Home › Vehicle Interior › MIRROR (INT) › DIGITAL INNER MIRROR
RM37H0E _58 Vehicle Interior _095286 MIRROR (INT) _0448049 DIGITAL INNER MIRROR G

MIRROR (INT)  DIGITAL INNER MIRROR  INSPECTION  


PROCEDURE

Hide 87810 1.INSPECT INNER REAR VIEW MIRROR ASSEMBLY

a.

Inspect the operation of the electrochromic inner rear view mirror assembly.

B605635C01
3.385,0.156 3.792,0.427 0.406,0.271 1.219,2.708 1.729,2.708 false 1.271,3.031 1.781,3.031 false 4.177,1.698 4.031,1.698 4.031,1.698 3.854,1.5 true 0.615,3.177 0.635,2.615 false 3.875,1.271 4.115,1.146 4.115,1.146 4.271,1.146 true 3.74,1.323 3.229,1.031 3.229,1.031 3.115,1.031 true 6.656,2.969 6.563,2.479 false 3.458,0.198 3.917,0.396 0.458,0.198 10 false H14 4.302,1.063 4.76,1.26 0.458,0.198 10 false IG 2.99,0.969 3.448,1.167 0.458,0.198 10 false E 4.24,1.604 4.698,1.802 0.458,0.198 10 false +B 6.615,3.052 7.073,3.25 0.458,0.198 10 false *g 5.083,1.01 5.542,1.208 0.458,0.198 10 false *c 5.156,1.948 5.615,2.146 0.458,0.198 10 false *d 1.813,2.958 2.271,3.156 0.458,0.198 10 false *a 0.531,3.24 0.99,3.438 0.458,0.198 10 false *b 1.813,2.625 2.271,2.823 0.458,0.198 10 false *f 2.448,1.708 2.906,1.906 0.458,0.198 10 false *e 2.948,1.333 3.406,1.531 0.458,0.198 10 false *h
*a Black Colored Tape *b Forward Sensor
*c Bright *d Dark
*e Auxiliary Battery *f Mode Selection Lever
*g Cursor Operation Switch *h Component without harness connected
(Inner Rear View Mirror Assembly)


i.

Connect a positive (+) lead from the auxiliary battery to terminal 1 (IG) and terminal 6 (+B) and a negative (-) lead to terminal 2 (E).


ii.

For digital mirror mode, operate the mode selection lever to switch it to optical mirror mode.


iii.

Attach black colored tape to the forward sensor to prevent it from sensing.

NOTICE:

Clean the forward sensor when detach the black colored tape.



iv.

Press the MENU switch on the selection switch and operate the cursor operation switch to change the mirror surface reflection condition to automatic glare-resistant mode ON (operating condition).


v.

Light up the mirror with an electric light, and check that the mirror surface changes from bright to dark.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(H14)Location & Routing

Click Connector(H14)Body>No. 1 Roof Wire>Inner Rear View Mirror Assembly

H14-1(IG) - Auxiliary battery positive (+)
H14-6(+B) - Auxiliary battery positive (+)
H14-2(E) - Auxiliary battery negative (-)
Light up the mirror with an electric light Inner rear view mirror surface Bright → Dark


If the result is not as specified, replace the inner rear view mirror assembly.