FUNCTION OF MAIN COMPONENTS
The main components in the airbag system have the following functions:
| Components | Function | |
|---|---|---|
|
*1: Models with SRS front passenger knee airbag *2: Models with airbag cut off switch cylinder *3: Models with occupant classification system |
||
| Driver Airbag (Horn Button Assembly) | Used as supplements to the seat belts to help reduce impact to the occupants. | |
| Front Passenger Airbag (Instrument Panel Passenger without Door Airbag Assembly) | ||
| Driver Knee Airbag (Lower No. 1 Instrument Panel Airbag Assembly) | ||
| Front Passenger Knee Airbag (Lower No. 2 Instrument Panel Airbag Assembly)*1 | ||
| Front Seat Airbag Assembly LH | ||
| Front Seat Airbag Assembly RH | ||
| Curtain Shield Airbag Assembly LH | ||
| Curtain Shield Airbag Assembly RH | ||
| Front Seat Outer Belt Assembly LH
·
Seat Belt Pretensioner |
Used to help reduce impact to the occupants. | |
| Front Seat Outer Belt Assembly RH
·
Seat Belt Pretensioner |
||
| Rear Seat Outer Belt Assembly LH
·
Seat Belt Pretensioner |
||
| Rear Seat Outer Belt Assembly RH
·
Seat Belt Pretensioner |
||
| Spiral Cable Sub-assembly | Transmits ignition signals from the airbag ECU assembly to the SRS driver airbag. | |
| Front Airbag Sensor LH | Based on the deceleration of the vehicle during a frontal collision, distortion is created in the sensor and is converted into an electrical signal. | |
| Front Airbag Sensor RH | ||
| Side Airbag Pressure Sensor LH | Detects deformation of the front doors during a side collision using the pressure sensor and sends signals for the airbag ECU assembly to determine if deployment of SRS components is necessary. | |
| Side Airbag Pressure Sensor RH | ||
| Side Airbag Sensor Assembly LH | Based on the deceleration of the vehicle during a side or rear side collision, distortion is created in the sensor and is converted into an electrical signal. | |
| Side Airbag Sensor Assembly RH | ||
| Rear Airbag Sensor LH | ||
| Rear Airbag Sensor RH | ||
| Steering Sensor | Sends steering angle signals to the airbag ECU assembly via CAN communication. | |
| Millimeter Wave Radar Sensor Assembly | Radiates millimeter wave radar forward, uses the reflected millimeter waves for detecting the presence of a vehicle ahead, the vehicle-to-vehicle distance, and the relative speed, and then transmits this information to the forward recognition camera. | |
| Airbag Cut Off Switch Cylinder Sub-assembly*2 | Suspends the SRS front passenger airbag operation. | |
| Driver Seat Belt Buckle Switch (Front Seat Inner Belt Assembly LH) | Detects if the driver seat belt is fastened. | |
| Front Passenger Seat Belt Buckle Switch (Front Seat Inner Belt Assembly RH) | Detects if the front passenger seat belt is fastened. | |
| Rear Outer Passenger Seat Belt Buckle Switch LH (Rear Seat Belt Assembly Inner LH) | Detects if the rear outer passenger seat belt LH is fastened. | |
| Rear Outer Passenger Seat Belt Buckle Switch RH (Rear Seat Belt Assembly Inner) | Detects if the rear outer passenger seat belt RH is fastened. | |
| Airbag ECU Assembly | ·
In the event of a frontal collision, the airbag ECU assembly receives signals from either of the front airbag sensors. The airbag ECU assembly receives the signal via its judgment circuit and also receives another signal from the safing sensor built into the airbag ECU assembly. After receiving a signal from at least one of the front airbag sensors and the safing sensor, the airbag ECU assembly determines whether the SRS driver airbag, SRS front passenger airbag, SRS driver knee airbag, SRS curtain shield airbag assemblies and front and rear seat belt pretensioners should be deployed. The airbag ECU assembly also diagnoses system malfunctions. ·
In the event of a side or rear side collision, the airbag ECU assembly receives signals from the side airbag sensor, side airbag sensor assembly or rear airbag sensor. The airbag ECU assembly receives the signal via its judgment circuit and also receives another signal from the safing sensor built into the airbag ECU assembly. After receiving a signal from at least one of the side sensors and the safing sensor, the airbag ECU assembly determines whether the SRS driver, front passenger side airbags, SRS curtain shield airbag assemblies and seat belt pretensioners should be deployed. The airbag ECU assembly also diagnoses system malfunctions. |
|
| Occupant Detection ECU*3 | Judges whether the front passenger seat is occupied based on signals from the 2 occupant classification sensors and the front passenger seat belt buckle switch. | |
| EV Control ECU | Sends shift position signals and the operation status of the EV control system to the airbag ECU assembly via CAN communication. | |
| Skid Control ECU Assembly | Sends vehicle speed signals, brake pedal operation signals and the operation status of the brake control system to the airbag ECU assembly via CAN communication. | |
| Forward Recognition Camera | Prepares the seat belt pretensioners to operate when the PCS (Pre-Collision System) determines that the possibility of a collision with another vehicle is high. | |
| Combination Meter Assembly | SRS Warning Indicator | Turns on to alert the driver when the airbag ECU assembly detects a malfunction in the SRS airbag system. |
| Multi-information Display | Displays a warning message to inform the driver of a malfunction in the SRS airbag system. | |
| Buzzer | Sounds to warn the driver of a malfunction in the SRS airbag system. | |
| Telltale Light Assembly*2 | AIRBAG ON/OFF Indicator Light | Illuminates to inform the occupants whether the airbags and seat belt pretensioner for front passenger are active state or inactive state. |
| Telltale Light Assembly*3 | AIRBAG ON Indicator Light | Turns on to inform the driver when the occupant detection ECU has put the SRS front passenger airbag and SRS front passenger knee airbag into an active state. |
| AIRBAG OFF Indicator Light | ·
Turns on to inform the driver when the occupant detection ECU has put the SRS front passenger airbag and SRS front passenger knee airbag into an inactive state. ·
Turns on to alert the driver when the airbag ECU assembly detects a malfunction in the occupant classification system. |
|
| DLC3 | The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. | |
OPERATING CONDITION
Frontal Collision
Deceleration sensors used for the SRS airbag system are installed on various parts on the vehicle and calculate the deceleration (or acceleration) rate of each part during a collision.
Depending on the situation, the airbag ECU assembly sends a deployment signal to each SRS airbag based on the information from each sensor.
Frontal collision signals are produced based on the information from the airbag ECU assembly and front airbag sensors. Frontal collision signals are used to deploy the SRS airbags and activate the seat belt pretensioners as indicated in the table below.
If the severity of the collision is particularly high, the SRS curtain shield airbag assemblies LH and RH are deployed.
Side Collision
The SRS side airbag and SRS curtain shield airbag assembly on the side of the collision are deployed and the front and rear seat belt pretensioners on the side of the collision are activated based on signals from the side airbag pressure sensor, side airbag sensor assembly and airbag ECU assembly.
If the severity of the collision is particularly high, the SRS curtain shield airbag assembly on the side opposite the collision is deployed and the front and rear seat belt pretensioners on the side opposite the collision are activated.
Rear Side Collision
The SRS curtain shield airbag assembly on the side of the collision are deployed and the rear seat belt pretensioner on the side of the collision is activated based on signals from the rear airbag sensor, side airbag sensor assembly and airbag ECU assembly.
If the severity of the collision is particularly high, SRS curtain shield airbag assembly on the side opposite the collision is deployed and rear seat belt pretensioner on the side opposite the collision is activated.
Roll Over
The SRS curtain shield airbag assemblies LH and RH are deployed and the front and rear seat belt pretensioners are activated based on signals that show the vehicle's roll angle and rotation speed.
SYSTEM CONTROL
Frontal Collision (Models without Occupant Classification System)
There are 3 SRS airbags which deploy in the event of a frontal collision: the SRS driver airbag, SRS front passenger airbag and SRS driver knee airbag. These SRS airbags deploy simultaneously. In addition, the seat belt pretensioners contained in the front seat outer belt assemblies LH and RH and the rear seat outer belt assemblies LH and RH are also activated.
For a frontal collision, if a front airbag sensor detects an impact, it informs the airbag ECU assembly. The airbag ECU assembly causes the SRS driver airbag, SRS front passenger airbag and SRS driver knee airbag to deploy. Additionally, the airbag ECU assembly activates the front and rear seat belt pretensioners.
If the severity of the collision is particularly high, the SRS curtain shield airbag assemblies LH and RH are deployed.
| Airbag | Information | Source |
|---|---|---|
|
*: Models with airbag cut off switch cylinder |
||
| Driver | Extent of Impact | ·
Front Airbag Sensor LH or RH ·
Airbag ECU Assembly |
| Seat Belt Condition | Driver Seat Belt Buckle Switch (Non-contact Type) | |
| Front Passenger | Extent of Impact | ·
Front Airbag Sensor LH or RH ·
Airbag ECU Assembly |
| Airbag Cut Off Switch Cylinder Status* | Airbag Cut Off Switch Cylinder Sub-assembly | |
| Seat Belt Condition | Front Passenger Seat Belt Buckle Switch (Non-contact Type) | |
Frontal Collision (Models with Occupant Classification System)
There are 4 SRS airbags which deploy in the event of a frontal collision: the SRS driver airbag, SRS front passenger airbag, SRS driver knee airbag and SRS front passenger knee airbag. These SRS airbags deploy simultaneously. The SRS driver airbag and SRS front passenger airbag use dual-stage control. In addition, the seat belt pretensioners contained in the front seat outer belt assemblies LH and RH and the rear seat outer belt assemblies LH and RH are also activated.
The airbag ECU assembly detects the information in the table below from various sources in order to activate the dual-stage control.
For a frontal collision, if a front airbag sensor detects an impact, it informs the airbag ECU assembly. The airbag ECU assembly causes the SRS driver airbag, SRS front passenger airbag, SRS driver knee airbag and SRS front passenger knee airbag to deploy. Additionally, the airbag ECU assembly activates the front and rear seat belt pretensioners.
If the severity of the collision is particularly high, the SRS curtain shield airbag assemblies LH and RH are deployed.
| Airbag | Information | Source |
|---|---|---|
| Driver | Extent of Impact | ·
Front Airbag Sensor LH or RH ·
Airbag ECU Assembly |
| Driver Seat Position | Seat Position Airbag Sensor | |
| Seat Belt Condition | Driver Seat Belt Buckle Switch (Non-contact Type) | |
| Front Passenger | Extent of Impact | ·
Front Airbag Sensor LH or RH ·
Airbag ECU Assembly |
| Occupant Detection | 2 Occupant Classification Sensors (Connected to the airbag ECU assembly through the occupant detection ECU.) | |
| Seat Belt Condition | Front Passenger Seat Belt Buckle Switch (Non-contact Type) (Connected to the airbag ECU assembly through the occupant detection ECU.) |
Side Collision
There are 2 SRS airbags which deploy in the event of a side collision: the SRS side airbag and SRS curtain shield airbag assembly on the side of the collision. These SRS airbags deploy simultaneously. Additionally, at the same time, the front and rear seat belt pretensioners on the side of the collision are also activated.
For a side collision, if the side airbag pressure sensor and side airbag sensor assembly detect an impact, it informs the airbag ECU assembly. The airbag ECU assembly causes the SRS side airbag and SRS curtain shield airbag assembly on the side of the collision to deploy simultaneously, and activates the front and rear seat belt pretensioners on the side of the collision.
If the severity of the collision is particularly high, the SRS curtain shield airbag assembly on the side opposite the collision is deployed and the front and rear seat belt pretensioners on the side opposite the collision are activated.
Rear Side Collision
The SRS curtain shield airbag assembly on the side of the collision deploy in the event of a rear side collision. Additionally, at the same time, the rear seat belt pretensioner on the side of the collision is also activated.
For a rear side collision, if the rear airbag sensor or side airbag sensor assembly detects an impact, it informs the airbag ECU assembly and the airbag ECU assembly causes the SRS curtain shield airbag assembly on the side of the collision to deploy simultaneously, and activates the rear seat belt pretensioner on the side of the collision.
If the severity of the collision is particularly high, the SRS curtain shield airbag assembly on the side opposite the collision is deployed and the rear seat belt pretensioner on the side opposite the collision is activated.
Roll Over (Models with Occupant Classification System)
If the vehicle is tilted and rolls over, the airbag ECU assembly activates the SRS curtain shield airbag assemblies LH and RH and seat belt pretensioners for the driver, front passenger and rear passengers based on signals that show the vehicle's roll angle and rotation speed.
If the vehicle rolls over in a side collision, the airbag ECU assembly causes the SRS side airbag and SRS curtain shield airbag assembly on the side of the collision to deploy simultaneously, and activates the front and rear seat belt pretensioners on the side of the collision based on signals from the side airbag pressure sensor, side airbag sensor assembly. Meanwhile, the airbag ECU assembly activates the SRS curtain shield airbag assembly on the side opposite the collision and the front and rear seat belt pretensioners on the side opposite the collision, based on lateral deceleration and rotation speed signals.
Primary Check Illumination Control
After the ignition switch is turned on (IG), the airbag ECU assembly illuminates the SRS warning indicator in the combination meter assembly for approximately 6 seconds and conducts the primary check. During the primary check, the ignition of SRS airbags is prohibited and a diagnosis of the airbag ECU assembly is performed. If a malfunction is detected during the primary check, the SRS warning indicator will remain on even after 6 seconds have elapsed.
After the ignition switch is turned on (IG), the airbag ECU assembly operates the front passenger airbag ON/OFF indicator lights as shown below to check for an open in the indicator light circuits.
DIAGNOSIS
If the airbag ECU assembly detects a malfunction in the SRS airbag system, the airbag ECU assembly stores the malfunction data in memory in addition to illuminating the SRS warning indicator.
The airbag ECU assembly outputs malfunction data and Diagnostic Trouble Codes (DTCs) to the Global TechStream (GTS).
The DTCs can be read by connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.
If the SRS airbags deploy, the airbag ECU assembly will turn on the SRS warning indicator. However, unlike an ordinary malfunction, a DTC will not be stored. The SRS warning indicator cannot be manually turned off. It is necessary to replace the airbag ECU assembly with a new one.