Home › Vehicle Exterior › LIGHTING (EXT) › STOP LIGHT SWITCH
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0440752 STOP LIGHT SWITCH G

LIGHTING (EXT)  STOP LIGHT SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84340 1.INSPECT STOP LIGHT SWITCH ASSEMBLY

a.

Disconnect the stop light switch assembly connector.

i.
E270964C62
1.49,0.208 1.896,0.417 0.406,0.208 1.583,1.844 1.719,1.354 true 2.219,1.24 2.698,1.125 true 0.802,1.104 1.26,1.271 true 0.125,0.073 0.438,0.229 0.313,0.156 10 false *a 0.688,1.021 0.844,1.219 0.156,0.198 10 false B 2.75,1.042 2.906,1.24 0.156,0.198 10 false B 1.448,1.865 1.823,2.052 0.375,0.188 10 false GND 1.625,0.24 2.083,0.438 0.458,0.198 10 false A3
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A3)Location & Routing

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

A3-1(B) - A3-3(GND) Ignition switch off 11 to 14 V
A3-5(B) - A3-3(GND) Ignition switch on (IG) 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A3)Location & Routing

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

A3-3(GND) - Body ground Always Below 1 Ω


HINT:

If the result is not as specified, repair or replace the wire harness.




b.

Reconnect the stop light switch assembly connector.

i.
E240777C31
1.573,0.146 1.906,0.344 0.333,0.198 1.948,0.979 2.573,0.469 true 0.771,0.49 1.5,0.99 true 1.354,0.344 1.708,0.958 true 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 1.063,0.229 1.521,0.427 0.458,0.198 10 false GND 2.625,0.375 2.781,0.573 0.156,0.198 10 false L 0.677,0.375 0.833,0.573 0.156,0.198 10 false L 1.646,0.198 1.958,0.396 0.313,0.198 10 false A3
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A3)Location & Routing

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

A3-2(L) - A3-3(GND) Ignition switch off, brake pedal released 1.0 V or less
A3-2(L) - A3-3(GND) Ignition switch off, brake pedal depressed 11 to 14 V
A3-4(L) - A3-3(GND) Ignition switch on (IG), brake pedal released 11 to 14 V
A3-4(L) - A3-3(GND) Ignition switch on (IG), brake pedal depressed 0 to 1.5 V


HINT:

If the result is not as specified, replace the stop light switch assembly.