OUTLINE
Toyota Safety Sense
Toyota Safety Sense consists of the following drive assist systems and contributes to a safe and comfortable driving experience:
PCS (Pre-Collision System)
Dynamic radar cruise control
LTA (Lane Tracing Assist)
RSA (Road Sign Assist) *1
AHB (Automatic High Beam)*2
AHS (Adaptive High beam System)*3
*1: Models with road sign assist system
*2: Models with automatic high beam system
*3: Models with adaptive high beam system
PCS (Pre-Collision System)
The pre-collision system uses a millimeter wave radar sensor assembly and forward recognition camera to detect objects in front of the vehicle. When the system determines that the possibility of a frontal collision with an object is high, a warning operates to urge the driver to take evasive action and the potential brake pressure is increased to help the driver avoid the collision. If the system determines that the possibility of a frontal collision with an object is extremely high, the brakes are automatically applied to help avoid the collision or help reduce the impact of the collision.
Detectable objects
The system can detect the following (The detectable objects differs depending on the function.):
| Regions | Detectable objects | Function availability | Destination/Countries |
|---|---|---|---|
|
*: Except models for Costa Rica |
|||
| A | ·
Vehicles ·
Bicyclists ·
Pedestrians |
·
Pre-collision Warning ·
Pre-collision Brake Assist ·
Pre-collision Braking ·
Emergency Steering Assist ·
Intersection Right/Left Turn Assistance |
·
Europe* ·
China |
| B | ·
Pre-collision Warning ·
Pre-collision Brake Assist ·
Pre-collision Braking |
·
Costa Rica |
|
PRECAUTION
Toyota Safety Sense
Toyota Safety Sense is designed to operate under the assumption that the driver will drive safely, and is designed to help reduce the impact to the occupants and the vehicle in the case of a collision or assist the driver in normal driving conditions. As there is a limit to the degree of recognition accuracy and control performance that this system can provide, do not overly rely on this system. The driver is always responsible for paying attention to the vehicle's surroundings and driving safely.
Limitations of the pre-collision system
The driver is solely responsible for safe driving. Always drive safely, taking care to observe your surroundings. Do not use the pre-collision system instead of normal braking operations under any circumstances. This system will not prevent collisions or lessen collision damage or injury in every situation. Do not overly rely on this system. Failure to do so may lead to an accident, resulting in death or serious injury.
Although this system is designed to help avoid a collision or help reduce the impact of the collision, its effectiveness may change according to various conditions, therefore the system may not always be able to achieve the same level of performance. Read the following conditions carefully. Do not overly rely on this system and always drive carefully.
Conditions under which the system may operate even if there is no possibility of a collision: (For details, refer to the PRE-COLLISION CONTROL.)
Conditions under which the system may not operate properly: (For details, refer to the PRE-COLLISION CONTROL.)
Do not attempt to test the operation of the pre-collision system yourself. Depending on the objects used for testing (dummies, cardboard objects imitating detectable objects, etc.), the system may not operate properly, possibly leading to an accident.
Pre-collision braking
When the pre-collision braking function is operating, a large amount of braking force will be applied.
If the vehicle is stopped by the operation of the pre-collision braking function, the pre-collision braking function operation will be canceled after approximately 2 seconds. Depress the brake pedal as necessary.
The pre-collision braking function may not operate if certain operations are performed by the driver. If the accelerator pedal is being depressed strongly or the steering wheel is being turned, the system may determine that the driver is taking evasive action and possibly prevent the pre-collision braking function from operating.
In some situations, while the pre-collision braking function is operating, operation of the function may be canceled if the accelerator pedal is depressed strongly or the steering wheel is turned and the system determines that the driver is taking evasive action.
If the brake pedal is being depressed, the system may determine that the driver is taking evasive action and possibly delay the operation timing of the pre-collision braking function.
Emergency steering assist (for region A)
As emergency steering assist operation will be canceled when the system determines that lane departure prevention function has been completed.
Emergency steering assist may not operate or may be cancel in the following cases as the system may determine the driver is taking actions.
If the accelerator pedal is being depressed strongly, the steering wheel is being operated sharply, the brake pedal is being depressed or the turn signal lever is being operated. In this case, the system may determine that the driver is taking evasive action and the emergency steering assist may not operate.
In some situations, while the emergency steering assist is operating, operation of the function may be canceled if the accelerator pedal is depressed strongly, the steering wheel is operated sharply or the brake pedal is being depressed and the system determines that the driver is taking evasive action.
When the emergency steering assist is operating, if the steering wheel is held firmly or is operated in the opposite direction to that which the system is generating torque, the function may be canceled.
When to disable the pre-collision system
In the following situations, disable the system, as it may not operate properly, possibly leading to an accident resulting in death or serious injury:
When the vehicle is being towed.
When your vehicle is towing another vehicle.
When transporting the vehicle via truck, boat, train or similar means of transportation.
When the vehicle is raised on a lift with the FC system on and the tires are allowed to rotate freely
When inspecting the vehicle using a drum tester such as a chassis dynamometer or speedometer tester, or when using an on vehicle wheel balancer.
When a strong impact is applied to the front bumper or front grille, due to an accident or other reasons.
If the vehicle cannot be driven in a stable manner, such as when the vehicle has been in an accident or is malfunctioning.
When the vehicle is driven in a sporty manner or off-road.
When the tires are not properly inflated.
When the tires are very worn.
When tires of a size other than specified are installed.
When tire chains are installed.
When a compact spare tire or an emergency tire puncture repair kit is used.
If equipment (snow plow, etc.) that may obstruct the millimeter wave radar sensor assembly or forward recognition camera is temporarily installed to the vehicle.
To avoid malfunction of the millimeter wave radar sensor assembly
Observe the following precautions. Otherwise, the millimeter wave radar sensor assembly may not operate properly, possibly leading to an accident resulting in death or serious injury.
Keep the millimeter wave radar sensor assembly and the radar sensor cover clean at all times.
If the front of the millimeter wave radar sensor assembly or the front or back of the radar sensor cover is dirty or covered with water droplets, snow, etc., clean it.
Clean the millimeter wave radar sensor assembly and radar sensor cover with a soft cloth to avoid damaging them.
| *1 | Millimeter Wave Radar Sensor Assembly | *2 | Radar Sensor Cover |
| *a | The illustrations shown are examples only. | - | - |
Do not attach accessories, stickers (including transparent stickers) or other items to the millimeter wave radar sensor assembly, radar sensor cover or surrounding area.
Do not subject the millimeter wave radar sensor assembly or its surrounding area to a strong impact.
Do not disassemble the millimeter wave radar sensor assembly.
Do not modify or paint the millimeter wave radar sensor assembly or radar sensor cover.
In the following cases, the millimeter wave radar sensor assembly must be recalibrated.
When the millimeter wave radar sensor assembly or front grille are removed and installed, or replaced
When the front bumper is replaced
To avoid malfunction of the forward recognition camera
Observe the following precautions. Otherwise, the forward recognition camera may not operate properly, possibly leading to an accident resulting in death or serious injury.
Keep the windshield clean at all times.
If the windshield is dirty or covered with an oily film, water droplets, snow, etc., clean the windshield.
If a glass coating agent is applied to the windshield, it will still be necessary to use the windshield wipers to remove water droplets, etc. from the area of the windshield in front of the forward recognition camera.
Do not attach objects, such as stickers, transparent stickers, etc., to the outer side of the windshield in front of the forward recognition camera (shaded area in the illustration).
| *a | From the top of the windshield to approximately 1 cm (0.4 in.) below the bottom of the forward recognition camera. | *b | Approximately 20 cm (7.9 in.) (Approximately 10 cm (4.0 in.) to the right and left from the center of the forward recognition camera). |
| *c | The illustrations shown are examples only. | - | - |
If the part of the windshield in front of the forward recognition camera is fogged up or covered with condensation or ice, use the windshield defogger to remove the fog, condensation or ice.
If water droplets cannot be properly removed from the area of the windshield in front of the forward recognition camera by the windshield wipers, replace the wiper insert or wiper blade.
Do not attach window tint to the windshield.
Replace the windshield if it is damaged or cracked.
Do not allow liquids to contact the forward recognition camera.
Do not allow bright lights to shine into the forward recognition camera.
Do not dirty or damage the forward recognition camera.
When cleaning the inside of the windshield, do not allow glass cleaner to contact the lens of the forward recognition camera. Also, do not touch the lens.
Do not subject the forward recognition camera to a strong impact.
Do not change the installation position or direction of the forward recognition camera or remove it.
Do not disassemble the forward recognition camera.
Do not modify any components of the vehicle around the forward recognition camera (inside rear view mirror, etc.) or ceiling.
Do not attach any accessories to the hood, front grille or front bumper that may obstruct the forward recognition camera.
If a surfboard or other long object is to be mounted on the roof, make sure that it will not obstruct the forward recognition camera.
Do not modify the headlights or other lights.
If a warning message is displayed on the multi-information display
A system may be temporarily unavailable or there may be a malfunction in the system.
In the following situations, perform the actions specified in the table. When the normal operating conditions are detected, the message will disappear and the system will become operational.
| Situation | Actions |
|---|---|
| When the area around a camera is covered with dirt, moisture (fogged up, covered with condensation, ice, etc.), or other foreign matter | Using the wiper and A/C function, remove the dirt and other attached matter. |
| When the temperature around the forward recognition camera is outside of the operational range, such as when the vehicle is in the sun or in an extremely cold environment. | If the forward recognition camera is hot, such as after the vehicle had been parked in the sun, use the air conditioning system to decrease the temperature around the forward recognition camera.
|
| If the forward recognition camera is cold, such after the vehicle is parked in an extremely cold environment, use the air conditioning system to increase the temperature around the forward recognition camera. | |
| The area in front of the forward recognition camera is obstructed, such as when the hood is open or a sticker is attached to the part of the windshield in front of the forward recognition camera. | Close the hood, remove the sticker, etc. to clear the obstruction. |
| When "Pre-Collision System Radar In Self Calibration Unavailable See Owner's Manual" is displayed. | Check whether there is attached materials on the millimeter wave radar sensor assembly and radar sensor cover, and if there is, remove it. |
In the following situations, if the situation has changed (or the vehicle has been driven for some time) and the normal operating conditions are detected, the message will disappear and the system will become operational.
When the temperature around the millimeter wave radar sensor assembly is outside of the operational range, such as when the vehicle is in the sun or in an extremely cold environment.
When the forward recognition camera cannot detect objects in front of the vehicle, such as when driving in the dark, snow, or fog, or when bright lights are shining into the forward recognition camera.