Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › PATTERN SELECT SWITCH
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0442251 PATTERN SELECT SWITCH G

Q710 HYBRID TRANSMISSION / TRANSAXLE  PATTERN SELECT SWITCH  INSPECTION  


PROCEDURE

Hide 84720A 1.INSPECT NO. 1 PATTERN SELECT SWITCH ASSEMBLY (DRIVE MODE)

a.
C444793C03
1.542,0.229 1.906,0.438 0.365,0.208 0.938,1.865 1.177,1.865 1.177,1.865 1.573,1.323 true 1.813,1.844 1.813,1.333 true 2.24,1.313 2.552,1.885 2.552,1.885 2.781,1.885 true 0.063,0.052 0.344,0.292 0.281,0.24 10 false *a 2.823,1.813 3.25,2.031 0.427,0.219 10 false DMS+ 0.542,1.802 0.948,2 0.406,0.198 10 false DMS- 1.792,1.875 1.99,2.104 0.198,0.229 10 false E 1.635,0.25 1.917,0.438 0.281,0.188 10 false D5
*a Component without harness connected
(No. 1 Pattern Select Switch Assembly (DRIVE MODE))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D5)Location & Routing

Click Connector(D5)Instrument Panel>Instrument Panel Wire>No. 1 Pattern Select Switch Assembly

D5-1 (DMS+) - D5-3 (E) When the DRIVE MODE switch is operated and held on the top side Below 10 Ω
D5-1 (DMS+) - D5-3 (E)
D5-4 (DMS-) - D5-3 (E)
When the DRIVE MODE switch is not operated 10 kΩ or higher
D5-4 (DMS-) - D5-3 (E) When the DRIVE MODE switch is operated and held on the bottom side Below 10 Ω


If the result is not as specified, replace the No. 1 pattern select switch assembly (DRIVE MODE).


b.
C444793C04
1.531,0.198 1.917,0.406 0.385,0.208 1.021,1.865 1.229,1.865 1.229,1.865 1.427,1.323 true 2.5,1.885 2.208,1.885 2.208,1.885 2.021,1.323 true 0.063,0.052 0.344,0.292 0.281,0.24 10 false *a 0.719,1.802 1.052,2 0.333,0.198 10 false ILL+ 2.542,1.813 2.927,2.01 0.385,0.198 10 false ILL- 1.635,0.219 1.917,0.438 0.281,0.219 10 false D5
*a Component without harness connected
(No. 1 Pattern Select Switch Assembly (DRIVE MODE))


Apply battery voltage between the terminals of the No. 1 pattern select switch assembly (DRIVE MODE), and check the illumination condition of the No. 1 pattern select switch assembly (DRIVE MODE).

Standard:
Measurement Condition Specified Condition
Battery positive (+) → D5-5 (ILL+)
Battery negative (-) → D5-2 (ILL-)
Illuminates


If the result is not as specified, replace the No. 1 pattern select switch assembly (DRIVE MODE).


Hide 84720J 2.INSPECT PATTERN SELECT SWITCH ASSEMBLY (SNOW)

a.
C444792C04
1.531,0.24 1.917,0.458 0.385,0.219 0.885,1.823 1.146,1.823 1.146,1.823 1.406,1.281 true 2.667,1.813 2.375,1.813 2.375,1.813 2.063,1.271 true 0.052,0.042 0.323,0.26 0.271,0.219 10 false *a 0.427,1.75 0.917,1.979 0.49,0.229 10 false SNSW 2.729,1.74 2.885,1.938 0.156,0.198 10 false E 1.594,0.271 1.948,0.49 0.354,0.219 10 false D74
*a Component without harness connected
(Pattern Select Switch Assembly (SNOW))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D74)Location & Routing

Click Connector(D74)Instrument Panel>Instrument Panel Wire>Pattern Select Switch Assembly

D74-5 (SNSW) - D74-2 (E) SNOW mode switch pushed and held Below 10 Ω
D74-5 (SNSW) - D74-2 (E) SNOW mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the pattern select switch assembly (SNOW).


b.
C444792C05
1.521,0.24 1.938,0.469 0.417,0.229 0.573,1.833 0.813,1.833 0.813,1.833 1.208,1.292 true 2.24,1.271 2.552,1.844 2.552,1.844 2.781,1.844 true 0.063,0.052 0.344,0.292 0.281,0.24 10 false *a 2.823,1.771 3.177,1.948 0.354,0.177 10 false ILL- 0.271,1.771 0.583,1.969 0.313,0.198 10 false ILL+ 1.594,0.271 1.948,0.5 0.354,0.229 10 false D74
*a Component without harness connected
(Pattern Select Switch Assembly (SNOW))


Apply battery voltage between the terminals of the pattern select switch assembly (SNOW), and check the illumination condition of the pattern select switch assembly (SNOW).

Standard:
Measurement Condition Specified Condition
Battery positive (+) → D74-6 (ILL+)
Battery negative (-) → D74-1 (ILL-)
Illuminates


If the result is not as specified, replace the pattern select switch assembly (SNOW).