Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM › from 2021.08
NM37H0E _52 Drivetrain _097278 Q710 HYBRID TRANSMISSION / TRANSAXLE _0462240 ELECTRONIC SHIFT LEVER SYSTEM CO CONTROL F

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  CONTROL  ELECTRONIC SHIFT LEVER CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*: Models with headup display

Shift Control ECU
·

Performs shift control for each shift position based on signals from the shift lever position sensor, P position switch and various ECUs and sends control signals to the EV control ECU.

·

Operates the parking lock motor inside the shift control actuator assembly based on P position switch operation signals and the vehicle condition.


EV Control ECU Receives control signals from the shift control ECU and controls the FCV transaxle.
Certification ECU (Smart Key ECU Assembly) Receives shift position signals from the shift control ECU and outputs FC system start permission signals to the EV control ECU.
Brake Actuator Assembly No. 2 Skid Control ECU Sends the vehicle speed signal to the shift control ECU.
Central Gateway ECU (Network Gateway ECU) Relays and transmits each CAN communication data signal.
No. 2 Semiconductor Power Integration ECU Receives shift position signals from the shift control ECU and illuminates the back-up light.
Luggage Room Relay Block P CON MTR Relay Turns on according to signals from the shift control ECU and supplies power from the auxiliary battery to the parking lock motor inside the shift control actuator assembly.
IGCT No. 1 Relay Turns on according to signals from the EV control ECU and supplies power from the auxiliary battery to the shift control ECU.
Auxiliary Battery Supplies power to the shift control ECU and the parking lock motor inside the shift control actuator assembly.
Shift Control Supply Sub-battery ECU Detects the status of the electric double-layer capacitor and malfunctions of the shift control supply, and sends the information to the shift control ECU.
Backup Relay Opens and closes the power source circuit between the electric double-layer capacitor and DC-DC converter (inverter with converter assembly) or auxiliary battery.
P CON MTR 2 Relay Turns on according to signals from the shift control ECU when the auxiliary battery voltage drops and supplies power from the electric double-layer capacitor to the parking lock motor inside the shift control actuator assembly.
DC-DC Converter Performs voltage boost and step-down for charging and power supply of the electric double-layer capacitor.
Electric Double-layer Capacitor Automatically charged and set on standby when the ignition switch is turned on, and functions as a backup power source to supply power to the shift control ECU and shift control actuator assembly when the power supply from the auxiliary battery is insufficient.
Stop Light Switch Assembly Detects the depressing of the brake pedal and transmits a signal to the shift control ECU.
Shift Lock Control Unit Assembly Shift Lever Position Sensor Detects the shift positions (Home, R, N, D or Br), and transmits the shift position signal to the shift control ECU.
P Position Switch
·

Detects the driver's operation of the parking lock, and sends it to the shift control ECU.

·

Informs the driver that the shift position is P by illuminating the light.


Combination Meter Assembly Br Mode Indicator Indicates that Br mode is selected.
Shift Position Indicator Indicates the shift position (P, R, N or D).
Multi-information Display Shows a message to warn the driver when a system malfunction occurs or the reject function operates.
Buzzer
·

Continuously sounds to warn the driver when the accelerator pedal is depressed with the shift position in N and the ignition switch on (READY).

·

Sounds to warn the driver when a system malfunction occurs or the reject function operates.


Meter Mirror Sub-assembly* Displays the shift position.
Shift Control Actuator Assembly Parking Lock Motor Engages or disengages the transaxle parking lock mechanism.
Rotation Angle Sensor Detects the rotation angle of the rotor in the parking lock motor.


SYSTEM CONTROL


a.

The shift control ECU sends requests to the EV control ECU to switch to a shift range according to each shift position based on the shift lever position sensor signals and vehicle condition.


b.

The shift control ECU operates the parking lock motor inside the shift control actuator assembly based on P position switch operation signals and the vehicle condition to lock and unlock the transaxle parking lock mechanism.

X132495E06
5.198,3.188 5.635,2.896 true 3.958,4.365 6.583,4.813 2.625,0.448 10 false FCV Transaxle with Motor Assembly 5.688,2.781 7.031,3.438 1.344,0.656 10 false Shift Control Actuator Assembly 5.083,1.115 6.188,1.531 1.104,0.417 10 false Shift Control ECU 0.583,3.594 2.583,4.01 2,0.417 10 false Inverter with Converter Assembly 1.083,2.083 3.5,2.479 2.417,0.396 10 false EV Control ECU 0.625,1.563 3.042,1.958 2.417,0.396 10 false Shift Lock Control Unit Assembly 0.781,1.094 2.479,1.531 1.698,0.438 10 false Shift Lever Position Sensor 1.042,0.146 2.469,0.583 1.427,0.438 10 false P Position Switch



FUNCTION


a.

Shift Position Change Function

i.

This system uses the shift control ECU to comprehensively determine driver operations and the vehicle condition to switch the shift position so that the driver can comfortably perform operations.


ii.

An "automatic P position switching function" is provided. When the ignition switch (push start switch) is turned off while the vehicle is stopped and the shift position is not P, the P position is automatically shifted to before switching the power source mode to off.

HINT:
·

If the FC system unavoidably stops while driving with the power source mode on (ACC) and the shift position in N, the P position is automatically shifted to when the vehicle stops.

·

When the auxiliary battery voltage drops while the shift position is not P, the shift position may automatically switch to P.



NOTICE:

While towing with the ignition switch on (IG), do not switch the power source mode to off. The automatic P position switching function may operate and secure the driving wheels with the transaxle parking lock mechanism.



iii.

An "automatic P position changing function when exiting" is provided that automatically switches the shift position to P when the ignition switch is on (IG), the shift position is not in P, and all the following conditions are met. At this case, the buzzer in the combination meter assembly sounds and the warning message is displayed on the multi-information display.

·

When the driver's seat belt is unfastened.

·

When the driver door is opened.

·

When the driver does not depress the brake pedal.

·

When the vehicle is not driving.



NOTICE:

The "automatic P position changing function when exiting" is only a contingency function. Drivers should always press the P position switch and confirm that the shift position is switched to P before exiting the vehicle.



iv.

An "N range hold mode" is provided that enables the ignition switch to be turned off while holding the shift position in N. Perform the following operation to enter "N range hold mode".

1.

Move the shift lever to N.

2.

Return the shift lever to the neutral position.

3.

Move the shift lever to N again. (A buzzer will sound)

4.

Turn the ignition switch off while holding the shift lever in N. (If accidentally released without holding the shift lever in N, it will be necessary to turn the ignition switch off within 5 seconds)

5.

A buzzer will sound and a confirmation message will be displayed on the multi-information display when entering "N range hold mode". (The ignition switch will be turned on (ACC) while the shift position is in N)


HINT:
·

When the P position switch is pressed, the shift position will be switched to P, and N range hold mode will end.

·

Do not unnecessarily turn the ignition switch on (IG) or off when in "N range hold mode", except in case of an emergency. When this operation is repeated 5 times, the shift position will switch to P and "N range hold mode" will end.




v.

The shift position can be shifted to N while driving at or above a fixed speed even when the shift lever is not held in the N position. At this time, the buzzer in the combination meter assembly sounds and the warning message is displayed on the multi-information display.

X146321E06
4.313,1.74 4.563,1.625 true 0.542,0.281 1.469,0.969 0.927,0.688 10 false Power Source Status 1.885,0.302 2.594,0.688 0.708,0.385 10 false Operation 4.323,0.26 5.198,0.604 0.875,0.344 10 false Shift Position 3.125,0.677 3.396,1.01 0.271,0.333 10 false P 3.917,0.677 4.188,1.01 0.271,0.333 10 false R 4.719,0.667 4.99,1 0.271,0.333 10 false N 5.531,0.667 5.802,1 0.271,0.333 10 false D 6.115,0.656 6.938,1.125 0.823,0.469 10 false Br mode 0.833,1.083 1.542,1.469 0.708,0.385 10 false OFF 0.708,1.563 1.417,1.948 0.708,0.385 10 false ON (ACC) 0.75,2.042 1.458,2.427 0.708,0.385 10 false ON (IG) 0.625,3.917 1.417,4.271 0.792,0.354 10 false READY-ON 2.875,1.083 5.156,1.448 2.281,0.365 10 false Unable to change the shift position 2.115,1.073 2.823,1.458 0.708,0.385 10 false - 1.885,2.031 2.594,2.417 0.708,0.385 10 false Shift Lever 1.646,2.51 2.76,2.896 1.115,0.385 10 false P Position Switch 1.885,3.865 2.594,4.25 0.708,0.385 10 false Shift Lever 1.646,5.26 2.76,5.646 1.115,0.385 10 false P Position Switch 0.771,6.031 2.844,6.448 2.073,0.417 10 false : Current position 0.771,6.427 4.365,6.802 3.594,0.375 10 false : Positions to which the shift position can be changed 1.646,1.563 2.76,1.948 1.115,0.385 10 false P Position Switch 4.594,1.531 7,2.229 2.406,0.698 10 false Only when in N range hold mode



b.

Reject Function

i.

A reject function is provided to ensure safety.


ii.

When the following operations are performed, the shift position does not switch and the current shift position is maintained, or the system shifts to neutral (N). At this time, the buzzer in the combination meter assembly sounds, the warning message is displayed in the multi-information display to warn the driver.

Reject Function Target Operation Shift Position After Reject Function Operation Multi-information Display Message Coping Process
Shift operation during auxiliary battery voltage drop Maintains current shift position Battery low
Shifting unavailable
See owner's manual
Switch shift position after charging or replacing auxiliary battery
Shift operation from P position to other position or other position to P position performed repeatedly in short period of time P Shifting unavailable
Wait a moment and
Shift again
Wait for short while, and then perform shift operation
Shift operation from P or N position to Br mode Maintains current shift position Vehicle must be in [D]
to shift into [Br]
After switching shift position to D position, shift to Br mode
·

Shift operation to R, D or Br mode with ignition switch on (IG) and READY indicator light turned off

·

Shift operation from P position to other position with READY indicator light flashing

·

Shift operation from P position to other position with insufficient voltage necessary for shifting


P FC system must be READY
to shift
·

Turn ignition switch on (READY), and then perform shift operation to R, D or Br mode

·

Switch to D position, and then perform shift operation to Br mode


Shift operation from P position to other position with brake pedal released P Press Brake to Shift Depress brake pedal before performing shift operation
When the vehicle is stopped, shift operation from N position to R or D position with brake pedal released N
When the vehicle is stopped, the driver attempted to change the shift position without depressing the brake pedal, after the power of the shift control ECU was temporarily cut off Maintains current shift position
Shift operation from R position directly to Br mode N Shifted into [N]
Vehicle must be in [D]
to shift into [Br]
Switch to D position, and then perform shift operation to Br mode
Shift operation to D position while reversing N Shifted into [N]
Vehicle must be stopped
to shift into [D]
Stop vehicle, and then perform shift operation
Shift operation to R position while driving ahead N Shifted into [N]
Vehicle must be stopped
to shift into [R]
Stop vehicle, and then perform shift operation
P position switch briefly pressed while driving Maintains current shift position - In order to perform shift operation to P position, completely stop vehicle, and then perform P position switch operation
P position switch pressed repeatedly or continually pressed while driving N Shifted into [N]
Vehicle must be stopped
to shift into [P]
Shift operation from P position to other position with accelerator pedal and brake pedal both depressed P Release accelerator to shift Release accelerator pedal, and then perform shift operation while depressing brake pedal
Shift operation from N position to R or D position with accelerator pedal depressed N Release accelerator pedal, and then perform shift operation
Shift operation to N position without holding shift lever in N Maintains current shift position Temporarily hold shift lever
in [N] position
to shift into [N]
When shifting to N position, hold shift lever in N for short while*
Changing the shift state from P position when there is an external connection (during charging or hydrogen refueling) P - Disconnecting external connection, and then perform shift operation while depressing brake pedal

HINT:

*: The system can switch to neutral (N) when the shift lever is not held in neutral (N) only when driving at a fixed speed or more.




c.

Shift Position Indicator

i.

A shift position indicator is provided in the combination meter assembly. The current shift position and possible shift positions are displayed. The normal operation method for shifting to the Br mode is to shift from the D position. Therefore, when a shift position other than D or Br mode is selected, the shift pattern for shifting to the Br mode is not displayed. Also, when the READY indicator light is off with the ignition switch on (IG), the shift pattern for shifting to the R, D or Br mode is not displayed.

Shift Position Indicator in Combination Meter Assembly
X149170C01
1.875,2.469 2.271,2.792 0.396,0.323 10 false *a 5.25,2.469 5.646,2.792 0.396,0.323 10 false *b
*a D Position Selected *b R Position Selected




d.

Shift Related Components Malfunction Display

i.

When a malfunction occurs in the system or shift-related components, the buzzer in the combination meter assembly sounds, the warning message is displayed in the multi-information display to warn the driver.

Multi-information Display Function Constraint or Action to be Taken
Shift System Malfunction
Apply Parking Brake Securely When Parking
See Owner's Manual
·

The transaxle parking lock mechanism may not operate. When parking, select a flat area and securely apply the parking brake.

·

The FC system may not start.

·

When turning the ignition switch (push start switch) off, the system may remain on (ACC). At this time, when the parking brake is applied, it may be possible to switch from on (ACC) to off.

·

The automatic P position switching function may not operate. Before turning the ignition switch (push start switch) off, operate the P position switch and check that the shift position indicator indicates that the shift position is P.


Shift System Malfunction
See Owner's Manual
The system may not operate normally when left alone, which may be dangerous or cause a malfunction
Shift System Malfunction
Stop in a Safe Place
See Owner's Manual
It may not be possible to switch the shift position. Park in a safe area.
[P] Switch Malfunction
Apply Parking Brake Securely When Parking
See Owner's Manual
It may not be possible to switch the shift position to P even by operating the P position switch. When parking, select a flat area and securely apply the parking brake.
Shift System Unavailable
Apply Parking Brake Securely When Parking
See Owner's Manual
·

The transaxle parking lock mechanism may not operate. When parking, select a flat area and securely apply the parking brake.

·

The FC system may not start.

·

When turning the ignition switch (push start switch) off, the system may remain on (ACC). At this time, when the parking brake is applied, it may be possible to switch from on (ACC) to off.


Stop Vehicle in a Safe Place
Push [P] Switch
·

The automatic P position switching function may not operate. When parking, make sure to securely operate the P position switch.

·

This warning message is displayed when the auxiliary battery voltage drops. When parking, make sure to securely operate the P position switch.


Shift System Malfunction
Shifting Unavailable
Drive to a Safe Place and Stop
·

The shift position does not switch from D.

·

Drive to a safe area and park.

·

Slow acceleration may occur.

·

When the vehicle speed drops, driving may not be possible.


Shift System Malfunction
Driving Unavailable
Driving is not possible.




FAIL-SAFE


a.

The electronic shift lever system has a fail-safe function which operates if a malfunction occurs. In this situation, the buzzer in the combination meter assembly sounds and the warning message is displayed in the multi-information display to inform the driver of a malfunction in the system.



DIAGNOSIS


a.

When the shift control ECU detects a malfunction in the electronic shift lever system, the EV control ECU performs a diagnosis and memorizes the failed section. At the same time, the Diagnostic Trouble Code (DTC) is stored in its memory.


b.

The DTC can be read by connecting the GTS to the DLC3. For details, refer to the Repair Manual.