output request value from the EV control ECU, and thus controls the output of the boost converter. The FC DC converter control ECU board sub-assembly sends the FC converter input current value, voltage value, and other information necessary for vehicle control to the EV control ECU.


FC DC converter control ECU board sub-assembly Main Controls
Control Function
FC Boost Converter Control Controls the output current of the FC stack assembly while boosting the output voltage to a maximum of DC 650 V to output to the inverter with converter assembly.