Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BODY STRUCTURE
NM37H0E _59 Vehicle Exterior _097723 EXTERIOR PANELS / TRIM _0467012 BODY STRUCTURE DE DETAILS F

EXTERIOR PANELS / TRIM  BODY STRUCTURE  DETAILS  SOUND ABSORBING AND VIBRATION DAMPING MATERIAL  


CONSTRUCTION


a.

Sound Absorption and Insulation Structure

i.

Various types of silencers are positioned around the floor panel and fuel cell unit compartment to greatly suppress vibration and noise that are transmitted into the interior from parts such as the motor and tires, achieving superior quietness. Also, materials such as foamed materials, sound insulation sealant and damping materials are optimally positioned to achieve superior NVH* performance.

HINT:

*: An abbreviation created by taking the first letter of Noise (unpleasant sounds and loud sounds), Vibration (vibrations from the motor and tires) and Harshness (vibrations felt through the steering wheel, seats and floor according to height changes in the road surface, etc.). NVH is used to describe the level of riding comfort and sound quality actually experienced by passengers.




b.

Floor Silencer

i.

The floor silencer (applied damping materials) optimal thickness varies by the area, is lightweight and provides excellent quietness. These characteristics allow the floor silencer to reduce road and motor noise which enters the cabin.


ii.

In what put out for coating of the thickness of the damping materials, I planned improvement of the silent nature and coexistence of the Mass reduction.

V129645C01
0.688,5.344 1,5.5 0.313,0.156 10 false : *a
*a Floor Silencer - -




c.

Sealing Material

i.

Foamed materials, NV covers and sponge sealant are optimally placed in the side member opening and front header to suppress wind noise and road noise which enter the cabin.

Sealing Material (The illustration shown is an example only.)
V129647C01
0.719,3.135 1.031,3.292 0.313,0.156 10 false : *a 0.719,3.458 1.031,3.615 0.313,0.156 10 false : *b
*a Sponge *b Foamed Material




d.

Sound Absorption and Insulation Structure around Fuel Cell Unit Compartment

i.

A hood insulator is provided on the rear of the hood sub-assembly. This achieves excellent sound insulation performance.

V129650C01
2.75,1.583 2.167,1 2.167,1 2.083,1 true 3.25,1.333 2.667,0.75 2.667,0.75 2.583,0.75 true 1.927,0.958 2.24,1.115 0.313,0.156 10 false *1 2.417,0.698 2.729,0.854 0.313,0.156 10 false *2
*1 Hood Insulator *2 Hood Sub-assembly



ii.

The dash panel insulator outer is provided in the fuel cell unit compartment side of the dash panel and a dash panel insulator assembly is provided in the cabin side. This structure absorbs and insulates mechanical noise and ensures excellent quietness.


iii.

The dash panel insulator assembly uses a 3-layered construction that reduces the opening ratio* and ensures thickness to ensure superior sound absorption and insulation performance.

HINT:

*: Opening area ratio for the entire area of the insulator


V129649C01
1.875,1.708 1.875,0.542 1.875,0.542 1.792,0.542 true 2,3.667 1.917,3.667 1.917,3.667 1.917,2.083 true 6.25,3.25 6.167,3.25 6.167,3.25 6.167,2.75 true 6.031,3.333 5.948,3.333 5.948,3.333 5.948,2.833 true 5.583,3.25 5.5,3.25 5.5,3.25 5.5,2.75 true 1.656,0.458 1.969,0.615 0.313,0.156 10 false *1 2.031,3.594 2.344,3.75 0.313,0.156 10 false *2 4.771,0.448 5.083,0.604 0.313,0.156 10 false *a 5.615,3.188 5.927,3.344 0.313,0.156 10 false *b 6.073,3.271 6.385,3.427 0.313,0.156 10 false *c 6.302,3.177 6.615,3.333 0.313,0.156 10 false *d
*1 Dash Panel Insulator Outer *2 Dash Panel Insulator Assembly
*a Material Structure *b Urethane
*c Olefin Sheet *d Felt



iv.

An insulator with superior sound absorption effects (sound insulation material) is used around the fender splash shield sub-assembly front and rear wheel house liner to suppress the sound created by flying sand and water from the wheelhouse and road noise in order to provide excellent quietness.

Fender Liner (The illustration shown is an example only.)
V129651C01
0.354,1.083 0.438,1.083 0.438,1.083 0.854,1.5 true 5.188,0.583 5.271,0.583 5.271,0.583 5.688,1 true 2.615,2.344 3.031,2.76 3.031,2.76 3.115,2.76 true 5.177,3.531 5.594,3.115 5.594,3.115 5.677,3.115 true 6.083,3.99 6.5,3.573 6.5,3.573 6.583,3.573 true 5.333,4.688 5.417,4.688 5.417,4.688 5.833,4.271 true 0.563,5.396 0.646,5.396 0.646,5.396 1.063,4.979 true 3.344,4.146 3.76,3.729 3.76,3.729 3.844,3.729 true 5.438,2.021 5.854,2.438 5.854,2.438 5.938,2.438 true 0.208,1.021 0.521,1.177 0.313,0.156 10 false *1 3.146,2.688 3.458,2.844 0.313,0.156 10 false *2 5.177,4.635 5.49,4.792 0.313,0.156 10 false *3 3.885,3.677 4.198,3.833 0.313,0.156 10 false *4 5.031,0.51 5.344,0.667 0.313,0.156 10 false *a 5.708,3.052 6.021,3.208 0.313,0.156 10 false *a 6.615,3.5 6.792,3.656 0.177,0.156 10 false *a 0.396,5.344 0.708,5.5 0.313,0.156 10 false *3 5.969,2.365 6.281,2.521 0.313,0.156 10 false *2
*1 Fender Splash Shield Sub-assembly Front RH *2 Fender Splash Shield Sub-assembly Front LH
*3 Rear Wheel House Liner LH *4 Rear Wheel House Liner RH
*a Insulator - -




e.

Door

i.

A polypropylene resin service hole cover is used, reducing noise that enters from the outside to the cabin through the doors.

V129652C01
1.292,2.073 0.542,1.323 0.542,1.323 0.458,1.323 true 5.104,2.271 5.771,2.938 5.771,2.938 5.854,2.938 true 2.865,2.542 3.781,3.458 3.781,3.458 3.865,3.458 true 0.323,1.26 0.635,1.417 0.313,0.156 10 false *1 3.896,3.385 4.208,3.542 0.313,0.156 10 false *2 5.885,2.865 6.198,3.021 0.313,0.156 10 false *3
*1 Outer Mirror Install Hole Cover RH *2 Front Door Service Hole Cover RH
*3 Rear Door Service Hole Cover RH - -




f.

Floor Panel Sheet Thickness Optimization

i.

Connecting rigidity and panel thickness are increased in areas close to passengers to suppress panel vibrations. As a result, superior riding comfort is ensured.

·

The toe board reinforcement (*1 in illustration) is connected to part of the rocker (front floor reinforcement (*2 in illustration)) to suppress panel vibrations.

·

The front floor pan (*3 in illustration) uses different thickness tailored blank material. The sheet thickness is increased where passengers place their feet to suppress panel vibrations.

·

The front floor panel CTR (*4 in illustration) uses different thickness tailored blank material. The sheet thickness is increased around the floor tunnnel to suppress panel vibrations.

·

Thick sheets are used in the dash panel sub-assembly (*5 in illustration) to suppress panel vibrations.



ii.

A heavy underbody structure is used to achieve a low center of gravity and improve the sense of material quality. Also, steel cabin parts are used to achieve stable mode control during collisions.

V129653C01
5.083,5.542 5.083,6.542 5.083,6.542 5.167,6.542 true 5.656,6.104 5.656,6.521 5.656,6.521 5.74,6.521 true 2.25,6.083 2.25,6.5 2.25,6.5 2.333,6.5 true 1.667,5.5 1.667,6.5 1.667,6.5 1.75,6.5 true 6.521,1.271 6.521,2.271 6.521,2.271 6.604,2.271 true 5.708,1.26 5.708,2.26 5.708,2.26 5.792,2.26 true 2.167,0.667 2.25,0.667 2.25,0.667 2.25,1.083 true 5.833,2.188 6.146,2.344 0.313,0.156 10 false *1 6.646,2.208 6.958,2.365 0.313,0.156 10 false *2 5.781,6.448 5.969,6.604 0.188,0.156 10 false *3 2.375,6.427 2.688,6.583 0.313,0.156 10 false *4 2,0.615 2.313,0.771 0.313,0.156 10 false *5 5.188,6.458 5.385,6.625 0.198,0.167 10 false *a 1.771,5.635 2.083,5.792 0.313,0.156 10 false *b 4.635,5.708 4.948,5.865 0.313,0.156 10 false *c 1.365,5.396 1.677,5.552 0.313,0.156 10 false *d 1.792,6.427 1.99,6.594 0.198,0.167 10 false *a 4.417,5.448 4.729,5.604 0.313,0.156 10 false *b
*1 Toe Board Reinforcement RH *2 Front Floor Reinforcement RH
*3 Front Floor Pan RH *4 Front Floor Panel CTR
*5 Dash Panel Sub-assembly - -
*a Tailored Blank Line *b Sheet Thickness: 1.2 mm (0.05 in.)
*c Sheet Thickness: 0.9 mm (0.04 in.) *d Sheet Thickness: 1.4 mm (0.06 in.)



iii.

A center floor silencer sheet is provided directly above the TA motor, decreasing the motor gear noise that passes from outside the vehicle through the floor and enters the interior.

V129654C01
2,2.333 2.917,3.25 2.917,3.25 3,3.25 true 5.333,2.583 5.75,3 5.75,3 5.833,3 true 5.688,1.302 6.104,0.885 6.104,0.885 6.188,0.885 true 3.042,3.167 3.354,3.323 0.313,0.156 10 false *1 5.865,2.917 6.177,3.073 0.313,0.156 10 false *2 5.323,3.104 5.635,3.26 0.313,0.156 10 false *a 6.24,0.802 6.552,0.958 0.313,0.156 10 false *1 1.844,1.99 2.156,2.146 0.313,0.156 10 false A 1.417,2.708 1.729,2.865 0.313,0.156 10 false A
*1 Center Floor Silencer Sheet *2 TA Motor
*a A - A Cross Section - -