Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM › 2020.11–2021.08
NM37H0E _58 Vehicle Interior _097230 THEFT DETERRENT / KEYLESS ENTRY _0455368 ENTRY AND START SYSTEM CO CONTROL F

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM  CONTROL  ENTRY AND START CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components for the entry function have the following functions:

Component Function

*1: Models with panic alarm function

*2: Models with answer back buzzer function

*3: Models with multi-display assembly

*4: Models with radio and display receiver assembly

Electrical Key (Electrical Key Transmitter Sub-assembly)
·

Outputs information such as the key ID and vehicle ID when request signals that are output by the room and door antennas are received.

·

Outputs a request signal when the lock, unlock, panic*1 or power trunk lid open button on the electrical key is pushed.

·

Has an integrated mechanical key that can be used to unlock the doors when the key battery is weak.


Door Control Receiver (Electrical Key and TPMS Receiver Assembly) Receives the ID code from the electrical key and transmits it to the certification ECU.
Multiplex Network Master Switch Assembly
·

Door Control Switch


Outputs door lock/unlock request signals, which are generated by door control switch operations, to the front multiplex network door ECU LH.
Power Window Regulator Switch Assembly
·

Door Control Switch


Outputs door lock/unlock request signals, which are generated by door control switch operations, to the main body ECU.
Front Door Outside Handle Assembly LH Unlock Sensor Detects user entry unlock operations.
Lock Sensor Detects user entry lock operations.
Door Electrical Key Antenna Receives a request signal from the certification ECU and creates an actuation area around the front door LH.
Front Door Outside Handle Assembly RH Unlock Sensor Detects user entry unlock operations.
Lock Sensor Detects user entry lock operations.
Door Electrical Key Antenna Receives a request signal from the certification ECU and creates an actuation area around the front door RH.
No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment) Receives a request signal from the certification ECU and forms an actuation area in the luggage compartment.
Electrical Key Antenna (Outside Luggage Compartment) Receives a request signal from the certification ECU and forms an actuation area around the luggage compartment door.
No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) Receives a request signal from the certification ECU and forms an actuation area in the vehicle.
No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor)
Front Door Lock with Motor Assembly (for Driver Door)
·

Door Lock Motor

·

Door Lock Position Switch

·

Door Lock Control Switch


·

Rotates the built-in door lock motor in the extend and retract directions to lock and unlock the doors.

·

Uses the built-in door lock position switch to detect whether the doors are locked or unlocked and outputs the result to the main body ECU.

·

Detects the condition of the built-in door lock control switch and outputs mechanical key lock/unlock request signals to the main body ECU.


Front Door Lock with Motor Assembly (for Front Passenger Door)
·

Door Lock Motor

·

Door Lock Position Switch


·

Rotates the built-in door lock motor in the extend and retract directions to lock and unlock the doors.

·

Uses the built-in door lock position switch to detect whether the doors are locked or unlocked and outputs the result to the main body ECU.


Rear Door Lock with Motor Assembly LH
·

Door Lock Motor

·

Door Lock Position Switch


·

Rotates the built-in door lock motor in the extend and retract directions to lock and unlock the doors.

·

Uses the built-in door lock position switch to detect whether the doors are locked or unlocked and outputs the result to the main body ECU.


Rear Door Lock with Motor Assembly RH
·

Door Lock Motor

·

Door Lock Position Switch


·

Rotates the built-in door lock motor in the extend and retract directions to lock and unlock the doors.

·

Uses the built-in door lock position switch to detect whether the doors are locked or unlocked and outputs the result to the main body ECU.


Luggage Compartment Door Lock Assembly Luggage Door Lock Motor When the TRUNK OPEN relay is turned on via main body ECU control, the luggage door lock motor runs and opens the luggage compartment door.
Luggage Door Courtesy Switch The built-in luggage door courtesy switch detects whether the luggage compartment door is open or closed and outputs this information to the main body ECU.
Luggage Room Relay Block Assembly
·

TRUNK OPEN Relay


Inputs luggage compartment door open request signals from the main body ECU and operates the luggage door motor.
Instrument Panel Junction Block Assembly ADD DR LOCK Relay Inputs door lock request signals from the main body ECU and operates the door lock motor of all doors.
D DR UNLOCK Relay Inputs driver door unlock request signals from the main body ECU and operates the driver door lock motor.
L/D DR UNLOCK Relay Inputs passenger door unlock request signals from the main body ECU and operates the door lock motors at the front passenger seat and rear seats.
Front Door Courtesy Light Switch Assembly (LH) Outputs open/close signals for front door LH to the main body ECU.
Front Door Courtesy Light Switch Assembly (RH) Outputs open/close signals for front door RH to the main body ECU.
Rear Door Courtesy Light Switch Assembly (LH) Outputs open/close signals for rear door LH to the main body ECU.
Rear Door Courtesy Light Switch Assembly (RH) Outputs open/close signals for rear door RH to the main body ECU.
Hood Lock Assembly
·

Hood Courtesy Switch


Outputs open/close signals for engine hood to the main body ECU.
Luggage Door Opening Cancel Switch Assembly Cancels the luggage compartment door open operation when the switch is turned off (switch is not pressed).
Luggage Electrical Key Switch Transmits a luggage compartment door open request signal to the certification ECU.
Wireless Door Lock Buzzer
·

Sounds as an answer back for entry lock/unlock and wireless lock/unlock to inform the driver.*2

·

Sounds to inform the driver of malfunctions in the entry and start system.


Certification ECU (Smart Key ECU Assembly)
·

Detects the vehicle condition using ECU and switch signals and performs entry and start system control.

·

Controls the electrical key antennas and forms detection areas.

·

Transmits the door lock/unlock request signals during the entry function.

·

Sends wireless door lock control signals that are input from the door control receiver to the main body ECU.

·

Sends warning request signals to the main body ECU or combination meter assembly when warning conditions are met.


Main Body ECU (Multiplex Network Body ECU)
·

Sends signals such as the door courtesy light switch and door lock position switch signals to the certification ECU and other parts via CAN communication.

·

Checks whether all door lock/unlock operations are complete, sends hazard warning light operation signals to the combination meter assembly, outputs sounding request signals to the wireless door lock buzzer*2 and performs answer back operations.

·

Receives warning request signals from the certification ECU and outputs sounding request signals to the wireless door lock buzzer when warning conditions are met.

·

Receives ECU and switch signals, outputs lock/unlock signals to the door lock with motor assemblies and operates the door lock motor.

·

Receives luggage compartment door open request signals from each ECU and switch, and turns the TRUNK OPEN relay on.


EV Control ECU Sends shift position signals and brake pedal operation signals to the main body ECU.
Shift Control ECU Sends shift position P signals to the certification ECU.
Brake Actuator Assembly
·

No. 2 Skid Control ECU


Sends vehicle speed signals to the main body ECU.
Radio Receiver Assembly*3 Sends customization information that was set through the multi-display to the main body ECU.
Integration Control Sub-Assembly*3 Sends function customization information from the multi-display assembly setting screen to the radio receiver assembly.
Multi-display Assembly*3 Displays the settings screen.
Radio and Display Receiver Assembly*4 Sends function customization information from the multi-display assembly setting screen to the main body ECU.
Combination Meter Assembly
·

Displays the entry unlock mode condition.

·

Flashes the hazard warning lights when an answer back operation is performed.

·

Sends vehicle speed signals to the certification ECU.

·

Displays a warning message on the multi-information display when a power source state or system malfunction occurs.

·

Displays a message on the multi-information display when a malfunction occurs in the entry and start system.


Central Gateway ECU (Network Gateway ECU) Relays the signal between the CAN communication lines.
DLC3
·

Can read the Diagnostic Trouble Codes (DTCs) of malfunctions by connecting the Global TechStream (GTS).

·

The Global TechStream (GTS) can be connected to change settings as desired by the user.




b.

The main components for the start function have the following functions:

Component Function

*1: Models with multi-display assembly

*2: Models with radio and display receiver assembly

Electrical Key (Electrical Key Transmitter Sub-assembly)
·

Outputs information such as the key ID and vehicle ID when request signals that are output by the room and door antennas are received.

·

Outputs information such as the key ID and vehicle ID when the radio wave signal that is output by the transponder key amplifier in the power switch is received.


Door Control Receiver (Electrical Key and TPMS Receiver Assembly) Receives electrical wave responses generated in the detection area and electrical waves transmitted using the wireless remote control, and outputs them to the certification ECU.
No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment) Receives a request signal from the certification ECU and forms an actuation area in the luggage compartment.
Electrical Key Antenna (Outside Luggage Compartment) Receives a request signal from the certification ECU and forms an actuation area around the luggage compartment door.
No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) Transmits electrical waves inside the cabin to determine whether the electrical key is within the detection area in the cabin.
No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor)
Power Switch (Push Start Switch)
·

A switch for turning on the power source and starting the fuel cell system.

·

The built-in immobilizer amplifier starts the fuel cell system if the electrical key does not operate normally due to a depleted key battery or radio wave interference.


Stop Light Switch Assembly Outputs the state of the brake pedal to the certification ECU.
Multi-display Assembly*1
·

Security Indicator Light


Flashes when the immobiliser system is set according to certification ECU control.
Telltale Light Assembly*2
·

Security Indicator Light


Certification ECU (Smart Key ECU Assembly)
·

Detects the vehicle condition using ECU and switch signals and performs entry and start system control.

·

Controls the electrical key antennas and forms detection areas.

·

Transmits the steering wheel lock/unlock signals.

·

Outputs immobiliser system set and unset commands to the ID code box.

·

Judges and certifies the electrical key.

·

Controls the security indicator light operation, power source state display (ACCESSORY and IGNITION ON) and key certification indicator display.

·

Sends warning request signals to the main body ECU or combination meter assembly when warning conditions are met.

·

Operates parts such as the IG1 relay and ACC relay and controls the power source change condition.

·

Sends fuel cell system start permission signals to the EV Control ECU.


EV Control ECU
·

Receives fuel cell system start permission signals from the certification ECU and starts the fuel cell system.

·

Sends shift position signals and brake pedal operation signals to the main body ECU.


Shift Control ECU Sends shift position P signals to the certification ECU.
Brake Actuator Assembly
·

No. 2 Skid Control ECU


Sends vehicle speed signals to the main body ECU.
Steering Lock Actuator Assembly
·

Steering Lock ECU


Receives the steering wheel unlock/lock request signal from the certification ECU, and activates the steering lock motor.
ID Code Box (Immobiliser Code ECU) Receives immobiliser system set or unset command signals from the certification ECU and sends immobiliser system set or unset command signals to the EV control ECU.
Combination Meter Assembly
·

Provides warnings (multi-information display and meter buzzer sounds) according to operation command signals from the certification ECU.

·

Sends vehicle speed signals to the certification ECU.

·

Displays a warning message on the multi-information display when a power source state or system malfunction occurs.


Central Gateway ECU (Network Gateway ECU) Relays the signal between the CAN communication lines.
DLC3
·

Can read the Diagnostic Trouble Codes (DTCs) of malfunctions by connecting the Global TechStream (GTS).

·

The Global TechStream (GTS) can be connected to change settings as desired by the user.





OPERATION


a.

The special functions of the entry and start system only work when the electrical key is in the actuation area formed by the antennas.


b.

The No. 1 and No. 2 indoor electrical key antenna assemblies form the actuation area of the start function.


c.

The No. 3 indoor electrical key antenna assembly form the inside luggage compartment actuation area.


d.

The door electrical key antennas form the actuation area of the entry function.


e.

The electrical key antenna form the actuation area of the luggage compartment door open function.

Y269878C01
0.896,0.958 3.094,2.875 true 3.188,0.823 3.219,2.073 true 6.708,2.844 5.448,2.896 true 5.094,4.844 3.781,2.917 true 6.24,4.781 4.813,2.896 true 3.25,4.938 3.208,3.729 true 0.719,0.833 1.031,0.99 0.313,0.156 10 false *1 3.219,5 3.531,5.156 0.313,0.156 10 false *2 5.135,4.896 5.448,5.052 0.313,0.156 10 false *3 6.271,4.823 6.583,4.979 0.313,0.156 10 false *4 6.75,2.781 7.063,2.938 0.313,0.156 10 false *5 3.094,0.635 3.406,0.792 0.313,0.156 10 false *6
*1 No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) *2 Front Door Outside Handle Assembly LH
·

Door Electrical Key Antenna


*3 No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor) *4 No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment)
*5 Electrical Key Antenna (Outside Luggage Compartment) *6 Front Door Outside Handle Assembly RH
·

Door Electrical Key Antenna


V100144

Exterior Actuation Area
V100145

Interior Actuation Area
V100146

Outside Luggage Compartment Door Actuation Area
V100155

Inside Luggage Compartment Door Actuation Area


Actuation Area Detail
Interior The interior actuation area of the indoor electrical key antennas (front, rear) is formed when the driver door is opened or closed, when the power switch is pushed, when a warning is activated, or when an entry lock operation is performed.
Inside Luggage Compartment The inside luggage compartment actuation area is formed when the luggage compartment door is closed after the doors are locked or before any doors are opened after the doors are unlocked.
Exterior The exterior actuation area formed by the door electrical key antennas (Front LH, Front RH) and outside electrical key antenna is approximately 0.7 to 1.0 m (2.3 to 3.3 ft.) from the door outside handle assembly or the center of the rear bumper.
Around Front Doors The exterior actuation area of the door electrical key antennas is formed by transmitting a request signal every 0.25 seconds while the power source is off and each door is locked. In this way, it detects the presence of an electrical key. When a door is locked by an entry lock operation, the actuation area is formed.
Around Luggage Compartment Door The exterior actuation area of the electrical key antenna is formed when all the doors are locked and the luggage electrical key switch is on.



FUNCTION


a.

The entry and start system consists of the following functions:

Function Outline
Entry Unlock When the user carries the electrical key and touches the unlock sensor of the door outside handle (or grabs the door outside handle), the doors can be unlocked.
·

Only the driver door is unlocked when the unlock sensor of the driver door outside handle is touched. (Driver Door Unlock Mode)

·

All the doors unlock when the unlock sensor of the driver door outside handle is touched. (All Door Unlock Mode)

·

All the doors unlock when the unlock sensor of the front passenger door outside handle is touched.


Entry Unlock Mode Switching*1 Allows switching between 2 modes that can be operated with the entry unlock function.
·

Driver Door Unlock Mode

·

All Door Unlock Mode


Entry Lock When the user carries the electrical key and touches any lock sensor of the door outside handles, all the doors can be locked.
Luggage Compartment Door Open Function When an electrical key is in the exterior actuation area of the outside electrical key antenna (luggage compartment door), the luggage compartment door opens manually by simply pushing the luggage electrical key switch.
Start Changes the power source or starts the fuel cell system.
Answer Back When the doors are being locked or unlocked using the electrical key, the wireless door lock buzzer sounds*2 and the hazard warning lights blink once while locking and twice while unlocking. Also, the answer back function operates when the doors are locked by the automatic relock function.
Door Open Operation Prohibition Prohibits the use of entry lock operations to lock the door when any door is ajar or open.
Warning When the user attempts to turn off the power source mode with the shift position not in P while touching the lock sensor of the door outside handle with the electrical key in the cabin, the wireless door lock buzzer sounds and a warning message is displayed on the multi-information display to warn the driver.
Prevention of Key Confinement Prevents the vehicle from being locked with an electrical key left inside it. This function operates in 2 different situations: when the lock button on the door control switch is used (keyless lock) and when an entry lock operation is performed to lock the vehicle. (Does not operate when the electrical key is in the sleep state.)
Prevention of Key Confinement into Luggage Compartment Allows the luggage electrical key switch to be pressed and used to open the luggage compartment door when the luggage compartment door is closed with the electrical key inside the luggage compartment, even though the luggage compartment door cannot normally be opened in that condition. (Does not operate when the electrical key is in the sleep state.)
Battery Saving
·

Suppresses auxiliary battery level drops when the vehicle is not used for a long period of time by extending the interval between or stopping each periodic transmission of the request signal and restricting the entry function.

·

When the electrical key is in an exterior actuation area for approximately 10 minutes or more, periodic transmission of the request signal is stopped to suppress key battery level drops.

·

Puts the electrical key in the sleep condition to suppress key battery level drops.*3

·

When the unlock button is pressed 2 times while pressing the lock button of the electrical key, the electrical key stops waiting on standby to receive electrical waves, suppressing key battery level drops.


Key Cancel The following key functions can be canceled by following the specified procedure.
·

Entry unlock/lock

·

Power trunk lid open

·

Prevention of key confinement

·

Warning


Automatic Relock If none of the doors are opened within 30 seconds after they are unlocked using the wireless door lock remote control, all the doors will be locked again automatically.
Security Sends a door lock/unlock operation request signal as a rolling code.
Immobiliser Only permits electrical key registered with the vehicle to start the fuel cell system, preventing unauthorized starting of the system.
Key Code Registration A total of 7 electrical key can be registered.
Customization Allows the user to change settings as desired. Refer to the Repair Manual for details.

HINT:

*1: Initialization settings vary depending on the model.

*2: Models with answer back buzzer function

*3: If the electrical key is not operated for a certain amount of time, it is temporarily stopped to reduce power consumption. In this case, verification required for power source mode change, etc. cannot be performed. The electrical key will automatically return from the lower power consumption state if its position is moved while being held.




SYSTEM CONTROL


a.

Entry Unlock Function

i.

When the user carries the electrical key in the exterior actuation area and grabs the driver door outside handle (touches the unlock sensor), only the driver door unlocks. (Driver door mode)


ii.

When the user carries the electrical key in the exterior actuation area and grabs the driver door outside handle (touches the unlock sensor), all the doors unlock. (All door unlock mode)


iii.

When the user carries the electrical key in the exterior actuation area and grabs the front passenger door outside handle (touches the unlock sensor), all the doors unlock.


iv.

When the doors are unlocked, the hazard warning lights flash twice and the buzzer sounds twice* as an answer back.

*: Models with answer back buzzer function


HINT:

If the doors are locked by wireless operation, the entry and start system or key linked power door lock operation, it may not be possible to unlock the doors using the entry and start system. In this situation, use the wireless function of the electrical key to unlock the doors.


NOTICE:
·

When the user quickly performs an unlock operation or abruptly enters the exterior actuation area to perform an unlock operation and is unable to unlock the doors, an unlock operation needs to be performed again. When an unlock operation is performed while wearing gloves, the door may not unlock.

·

If another electrical key is in the exterior actuation area, the time it takes to unlock the door(s) after the unlock operation may be slightly longer than usual.

·

After the doors are locked, the doors cannot be unlocked for approximately 3 seconds.

·

After unlocking using the mechanical key, entry unlock function cannot be performed using door outside handle operation. To unlock, either perform a wireless operation or operate the door control switch. Entry unlock function can be used by either performing another lock operation or starting the fuel cell system.

·

When a wireless door lock, manual door lock or key-linked door lock operation is performed with an electrical key in the interior actuation area or near the vehicle, the entry unlock function may not operate. In this case, it is possible to unlock the doors by performing a wireless door unlock operation.



Y176307C02
3.781,1.031 4.333,1.333 4.333,1.333 4.583,1.333 true 4.667,1.26 4.833,1.417 0.167,0.156 10 true *1
*1 Unlock Sensor - -




b.

Entry Lock Function

i.

When the user carries the electrical key, exits the vehicle and touches the lock sensor on the surface of the front door outside handle in the exterior actuation area with all the doors closed, all the doors lock.


ii.

When the doors are locked, the hazard warning lights flash once and the buzzer sounds once* as an answer back.

*: Models with answer back buzzer function


Y176308C02
2.229,0.333 2.5,0.333 2.5,0.333 3.406,1.156 true 2.021,0.25 2.167,0.417 0.146,0.167 10 true *1
*1 Lock Sensor - -




c.

Luggage Compartment Door Open Function

i.

When the doors are locked, the luggage compartment door can be opened by pressing the luggage electrical key switch while the user is carrying the electrical key within the luggage compartment door exterior actuation area.

Y269746C02
4.417,4.26 4.292,2.99 true 4.365,4.292 4.677,4.448 0.313,0.156 10 false *1
*1 Luggage Electrical Key Switch - -
V100135

Press Luggage Electrical Key Switch - -




d.

Start Function

i.

The start function has different power source change patterns to suit the brake pedal state and shift position.

Pattern Brake Pedal Shift Position Power Source Change Pattern
A Depressed P When the power switch is pushed once.
·

Off → READY


B Not Depressed P Each time the power switch is pushed.
·

Off → On (ACC) → On (IG) → Off


C Except P Each time the power switch is pushed.
·

On (ACC) → On (IG) → Off


D - P When the power switch is pushed in the on (IG) condition.
·

On (IG) (fuel cell system is started or not started) → Off


E - Except P When the power switch is pushed in the on (IG) condition.
·

On (IG) (fuel cell system is started or not started) → Off



Transition of Power Source Modes
Y214545E02
0.479,0.542 1.646,0.844 1.167,0.302 10 false Shift Position 3.771,0.573 4.292,0.875 0.521,0.302 10 false P 6.167,0.563 7.073,0.896 0.906,0.333 10 false Except P 0.625,0.969 1.792,1.271 1.167,0.302 10 false Pattern 0.49,1.365 1.656,1.667 1.167,0.302 10 false Power Switch 0.5,1.75 1.667,2.052 1.167,0.302 10 false Brake Pedal 0.688,2.167 1.125,2.479 0.438,0.313 10 false Time 0.271,3.135 0.813,3.76 0.542,0.625 10 false Power Source 1.208,2.552 1.677,2.896 0.469,0.344 10 false Off 1.021,2.969 1.729,3.323 0.708,0.354 10 false On (ACC) 1.063,3.375 1.771,3.729 0.708,0.354 10 false On (IG) 1.073,3.76 1.781,4.115 0.708,0.354 10 false READY 2.219,2.167 2.656,2.479 0.438,0.313 10 false - 3.552,2.156 3.99,2.469 0.438,0.313 10 false - 6.469,2.188 6.906,2.5 0.438,0.313 10 false - 2.219,1.75 2.656,2.063 0.438,0.313 10 false - 5.104,1.74 5.542,2.052 0.438,0.313 10 false - 5.094,1.333 5.531,1.646 0.438,0.313 10 false - 5.083,0.938 5.521,1.25 0.438,0.313 10 false - 6.458,1.76 6.896,2.073 0.438,0.313 10 false - 2.052,1.354 2.667,1.667 0.615,0.313 10 false Pushed 3.333,1.354 3.948,1.667 0.615,0.313 10 false Pushed 6.25,1.344 6.865,1.656 0.615,0.313 10 false Pushed 3.25,1.76 4.094,2.073 0.844,0.313 10 false Depressed 4.5,2.24 4.781,2.563 0.281,0.323 10 false *1 5.063,2.24 5.344,2.563 0.281,0.323 10 false *2 5.594,2.24 5.875,2.563 0.281,0.323 10 false *3 0.615,4.365 1.74,4.698 1.125,0.333 10 false : Transition 0.594,4.75 3.729,5.073 3.135,0.323 10 false : Only when key certification is OK. 0.625,5.146 6.552,5.875 5.927,0.729 10 false : Only when the vehicle is stopped. (While driving, if the power switch is pressed for 2 seconds or more or pressed 3 times or more in a row, the fuel cell system is stopped and the power source mode changes to on (ACC).) 3.385,0.969 4,1.281 0.615,0.313 10 false A or D 2.083,0.958 2.698,1.271 0.615,0.313 10 false B or D 6.302,0.948 6.917,1.26 0.615,0.313 10 false C or E 0.188,6.781 2.656,7.135 2.469,0.354 10 false *1: Not operated for 20 minutes 0.188,7.146 2.583,7.5 2.396,0.354 10 false *2: Not operated for 1 hour 0.198,7.542 5.188,7.854 4.99,0.313 10 false *3: Power source turned off according to fuel cell system request 0.646,6.083 6.625,6.583 5.979,0.5 10 false : Only when the vehicle is stopped. (The power switch is turned off after the shift position is changed to P by the automatic P position switch function.)

NOTICE:
·

Normally, the operation of the power switch is disabled while the vehicle is being driven. However, in an emergency, by pushing the power switch for approximately 2 seconds or more or pushing the power switch 3 times or more in a row, the driver can stop the fuel cell system while the vehicle is in motion.

·

If no signals are transmitted to the certification ECU due to malfunctions in the stop light switch assembly, the fuel cell system may not start when the power switch is pushed with the brake pedal depressed. In such cases, performing the following procedure may enable the fuel cell system to start: 1) push the power switch to turn the power source from off to on (ACC), and 2) push the power switch again and hold it for 15 seconds or more.

·

The above 2 operations must be applied only in emergency situations. Under normal conditions, the fuel cell system must not be stopped by pushing the power switch while driving. Also, it should not be started without depressing the brake pedal or when a shift position other than P has been changed.





e.

Warning Function

i.

When any of the situations below occur, the entry and start system sounds the wireless door lock buzzer* and a buzzer in the combination meter assembly and displays a message on the multi-information display in order to alert the driver

*: Models with answer back buzzer function


Situation Condition
A The fuel cell system is left running and the shift position is not P when the driver gets out of the vehicle.
B The fuel cell system is left running and the shift position is P when the driver gets out of the vehicle.
C The fuel cell system is left running when a passenger gets out of the vehicle while holding the electrical key.
D The electrical key is not within the actuation areas.
E The vehicle is driven without an electrical key.
F The electrical key is left in the vehicle.
G A door is ajar.
H The vehicle has started off with an electrical key in the luggage compartment.
I The key reminder sounds.
J The key battery is weak.
K Steering lock does not release.
L A malfunction has been detected in a vehicle speed signal, etc.
M The fuel cell system cannot be started (system/driver error).
N Immobiliser system certification confirmation occurs.
O An electrical key has been registered to the vehicle.
P Fuel cell system start operation guide on (ACC)
Q The power source cannot be turned off (shift lever in any position except P).
R The power source cannot be turned off (shift lever in P).
S Fuel cell system start operation guide on (IG)
T Auto power off operation occurs.
U Fuel cell system emergency stop operation is performed.
V The user performed an emergency engine stop while driving.
W Power switch is operated while driving.
X Power switch is operated while driving.
Y While the vehicle is stationary, with a shift state other than park (P) or neutral (N) selected, the power source on (IG) and the fuel cell system stopped.
Z While the vehicle is stationary, with a shift state neutral (N) selected, the power source on (IG) and the fuel cell system stopped.
AA The vehicle started to roll away with the power source on (IG) and the fuel cell system stopped.
AB Accessory state
AC Ignition on state


ii.

Situation A

There are 2 patterns for situation A.

Pattern 1:

When the shift position is not P, the power source is in a mode other than off and the driver opens the door and attempts to get out of the vehicle, the following control is performed.

Possible Effects without Warning Sudden vehicle movement, vehicle theft, vehicle roll-away (vehicle creep, such as when N is selected)
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power source is on (ACC) or on (IG).

·

The shift position is not P.

·

The driver door is opened.

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Multi Buzzer Sounds continuously
Multi-information Display The following warning message is displayed:
·

Shift to P Before Exiting Vehicle


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The power source is turned off.

·

The shift position is changed to P.

·

The driver door is closed.

·

The vehicle speed is above 5 km/h (3 mph).



Pattern 2:

Under the situation of pattern 1, the driver closes the door and attempts to leave the vehicle while holding the electrical key. In this situation, the following control is performed:

Possible Effects without Warning Sudden vehicle movement, vehicle theft, vehicle roll-away

*: Models with answer back buzzer function

Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power source is on (ACC) or on (IG).

·

The shift position is not P.

·

The driver door is opened → closed.

·

The electrical key is not detected in the vehicle (interior key certification fails).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Multi Buzzer Sounds continuously
Multi-information Display The following warning messages are alternately displayed:
·

Shift to P Before Exiting Vehicle

·

Key Not Detected Check Key Location


Advisory Display -
Wireless Door Lock Buzzer Sounds continuously*
Buzzer and Wireless Door Lock Buzzer* Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The power source is turned off.

·

The shift position is changed to P.

·

The vehicle speed is above 5 km/h (3 mph).

·

The electrical key is detected in the vehicle (interior key certification result is OK).


"Shift to P Before Exiting Vehicle" Message Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The shift position is changed to P.

·

The vehicle speed is above 5 km/h (3 mph).


"Key Not Detected Check Key Location" Message Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The power source is turned off.

·

The electrical key is detected in the vehicle (interior key certification result is OK).





iii.

Situation B

There are 3 patterns for situation B.

Pattern 1:

When the shift position is P and the power source is in a mode other than off (the steering remains unlocked), the driver door is opened and the driver attempts to leave the vehicle. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft
Warning Active Condition Condition 1
The warning is activated when both of the following conditions are met:
·

The power source is on (ACC).

·

The remote air conditioning system is off.

·

The driver door is open.


Condition 2
The warning is activated when all of the following conditions are met for 1 second:
·

The power source is turned off.

·

The remote air conditioning system is off.

·

The steering lock remains unlocked.

·

The driver door is open.


Warning Method Combination Meter Assembly Multi Buzzer Sounds continuously at short and even intervals
Multi-information Display -
Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The power source is turned on (IG).

·

The remote air conditioning system is on.

·

The driver door is closed.

·

The power source is turned off and the steering wheel lock control is performed.



Pattern 2:

Under the situation of pattern 1, the driver opens and closes the driver door and attempts to leave the vehicle while holding the electrical key. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft

*: Models with answer back buzzer function

Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power source is on (ACC) or on (IG).

·

The shift position is P.

·

The driver door is opened → closed.

·

The electrical key is not detected in the vehicle (interior key certification fails).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Key Not Detected Check Key Location


Advisory Display -
Wireless Door Lock Buzzer Sounds 3 times*
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The power source is turned off.

·

The electrical key is detected in the vehicle (interior key certification result is OK).



Pattern 3:

Under the situation of pattern 2, the driver performs an entry lock operation. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft

*: Models with answer back buzzer function

Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power source is on (ACC) or on (IG).

·

The shift position is P.

·

The electrical key is not detected in the vehicle (interior key certification fails), but detected in an outside detection area (exterior key certification result is OK).

·

The lock sensor on the door outside handle is on (touched).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning messages are alternately displayed:
·

Turn Power Off

·

Key Not Detected Check Key Location


Advisory Display -
Wireless Door Lock Buzzer Sounds continuously*
Wireless Door Lock Buzzer Warning Stop Condition* The warning is stopped when one of the following conditions is met:
·

5 seconds elapse.

·

The power source is turned off.

·

The shift position is changed to a position other than P.

·

The vehicle speed is above 5 km/h (3 mph).

·

The electrical key is detected in the vehicle (interior key certification result is OK).

·

Any door is opened or closed.


"Turn Power Off" Message Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

60 seconds elapse.

·

The power source is turned off.

·

The shift position is changed to a position other than P.

·

The vehicle speed is above 5 km/h (3 mph).


"Key Not Detected Check Key Location" Message Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The power source is turned off.

·

The electrical key is detected in the vehicle (interior key certification result is OK).





iv.

Situation C

When the fuel cell system is left running, a passenger leaves the vehicle while holding the electrical key. In this situation, the following control is performed:

Possible Effects without Warning Fuel cell system cannot be restarted.

*: Models with answer back buzzer function

Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power source is on (ACC) or on (IG).

·

A door other than the driver door is opened → closed (does not include luggage compartment door).

·

The electrical key is not detected in the vehicle (interior key certification fails).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Key Not Detected Check Key Location


Advisory Display -
Wireless Door Lock Buzzer Sounds 3 times*
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The power source is turned off.

·

The electrical key is detected in the vehicle (interior key certification result is OK).





v.

Situation D

When the electrical key is not in the vehicle, the driver attempts to turn the power source on (IG) (emergency key operation* is included). In this situation, the following control is performed:

Possible Effects without Warning User becomes confused

*: Emergency key operation is an operation that changes the power source by touching the power switch with the electrical key.

Warning Active Condition The warning is activated when all of the following conditions are met:
·

The immobiliser system is set.

·

The electrical key is not in the vehicle (interior key certification fails and transponder certification fails).

·

No records of unlock operation using a mechanical key and key certification failure when the power source was turned on (IG).


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Key Not Detected Check Key Location


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

15 seconds elapse.

·

The electrical key is detected in the vehicle (interior key certification result is OK and transponder certification result is OK).

·

30 seconds have elapsed since a door was opened using a door outside handle.





vi.

Situation E

The vehicle starts moving without a registered electrical key in the vehicle. In this situation, the following control is performed:

Possible Effects without Warning Fuel cell system cannot be restarted.
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power source is on (IG).

·

The warning is activated in situation C.

·

The vehicle speed is above 5 km/h (3 mph).

·

The electrical key is not detected in the vehicle (interior key certification fails).


Warning Method Combination Meter Assembly Multi Buzzer Sounds 9 times
Multi-information Display The following warning message is displayed:
·

Key Not Detected Check Key Location


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The power source is turned off.

·

The electrical key is detected in the vehicle (interior key certification result is OK).





vii.

Situation F

The driver exits the vehicle while leaving the electrical key inside the vehicle and performs an entry lock operation. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft

*: Models with answer back buzzer function

Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power source is off.

·

All doors are closed.

·

The electrical key is detected in the vehicle (interior key certification result is OK).

·

The lock sensor on the door outside handle is on (touched).

·

Any door is unlocked.

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Key Detected in Vehicle


Advisory Display -
Wireless Door Lock Buzzer Sounds continuously*
Wireless Door Lock Buzzer Warning Stop Condition The warning is stopped when any of the following conditions is met:
·

5 seconds elapse.

·

The power source is turned on (ACC) or on (IG).

·

The vehicle speed is above 5 km/h (3 mph).

·

Any door is opened.

·

Lock operation is detected.


"Key Detected in Vehicle" Message Warning Stop Condition The warning is stopped when any of the following conditions is met:
·

60 seconds elapse.

·

The power source is turned on (ACC) or on (IG).

·

The vehicle speed is above 5 km/h (3 mph).

·

Lock operation is detected.





viii.

Situation G

The driver performs an entry lock operation while any door is ajar. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft

*: Models with answer back buzzer function

Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power source is off.

·

Any door is open other than the door where the entry lock operation is performed.

·

The lock sensor on the door outside handle is on (touched), the lock button on the electrical key.

·

The electrical key is in an outside detection area (exterior key certification result is OK).


Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display -
Advisory Display -
Wireless Door Lock Buzzer Sounds continuously*
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

5 seconds elapse.

·

The power source is turned on (ACC) or on (IG).

·

All doors are closed.

·

Unlock operation is performed using the wireless door lock remote function.

·

Unlock operation is performed using the touch sensor on the inside of an outer door handle.

·

Any of the doors are open.





ix.

Situation H

The luggage compartment door is closed with the electrical key left in the luggage compartment.

In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft

*: Models with answer back buzzer function

Warning Active Condition The warning is activated when all of the following conditions are met:
·

The vehicle speed is not detected.

·

The entry luggage compartment door open function is available.

·

All doors are closed and locked, or after unlocking, before a door is opened.

·

The luggage compartment door is opened → closed.

·

The electrical key is in the luggage compartment (luggage compartment key certification result is OK).


Warning Method Combination Meter Assembly Buzzer -
Multi-information Display The following warning message is displayed:
·

Key Detected in Vehicle


Wireless Door Lock Buzzer Sounds continuously*
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The luggage compartment door is closed → opened.

·

The vehicle speed is above 5 km/h (3 mph).

·

5 seconds elapse.





x.

Situation I

The door is locked with the electrical key left in the vehicle. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft

*1: Keyless lock operation is door lock operation without using the electrical key. First, set the perform the door lock operation when the door is open, and close the door while pulling the door handle to lock the door.

*2: Models with thatcham function

*3: Models with answer back buzzer function

Warning Active Condition Condition 1
The warning is activated when all of the following conditions are met:
·

The door is locked using the keyless lock operation.*1

·

The electrical key is in the vehicle (interior key certification result is OK).

·

The vehicle speed is not detected.


Condition 2
The warning is activated when all of the following conditions are met: *2
·

The power source is turned off.

·

All doors are closed and locked, or after unlocking, before a door is opened.

·

A lock operation is performed without using the entry function.

·

The electrical key is in the vehicle (interior key certification result is OK).


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Key Detected in Vehicle


Advisory Display -
Wireless Door Lock Buzzer Sounds continuously*3
Wireless Door Lock Buzzer Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

5 seconds elapse.

·

The power source is turned to another mode.

·

Any door is opened.

·

Lock operation is detected.

·

The vehicle speed is above 5 km/h (3 mph).


"Key Detected in Vehicle" Message Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

60 seconds elapse.

·

The power source is turned to another mode.

·

Lock operation is detected.

·

The vehicle speed is above 5 km/h (3 mph).





xi.

Situation J

The vehicle is driven using an electrical key that has a low battery. In this situation, the following control is performed:

Possible Effects without Warning Usability function, fuel cell system cannot be restarted

*: Warning performed after 20 minutes of the power source being turned on (IG)

Warning Active Condition Condition 1
The warning is activated when all of the following conditions are met:
·

The power source is turned off after being left on (IG) for more than 20 minutes.

·

The key battery voltage is low (key battery low code is received).

·

The electrical key is in the vehicle (interior key certification result is OK).

·

The vehicle speed is not detected.


Condition 2
The warning is activated when all of the following conditions are met:
·

The fuel cell system is stopped → restarted.

·

The key battery voltage is low (key battery low code is received).

·

The electrical key is in the vehicle (interior key certification result is OK).

·

The vehicle speed is not detected.

·

The low key battery warning for condition 1 was performed.*


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Key Battery Low Replace Key Battery


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

15 seconds elapse.

·

The vehicle speed is above 5 km/h (3 mph).





xii.

Situation K

The steering lock cannot be released or the shift position is changed to a position other than P before the steering lock is unlocked. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when the following condition is met:
The steering lock cannot be released (the steering lock ECU judgment).
Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Push Power Switch While Turning Steering Wheel in Either Direction


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The power switch is pushed while the steering wheel is turned left and right.
The warning is stopped when either of the following conditions is met:
·

15 seconds elapse.

·

The steering lock is released.





xiii.

Situation L

A vehicle speed signal malfunction or malfunction that interferes with steering lock ECU (steering lock actuator assembly) operation has been detected. In this situation, the following control is performed:

Possible Effects without Warning Malfunction detection
Warning Active Condition The warning is activated when either of the following conditions is met:
·

The steering lock ECU (steering lock actuator assembly) or steering lock/unlock position switch is malfunctioning.

·

The vehicle speed is judged as abnormal or vehicle speed signal communication is malfunctioning.


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Smart Entry & Start System Malfunction See Owner's Manual


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

15 seconds elapse.

·

The system returns to normal.





xiv.

Situation M

When the driver attempts to start the fuel cell system after unlocking the driver door using the mechanical key, the electrical key cannot be detected in the vehicle or cannot be detected in the vehicle 2 times in a row. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when the power switch is pressed with all of the following conditions met:
·

The immobiliser system is set.

·

The electrical key is not detected in the vehicle (interior key certification fails).

·

The doors were unlocked using a mechanical key or when the power switch is pressed, a certification error occurs 2 times in a row.


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed for 60 seconds (and then automatically turned off):
·

Press Brake Pedal and Touch Power Switch with Key


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

60 seconds elapse.

·

The electrical key is detected in the vehicle (interior key certification result is OK and transponder certification result is OK).

·

30 seconds have elapsed since the door was opened using a door outside handle.





xv.

Situation N

The power switch is touched with an electrical key when the transmitter battery voltage is low, key cancel function is on or radio interference occurs. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition Transponder certification result is OK.
Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Press Brake Pedal and Push Power Switch to Start


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

10 seconds elapse.

·

The electrical key is detected in the vehicle (interior key certification result is OK).

·

The fuel cell system is started.

·

The immobiliser system is set and interior certification is stopped or key certification fails.





xvi.

Situation O

An electrical key has been registered to the vehicle. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power source is turned off.

·

The driver door is unlocked by an unlock operation from the outside of the vehicle, and then opened.


Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display The following warning message is displayed:
·

A New Key has been Registered Contact Your Dealer for Details


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

60 seconds have elapsed since the warning started.

·

10 days have elapsed since the warning was first displayed.

·

All doors are closed and locked.

·

The power source is turned off.





xvii.

Situation P

The system recognizes the situation that indicates the driver may start the fuel cell system (when the driver enters the vehicle or the power source is on (ACC)). In this situation, the following control is performed:

Possible Effects without Warning Fuel cell system cannot be restarted
Warning Active Condition The warning is activated when either of the following conditions is met:
·

When the door is unlocked from the outside of the vehicle with the power source off, the driver door is closed → opened.

·

Each time the power source mode is changed from off to on (ACC) without the brake pedal depressed.


Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display The following warning message is displayed:
·

Press Brake Pedal and Push Power Switch to Start


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

19 seconds have elapsed since the warning started.

·

The fuel cell system is started.

·

Door lock operation is performed from the outside of the vehicle.

·

Wireless operation is performed from the inside of the vehicle or door lock operation is performed using a wireless door lock function.





xviii.

Situation Q

The driver attempts to turn the power source off with the shift lever in any position other than P. In this situation, the following control is performed:

Possible Effects without Warning Discharged auxiliary battery, vehicle roll-away.
Warning Active Condition The power source is turned off when the shift lever in a position other than P. (Excluding an emergency stop by pressing the power switch 3 times quickly or pressing and holding the power switch for 2 seconds or more.)
Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Shift to P Before Exiting Vehicle


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The shift lever is moved to P.

·

The power source is turned to a mode other than on (ACC).





xix.

Situation R

Under situation Q, the shift lever is moved to P. In this situation, the following control is performed:

Possible Effects without Warning Discharged auxiliary battery, vehicle roll-away.
Warning Active Condition The shift lever is moved to P.
Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Turn Power OFF


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The power source mode is changed to a mode other than on (ACC).

·

The shift lever is in any position other than P.





xx.

Situation S

The system recognizes the situation that indicates the driver may start the fuel cell system (when the power source is on (IG)). In this situation, the following control is performed:

Possible Effects without Warning Fuel cell system cannot be restarted
Warning Active Condition The warning is activated when either of the following conditions is met:
·

Each time the power source mode is changed from off to on (IG) (the fuel cell system is not started) while the shift position is P and the brake pedal is not depressed.

·

When the power source is on (IG) (the fuel cell system is not started) and the shift position is not P, the shift position is changed to P.


Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display The following warning message is displayed:
·

Press Brake Pedal and Push Power Switch to Start


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The power source mode is changed to any mode other than on (IG).

·

The vehicle speed is above 5 km/h (3 mph).

·

This shift position is not P.





xxi.

Situation T

Automatic power off operation occurs. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The shift position is P.

·

The power source is on (ACC) or on (IG).

·

The vehicle speed is not detected and the fuel cell system is stopped.

·

The power source is turned off by the automatic power off function (the vehicle remains not operated for 20 minutes with the power source on (ACC) or for 1 hour with the power source on (IG)).


Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display The following warning message is displayed:
·

Auto Power Off to Conserve Battery


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

10 seconds have elapsed since the warning started.

·

The power source is turned on (ACC) or on (IG).





xxii.

Situation U

The driver stopped the fuel cell system using emergency operation while driving. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when either of the following conditions is met:
·

The fuel cell system is stopped by emergency stop operation while driving.

·

After emergency stop operation, the power source is turned on (IG), the vehicle speed is detected and the fuel cell system is not started.


Warning Method Combination Meter Assembly Multi Buzzer Sounds continuously
Multi-information Display The following warning message is displayed:
·

Shift to N and Push POWER Switch to Restart


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The shift position is changed to P.

·

The vehicle speed is not detected (after the power switch is turned on (IG) using power switch operation).

·

The power switch is operated.

·

The fuel cell system has started.





xxiii.

Situation V

The user performed an emergency fuel cell system stop while driving. In this situation, the following control is performed:

Possible Effects without Warning The driver may not notice that the fuel cell system has been stopped while driving.
Warning Active Condition The fuel cell system is stopped using the emergency engine stop function.
Warning Method Combination Meter Assembly Multi Buzzer Sounds continuously
Multi-information Display -
Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The shift position is changed to P.

·

The vehicle speed is not detected (after the power source is turned on (IG) using power switch operation).

·

The fuel cell system has started.





xxiv.

Situation W

The driver pressed the power switch while driving. In this situation, the following control is performed:

Possible Effects without Warning Wrong operation is prevented
Warning Active Condition The vehicle is moving, the vehicle speed is detected and the power switch is pressed.
Warning Method Combination Meter Assembly Multi Buzzer Sounds intermittently
Multi-information Display -
Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

1.8 seconds have elapsed since the power switch operation was stopped.

·

The power source is turned off.





xxv.

Situation X

The driver pressed the power switch while driving. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The vehicle is moving, the vehicle speed is detected and the power switch is pressed.
Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display The following warning message is displayed:
·

Push and Hold Power Switch for Emergency Stop


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

10 seconds elapse.

·

The power source is turned off.





xxvi.

Situation Y

While the vehicle is stationary and a shift position other than P or N selected, the power source on (IG) and the fuel cell system stopped. In this situation, the following control is performed:

Possible Effects without Warning Vehicle roll-away
Warning Active Condition While the vehicle is stopped and a shift position other than P or N selected, the power source on (IG).
Warning Method Combination Meter Assembly Buzzer Sounds continuously
Multi-information Display The following warning message is displayed:
·

FCV System Stopped Shift to P


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The P position switch (transmission shift main switch) is pushed or the shift position is changed to N.

·

The power source is turned off.

·

The vehicle speed is detected.





xxvii.

Situation Z

While the vehicle is stopped, the power source is on (IG), the electronic shift lever system is normal and the vehicle is in a condition in which the power source mode can be turned on (READY), the shift position is changed to N. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition While the vehicle is stopped and the electronic shift lever system is normal, the shift position is changed to N with the power source on (IG).
Warning Method Combination Meter Assembly Buzzer -
Multi-information Display The following warning message is displayed:
·

Shift to P to Start


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The shift position is changed to a position other than N.

·

The power source is turned off.

·

The fuel cell system is not started.

·

The vehicle speed is detected.

·

The electronic shift lever system is abnormal.





xxviii.

Situation AA

The vehicle started to roll away with the power source on (IG) and the fuel cell system stopped. In this situation, the following control is performed:

Possible Effects without Warning Vehicle roll-away
Warning Active Condition While the vehicle is moving and a shift position other than P or N selected, the power source on (IG) and the fuel cell system stopped.
Warning Method Combination Meter Assembly Buzzer Sounds intermittently
Multi-information Display The following warning message is displayed:
·

FCV System Stopped Stop in a Safe Place


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The shift position is changed to N.

·

The power source is turned off.

·

The fuel cell system has started.

·

The vehicle speed is not detected.





xxix.

Situation AB

The power source is changed to on (ACC). In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The power source is changed to on (ACC).
Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display -
Advisory Display ACCESSORY
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when the following condition is met:
·

The power source is changed to a mode other than on (ACC).





xxx.

Situation AC

The power source is changed to on (IG). In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The power source is changed to on (IG).
Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display -
Advisory Display IGNITION ON
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The power source is changed to a mode other than on (IG).

·

The display in the odometer area is changed due to user operation.






f.

Auxiliary Battery Saving Function

i.

Auxiliary battery saving preserves the vehicle and key batteries. It is activated when the vehicle remains parked for a long time and when the electrical key is left in the exterior actuation area.

Condition Control Reinstatement Condition
When the vehicle remains parked for a long time. Control 1:
No response from electrical key for more than 5 days
·

Door electrical key antennas and electrical key antenna stop emitting signals for creating the actuation area.


Control 2:
No response from electrical key for more than 14 days
·

Door electrical key antennas and electrical key antenna stop emitting signals for creating the actuation area.

·

Door lock sensors and unlock sensors for seats other than the driver seat are disabled.


When the power source is turned on (IG), the control is canceled and the system is returned to normal.
When one of the following conditions is met, the control is returned to control 1:
·

The doors are locked or unlocked using wireless remote control.

·

The doors are locked or unlocked by touching the lock/unlock sensor on the driver door.

·

A door is locked or unlocked using the mechanical key.

·

Door is opened → closed.


When the electrical key is left in the exterior detection area. This state continues longer than 10 minutes
·

Electrical key antenna that is detecting the electrical key stops emitting signals for creating the actuation area.


The control is stopped when one of the following conditions is met:
·

The doors are locked or unlocked using wireless remote control.

·

The doors are locked or unlocked by touching the lock/unlock sensor on the front door.

·

A door is locked or unlocked using the mechanical key.




ii.

In addition to the above functions, the auto power off function helps to reduce drain on the auxiliary battery by turning the power source mode to off when approximately 60 minutes have elapsed since the shift position was changed to P with the power source on (ACC), or the fuel cell system was turned off while the shift position was P, the power source was on (IG) and the vehicle was stationary.



g.

Battery Saving Function of Electrical Key

i.

This function cancels the signal reception waiting state of the electrical key, reducing the consumption of current from its battery.


ii.

The electrical key can be placed into and taken out of battery saving mode. When the electrical key is in battery saving mode, the entry and start system will not be able to detect the transmitter, as the transmitter will not respond to signals from the vehicle. The function of the entry and start system will not operate if the electrical key is in battery saving mode.


iii.

Pressing the unlock button of the electrical key twice while pressing the lock button (the indicator light of the electrical key blinks 4 times) selects battery saving mode for the electrical key.


iv.

Battery saving mode can be canceled by pressing any button on the electrical key.



h.

Entry Unlock Mode Switching Function (Manual Operation)

i.

The following entry unlock modes can be selected when using the entry unlock mode switching function. However, the initial setting varies depending on the model.

·

All door unlock mode: When the sensor of a door outside handle is touched, an entry unlock operation is performed simultaneously for all doors.

·

Driver door unlock mode: When the sensor of the driver side door outside handle is touched, an entry unlock operation is performed for the driver door only. If any other door handle is touched, an entry unlock operation is performed simultaneously for all doors.



ii.

When customizing through manual operation:

1.

Turn the power source off.

2.

Check that the LED of the electrical key is not illuminated, and then press and hold the lock and unlock buttons of the electrical key for 5 seconds or more while the electrical key is in the actuation area.

3.

Check the current setting.

HINT:
·

The mode changes from all door unlock mode to driver door unlock mode and then back to all door unlock mode.

·

The answer back (wireless door lock buzzer*, buzzer in the combination meter assembly) operation for each mode is indicated in the table below.

*: Models with answer back buzzer function




*: Models with answer back buzzer function

Currently Selected Mode Answer Back (Wireless Door Lock Buzzer)* Answer Back (Buzzer in Combination Meter Assembly)
All door unlock mode Buzzer sounds twice (short beeps) Buzzer sounds once
Driver door unlock mode Buzzer sounds 3 times (short beeps) Buzzer sounds once

4.

Release the lock and unlock buttons of the electrical key.

5.

Check that the LED of the electrical key is not illuminated, and then press and hold the lock and unlock buttons of the electrical key for 5 seconds or more to change the mode.

HINT:

Repeat the procedure as necessary to select the desired mode.


6.

Unlock the doors with the wireless operation, and then open any door.

Y269879E03
1.406,1.729 1.719,1.927 0.313,0.198 10 false ON 1.375,1.979 1.75,2.146 0.375,0.167 10 false OFF 1.969,2.104 3.104,2.26 1.135,0.156 10 false Sounds 3 times 1.948,3.125 3.083,3.281 1.135,0.156 10 false Sounds 2 times 1.417,0.583 3.667,1.25 2.25,0.667 10 false Wireless Door Lock Buzzer (Models with Answer Back Buzzer Function) 4.583,0.479 6.417,0.667 1.833,0.188 10 false Combination Meter Assembly 4.333,1.063 6.167,1.25 1.833,0.188 10 false Multi-information Display 1.583,2.719 1.896,2.917 0.313,0.198 10 false ON 1.583,3 1.958,3.167 0.375,0.167 10 false OFF 6.427,1.063 6.917,1.25 0.49,0.188 10 false Buzzer 6.427,2.313 6.917,2.667 0.49,0.354 10 false Sounds once 4.75,1.813 6.083,2.167 1.333,0.354 10 false Driver door "OPEN" indication 4.667,2.927 6.333,3.094 1.667,0.167 10 false All door "OPEN" indication 0.26,1.854 1.01,2.042 0.75,0.188 10 false Driver Door 0.302,2.938 1.042,3.125 0.74,0.188 10 false All Doors




i.

Key Cancel Function

i.

The following system functions can be deactivated by using the key cancel procedure.

·

Entry unlock/lock

·

Power trunk lid open

·

Prevention of key confinement

·

Warning



ii.

The system functions can be deactivated by using the following key cancel procedure when the power source is off and the driver door is closed and unlocked.

*: Perform all these 3 steps within 30 seconds of the previous step.

Key Cancel Procedure The procedure is as follows:
·

Press the unlock button of the electrical key once.

·

Within 5 seconds of the step above, open the driver door (Driver Door: Close → Open).

·

Within 5 seconds of the step above, press the unlock button of the electrical key twice.

·

Repeat close → open for the driver door twice* (Driver Door: Open → Close → Open → Close → Open).

·

Press the unlock button of the electrical key twice.*

·

Repeat close → open for the driver door once* (Driver Door: Open → Close → Open).

·

Within 5 seconds of the step above, close the driver door.


When the cancel procedure is complete, the buzzer sounds twice. Meanwhile, when the procedure is performed again to resume the system, the buzzer sounds once.



j.

Key Code Registration Function

i.

The table below shows the 3 special ID code registration function modes through which up to 7 different transmitter recognition codes can be registered. For details, refer to the Repair Manual.

Mode Function
Rewrite Clears all previously registered codes and registers only the newly received codes. This mode is used whenever the certification ECU is replaced.
Add Adds a newly received code while preserving previously registered codes. This mode is used when adding a new transmitter.
Confirm Confirms how many codes are currently registered. When adding a new code, this mode is used to check how many codes already exist.




DIAGNOSIS


a.

Start Function

i.

The certification ECU can detect malfunctions in the entry and start system when the power source is on (IG).


ii.

When the ECU detects a malfunction, a message is displayed on the multi-information display to warn the driver. At the same time, the ECU stores a 5-digit Diagnostic Trouble Code (DTC) in its memory.


iii.

The indicator light warning continues for 15 seconds even after the power source is turned off.


iv.

The 5-digit DTCs can be read after connecting the Global TechStream (GTS) to the DLC3.


v.

The entry and start system may not operate successfully if a malfunction occurs.